Fresco Solo User manual

1
eng
Age Recommendation
Recommended for use between newborn & 36kg / 79lbs.
Thank you for choosing fresco solo as your baby chair – the fresco is
bloom’s next generation contemporary chair.
FOR A VISUAL GUIDE, PLEASE REVIEW OUR INSTRUCTIONAL VIDEOS AT:
https://vimeo.com/bloomglobal
IMPORTANT!
RETAIN FOR FUTURE REFERENCE: READ
CAREFULLY BEFORE ASSEMBLY AND USE OF
PRODUCT.
Please remove all packaging materials before use.

2
eng
Instructions for safe use-read carefully
and keep for future reference
The correct use and maintenance of your baby
chair will ensure trouble-free use. When somebody
else is using your baby chair ensure they also know
how to use it, how to adjust it and the necessary
safety precautions. The safety of your child is your
responsibility.
NOTE: Adult assembly required.
IMPORTANT!
Store away from natural light – exposure to sunlight
for prolonged periods will fade colors and hasten
aging process.
Section A: Basic Assembly (refer to
illustrations section a)
Swivel/Height Resistor and Base Assembly
IMPORTANT!
The resistor is designed to prevent inadvertent or
free spinning, however with adult force it is still
possible to rotate the seat unit.
To Engage
Press metal lever inwards, until it sits flush with the
plastic housing. Check the device is engaged by
turning the seat unit. (refer to illustration a1)
Product Information
This baby chair has been designed and tested to
ensure compliance with the latest relevant
safety standards.
This baby chair is designed with multiple
configurations of use for babies and toddlers
from newborn to 36kg / 79lbs:
• Reclined cradle mode: from 0 to 6 months
• High chair mode: from 6 months to 15kg /
33lbs
• Toddler chair mode: from 36 months to
36kg / 79lbs
Model No.: 10545
PATENTED:
• US7905549 B2
• USD601818 S1
Colour & contents may vary
TOOL FREE ASSEMBLY

3
eng
To Disengage
Pull the metal lever outwards fully. Check the device
is disengaged by turning the seat unit. (refer to
illustration a1)
Base and Seat Assembly
(#01 swivel shaft, #03 base) Insert the swivel shaft
onto the base by pressing down firmly. (refer to
illustration a2)
(#02 swivel shaft housing) Insert the swivel shaft
housing all the way into the swivel shaft (make
sure the swivel resistor is disengaged). (refer to
illustration a3)
Insert the swivel shaft housing to the base by
aligning the ‘unlock’ icon marking on the base
to the indication line marked on the swivel shaft
housing. Turn until locked into position. You
will hear an audible click. In locked position the
indication icon line should point to the ‘lock’ icon.
(refer to illustration a4)
To disassemble, lift the slide button on side of
swivel shaft whilst turning to align the ‘unlock’
icon to indication line. Pull to remove.
Check the swivel shaft housing is securely locked
by lifting upwards. Press white button on top of
shaft to raise shaft. Engage swivel resistor.
(#04 seat unit) Insert the seat unit onto swivel
shaft making sure not to engage A & B triggers.
Check the seat unit is fully engaged by pressing
down several times on the seat unit. Tighten the
fastening cap counterclockwise. Then engage
the swivel resistor. (refer to illustration a5)
Swivel and Height Adjustment
To rotate the seat unit, disengage the swivel/
height resistor, and then turn the seat unit
sideways to desired position. (refer to illustration
a6)
To adjust the height down, lift both A & B triggers
simultaneously, and push down firmly to the
desired height position. To adjust the height
up, lift both A & B triggers simultaneously and
release at different intervals to adjust to the
desired position. (refer to illustration a7)
IMPORTANT!
Ensure the seat unit is firmly inserted onto the
swivel shaft before use. Check the seat unit
is assembled properly by trying the height
adjustment function, following the instructions
in this user guide. If the height adjustment fails
to work, this means the seat unit is not properly
assembled, please re-try and press seat unit
downwards on the swivel shaft firmly in order
to properly engage the height adjustment
mechanisms.
Lift and Glide – Easy Glide Wheels
To move the baby chair across the floor, the seat
unit must be front facing and in the lowest height
position. To rotate the seat, first disengage the
swivel/height resistor, then rotate the seat to
front facing position. (Refer to illustration a8)

4
eng
Keep the swivel/height resistor disengaged
and lower the seat height by lifting both A &
B triggers simultaneously, and pushing down
firmly to the lowest height position. (refer to
illustration a9)
It is easiest to move the baby chair if the seat is
in the reclined cradle position. To adjust the seat
unit to the reclined cradle position, pull on the
handle on the rear of the seat unit, then recline
the seat to the lowest position and release the
handle. You will hear an audible click. (refer to
illustration a10)
Tilt the baby chair forward by lifting in the handle
area located on the rear of the seat unit, and
then glide the high chair across floor using the
castor wheels, which are located under the front
end of the base. (refer to illustration a11)
WARNINGS:
• Continue to assemble the baby chair
according to the configuration suitable
for your child. Follow the corresponding
instructions carefully.
• A child’s safety is your responsibility.
WARNINGS:
• Prevent serious injury or death from falls or
sliding out.
• Always secure child in the restraint.
• Never leave child unattended.
Section B: Reclined Cradle Mode
– suitable for 0-6 months (refer to
illustrations section b)
WARNINGS:
• Do not use the reclined cradle once your
child can sit unaided.
• Reclined cradle mode is intended for children
with a maximum weight of 9kg.
• Never leave the child unattended when the
baby chair is in reclined cradle mode.
• The child should be secured in the baby
chair at all times by the 5-point safety
harness in reclined cradle mode.
• It is dangerous to put this reclined cradle on
an elevated surface.
• Keep the product away from open fire,
heaters and other sources of strong heat.
• Do not use the product unless all
components are correctly fitted and
adjusted.
• Make sure harness is correctly fitted before
use.
• This reclined cradle is not intended for
prolonged periods of sleeping.
• It is dangerous to put this baby chair on an
elevated surface.
• This reclined cradle does not replace a cot or
a bed. Should your child need to sleep, then
your child should be placed in a suitable cot
or bed.
• Do not use accessories or replacement
parts other than those approved by the
manufacturer.

5
eng
• Do not use the reclined cradle if any
components are broken or missing.
• Always use the restraint system.
Installing Seat Pad and Safety Harness
Before installing seat pad on chair, ensure straps
are in the fully loosened position.
– (#05 seat pad, #06 safety harness) Put 2 waist
straps through the lower side seat pad slits.
(refer to illustration b1)
– (#08 storage compartment) Behind the seat
pad, pull open the storage compartment door
located on the inner face of seat unit. Slide
the buckle on the end of the waist straps into
the buckle slots on either side of the storage
compartment. Check the straps are secured
by pulling on the straps. Close compartment
door. (refer to illustration b2)
– Put shoulder straps through the seat pad slits
at the lower height setting. (refer to illustration
b3)
– (#04 seat unit) Behind the seat pad, slide the
buckle on the end of the shoulder straps into
the buckle slots located on the inner face of
seat unit. Check the straps are secured by
pulling on the straps. (refer to illustration b4)
– Place seat pad onto the seat unit; secure onto
velcro.
– (#10 crotch cover) Insert the seamed end of
the crotch strap through the slot on the crotch
strap cover. Make sure the seamed end is
facing up. Slide the crotch strap cover into the
seat unit. The strap and buckle must not be
twisted or inverted. This will ensure correct
locking of the harness. (refer to illustration b5).
NOTE: The bar attachment caps and crotch
cover come pre-assembled on the chair. If
additional accessories are purchased (for
example: safety bar), you will need to remove
and store the bar attachment caps.
To Attach Bar Attachment Caps
Insert the bar attachment caps on either side of
the seat unit; you will hear an audible click.
To Remove Bar Attachment Caps
To remove the bar attachment caps, press and
hold the button under the two side domes,
and then press the side button on dome cap to
disengage the lock.
WARNING:
Always use the safety harness.
To remove the seat pad & safety harness for
cleaning, follow the instructions given in the care
& maintenance section of this user guide.
Using and Adjusting the Safety Harness
– To lock harness, attach the shoulder straps to
the smart buckle by sliding the shoulder strap
loops onto the upper tabs of the smart buckle.
Push the tongues on ends of waist straps into
the buckle to fasten. (refer to illustration b7)
– To unlock harness, press the central button.
Slide the shoulder strap loops off the upper
tabs of the smart buckle. (refer to illustration
b8)
– Adjust the length of the harness straps until it
fits firmly around your child.

6
eng
NOTE: Every time you place your child in the
baby chair or whenever you alter the position
of the seat always check that the harness is
correctly fitted. Tighten the harness until it fits
snugly around your child.
Seat Unit Height and Seat Unit Recline
– To adjust seat height, disengage the swivel/
height resistor.
– To adjust the height down, lift both A & B
triggers simultaneously, and push down
firmly to the desired height position. (refer to
illustration b9)
– To adjust the height up, lift both A & B triggers
simultaneously and release at different
intervals to adjust to the desired position. (refer
to illustration b9)
– Adjust the seat unit to reclined cradle position
by pulling the handle on the rear of the
seat unit, then recline the seat to the lowest
or intermediate position, and release the
handle. You will hear an audible click. (refer to
illustration b10)
– Check the seat unit is locked in position by
moving it.
– Ensure the seat unit is reclined to the lowest
or intermediate reclined cradle position for
children from newborn to approximately 6
months of age, until child can sit up unaided.
(refer to illustration b11)
WARNING:
Children who cannot sit up unaided can only
use the reclined cradle mode of this baby
chair. Seat unit must be reclined to lowest or
intermediate reclined cradle position. Always
use the safety harness. Always be sure your
child is clear of moving parts before making
any adjustments.
Section C: High Chair Mode – suitable
for 6 – 36 months (refer to illustrations
section c)
WARNINGS:
A CHILD’S SAFETY IS YOUR RESPONSIBILITY.
• NEVER LEAVE THE CHILD UNATTENDED.
• DO NOT USE THE HIGH CHAIR UNTIL THE
CHILD CAN SIT UP UNAIDED.
• DO NOT USE PRODUCT IF ANY PART IS
BROKEN, TORN OR MISSING.
• High chair mode is intended for children
able to sit up unaided (from approximately
6 months) and up to 3 years or a maximum
weight of 15kg / 33lbs.
• The child should be secured in the baby
chair at all times by the 5-point safety
harness in the upright position. It is
recommended that the high chair be used in
the upright position only by children capable
of sitting upright unassisted.
• FALL HAZARD: Children have suffered severe
head injuries including skull fractures when
falling from high chairs. Falls can happen
suddenly if child is not restrained properly.
• Always use restraints, and adjust to fit
snugly.

7
eng
• Stay near and watch child during use.
• Keep the high chair away from open fire,
heaters and other sources of strong heat,
such as electric bar fires, gas fires etc. in the
vicinity of the high chair.
• Do not use the high chair unless all
components are correctly fitted and
adjusted.
• Falling hazard: Prevent your child from
climbing on the product.
• Be aware of the risk of tilting when your
child can push its feet against a table or any
other structure.
• Always use the restraint system.
• Make sure harness is correctly fitted before
use.
• Only use the high chair on a flat, even and
horizontal floor and not to elevate the high
chair on any structure or table.
• Always be sure your child is clear of the
high chair’s moving parts before making
adjustments.
• Check the high chair regularly for damage
and to ensure that the harness is secure
and performs correctly. No lubrication is
necessary.
• IMPORTANT: Every time you place your
child in the high chair or whenever you alter
the position of the seat, always check that
the harness is correctly fitted. Tighten the
harness until it fits snugly around your child.
• MOST INJURIES FROM HIGH CHAIRS ARE
CAUSED BY FALLS.
• POSITION THE HIGH CHAIR AWAY FROM
SOLID STRUCTURES AND BENCHES TO AVOID
INJURIES CAUSED BY FALLS AND BY ACCESS
TO DANGEROUS ITEMS.
• Keep the high chair away from furniture,
walls, hot surfaces and liquids, window
covering cords, and electrical cords and
position the high chair away from furniture
when the chair is not being used at a table
with a tray removed.
• In compliance of ASTM F404 for the US
market and AS 4684 for the Australia
market, the comfort nest shall be installed
on the seat unit for high chair use with
children between 6 months and 3 years.
• In high chair mode the seat unit shall always
be adjusted to the vertical upright position.
Footrest Assembly and Footrest Adjustment
IMPORTANT!
• DO NOT use footrest as a step.
• Suitable for use up to 24 months.
– (#07 footrest) Slide in footrest until you hear
an audible click. Check footrest is secured by
pulling it downwards.
– To remove footrest, press button located on
the end of the footrest attached to the seat
unit, whilst sliding the footrest out of seat unit.
– The footrest has three height positions. Press
the button on the back of the footrest, whilst
sliding footrest up or down to your desired
position. The footrest is locked into position
when you hear an audible click. Check footrest
is secured by pulling it downwards. (refer to
illustration c1)

8
eng
To Install Seat Pad
– Follow “To Install Seat Pad & Safety Harness
Assembly” in section B.
– Adjust the length of the harness straps until it
fits firmly around your child.
Section D: Toddler Chair Mode –
suitable for 36 months to 36kg / 79 lbs
(refer to illustrations section d)
Removing the safety harness
– (#04 seat unit) Behind the seat pad, press the
button on the inside end of the buckle slot,
located on the inner face of the seat unit, and
slide the buckle out of the slot. Repeat for the
other side. (refer to illustration d1)
– (#08 storage compartment) Behind the seat
pad, pull open the storage compartment door
located on the inner face of the seat unit. Slide
the buckle on the end of the waist strap out of
the buckle slots on either side of the storage
compartment. (refer to illustration d2)
– (#10 crotch cover) Press the button on the
crotch cover and remove from the seat unit
(refer to illustration d3)
– Remove the seat pad and safety harness from
seat unit (refer to illustration d4)
– Replace the crotch cover by snapping into seat
unit (refer to illustration d5)
– Replace the seat pad on the seat unit (refer to
illustration d6)
Seat Unit Height Adjust
– To adjust seat height, disengage the swivel/
height resistor.
– To adjust the height down, lift both A & B
triggers simultaneously, and push down
firmly to the desired height position. (refer to
illustration d7)
– To adjust the height up, lift both A & B triggers
simultaneously and release at different
intervals to adjust to the desired position. (refer
to image d7)
WARNINGS:
– In toddler chair mode the seat unit shall
always be adjusted to the vertical upright
position.
– Footrest shall be removed for toddler chair
mode.

9
eng
Section E: Disassembly (refer to
illustrations section e)
Disassembly
– Remove the footrest by following the
instructions in the earlier sections of this
manual.
– Unscrew (turn clockwise) the plastic fastening
cap at the base of the seat unit/top of the
swivel shaft. (refer to illustration e1)
– Remove the seat unit from the swivel shaft by
loosening side to side and pulling upwards.
(refer to illustration e2)
– Remove the swivel shaft housing by lifting the
slide button on the side of the swivel shaft
whilst turning to align the ‘unlock’ icon to the
indication line. Then pull to remove. (refer to
illustration e3)
– Remove the swivel shaft from the base by
tipping the base over and hammering out the
shaft from the bottom. (refer to illustration e4)
Fresco Solo Accessories
The fresco solo can be customized to fit your
needs by purchasing additional accessories.
These accessories include:
• Booster Seat – 6 to 18 months
• Small Seat Pad – 6 – 18 months
• Safety Bar – 6 – 36 months
• Food Tray – 6 – 36 months

10
eng
Care and Maintenance
– First remove the harness straps and waist
straps from the seat unit. (see section D above)
– The seat pad and baby chair can then be
cleaned following the instructions on the care
label of the seat pad.
WARNINGS:
Using an effective disinfectant, for examples
cleaners with alcohol or chlorine content,
may cause bleaching and discoloration, it is
recommended to use cleaners specifically
designed for colored fabrics to spot clean the
fresco seat pad.
Note:
• Exposed edges of seat pad are often the first
to wear and fray. Remember this when storing
or transporting your baby chair.
• Light soiling of seat pad can be removed with
a damp sponge and a mild detergent. Hang
dry. Do not tumble dry.
• Clean the plastic parts of the high chair with a
damp cloth; do not use abrasives or bleach.
• Do not expose the baby chair to direct sunlight
for prolonged periods of time.
Check List
• Regularly check that the safety harness is
correctly fitted and that the webbing has not
become frayed or damaged. If the harness
is damaged, we recommend that a new one
is fitted. For more information contact us by
email at [email protected].
• Regularly check that all locking devices are
clean and functioning properly.
After Sales Service
• When you receive your bloom product, if you
need assistance, spare parts or if you are
unsatisfied with any aspect of the goods,
please contact your local dealer for assistance.
You can also visit our website at bloombaby.
com and click on contact us. Our trained
advisers will be able to help.
• You can also visit our website for the latest
product information.
• Your feedback and input enables bloom to
make continual improvements. Please send
your comments regarding this product to
[email protected].