FRIEDLAND Wirefree Remote Control User manual

These instructions should be read in conjunction
with your System Installation and Operating
Manual and be retained for future reference.
Introduction
These Remote Control units are designed for use with
Friedland Response Wirefree Intruder Alarm systems
operating at 433MHz only.
The Remote Control Unit is used to Arm and Disarm the
system. The Remote will activate the Instant-Arm, Part-Arm
or Delay-Arm functions dependant upon which type of
system it will be used with, (refer to your System Installation
and Operating Manual).
The Remote Control also incorporates a Personal Attack
(PA) switch. Activating the PA switch will immediately
initiate a Full Alarm condition whether the system is Armed
or Disarmed, (unless the system is in Service, Test or
Program mode).
Any number of Remote Controls can be used with your
system, providing they are all coded with the same system
House Code.
The Remote Control is powered by a CR2032 type Lithium
cell which under normal conditions will have an expected
life in excess of 1 year. Under normal battery conditions
the LED on the Remote control will only illuminate when a
button is pressed. However, under low-battery conditions
this LED will continue to flash after the button has been
released. When this occurs the batteries should be
replaced as soon as possible.
Configuring the Remote Control
Ensure that the system is in Test/Service Mode.
1. Remove the rear cover by undoing the small screw on
the rear of the Remote Control.
Slide up
to operate
Transmit LED
Personal Attack
Disarm
Arm/
Instant-Arm
Part-Arm/
Delay-Arm
House Code
Dip Switches
Jumper Link
Battery Clip
Battery
Wirefree Remote Control
Installation and Operating Instructions

Guarantee
Novar ED&S undertakes to replace or repair at its discretion goods (excluding non rechargeable batteries) should they
become defective within 1 year solely as a result of faulty materials and workmanship.
Understandably if the product has not been installed, operated or maintained in accordance with the instructions, has not
been used appropriately or if any attempt has been made to rectify, dismantle or alter the product in any way the
guarantee will be invalidated.
The guarantee states Novar ED&S entire liability. It does not extend to cover consequential loss or damage or installation
costs arising from the defective product. This guarantee does not in any way affect the statutory or other rights of a
consumer and applies to products installed within the UK and Eire only
If an item develops a fault, the product must be returned to the point of sale with:
1. Proof of purchase. 2. A full description of the fault. 3. All relevant batteries (disconnected).
Friedland is a trade mark of Novar ED&S.
HELPLINE
If you have a problem with your alarm,
please call the helpline on:
01268 563273
(Lines open 9.00am to 5.00pm, Monday to Friday).
45175PL Ed.2
2. Located above the battery cover is a row of 8 DIP
switches. These switches set the House Code for the
Remote Control and must be set to the same ON/OFF
combination as the House Code DIP switches in all other
the system devices.
3. If used with a "Siren-controlled" alarm system (i.e. a
system without a separate Control Panel), the jumper link
located immediately below the House Code DIP switches
must be removed.
If your system has a separate Control Panel then this link
must be fitted in place.
4. Insert the battery under the clip ensuring that the +ve
terminal faces upwards away from the PCB.
5. Replace the rear cover and fixing screw. Do not over
tighten the screw as this may damage the moulding thread.
Testing the Remote Control
Return the system to Operating/Standby Mode.
The operation of the Remote Control should be tested with
the system in normal operating mode to ensure that the
new Remote Control will successfully communicate with
the system and the Arm and Disarm functions operate
correctly. Also check that activating the Personal Attack
switch on the Remote initiates an alarm condition.
Refer to your System Installation and Operating Manual for
further details on operating and testing the system.
Friedland, Novar Electrical Devices and Systems.
The Arnold Centre, Paycocke Road, Basildon, Essex SS14 3EA.
© Novar ED&S, 2004