Frigidaire FAA065P7A2 User manual

u m
READ BEFORE iNSTALLING UNIT
MS niWindow Mounting
Your ah"conditioner is desigl_ed to install in skmdard
double lumg windows with opening widths ol 22 to 36
inches (559 mm to 914 ram) (FIG. l)
Lower sash must open suificiemly to allow a clear vertical
opening of 14-1/2 inches (368 ram). Side louvers and the
rear of the AC must have clear air space to allow
enough airllow through the condensel; hn" heat removal.
The rear of the unit must be outdoors, not inside a
building or garage°
When handling unit, be careful to avoid cuts
f?om sharp metal edges and aluminum fins on
front and rear coils.
Beibre installing unit, the top rail must be
assembled on the unit.
_lbp Rail Hardware Qty.
3/8" Screw 4
Top Rail 1
NOTE: SAVE CARTON and these INSTALLA-
TiON iNSTRUCTiONS fin:fmnre reference. The caJlon is
the best way to store unit during wimer, or when not h_use.
Some assemNy is required. Please read these instructions
Mounting Hardware
3/4 'screws
lock frame
sash lock
TOOLS NEEDED:
• Drill (if pik)t hales are needed)
Qty.
7
TOOL NEEDED:
* PhilBips Screwdriver
A. Remove the air
conditioner flTomthe
cmlon and place on a
flat surface.
B. Remove top rail from
tlle bottom of the
packaging material as
shown in Fig. A
C. Align the hole in the
the top of the unit as
shown in Fig. B
D. Secure the top raiI to
rite unit with the 3/8"
Screws as shown in
Fig. (7
Packagitlg .
Top Rail
Fig. A
NOTE: FOR SAFETY REASONS, ALL
FOUR (4) SCREWS MUST BE SECURELY
FASTENED.

How to Install
NOTE: Top Rail and Sliding Panels at each side are
o_gset to provide the proper pitch to the rear of (5/16").
This is necessary for proper condensed water utilization
and drainage. If you are not using the Side Panels for
any reason, this pitch to the rear must be maintained!
Place unit on floor, a bench or a table, There is a
Left and Right Window Filler Panel - be sure to
use the proper panel _i_reach side,When installed
the []ange [or securhlg the panel hi place to the window sill
will be [)acing into the morn,
A. Hold file
Accordion
Pane] in one
hand and
geJlt]y pull
back the
center to }]ee
the open end.
See Figure 2.
C, Once the panel
has been
hlstaHed on the
side of the
cabinet, make
sure it sits
file [rame
making Might
adjustments. SHde the top and bottom ends of the [tame
into the top and bottom rails of file cabinet. Figure 5.
D. Slide the panel aH the way hi and repeat on the oilier
side.
NOTE" If storm window blocks AC, see FIG, 12,
Keep a firm grip on the air conditioner, carefully
place file unit into the window opening so the
bottom of the ai r conditioner }rame is against the
window sill (FIG.
6). Carefully close
the window behind
the top rail of the
unit,
B, Slide the fl:ee end (I"section) of the panel hlto the
cabinet as shown in Figures 3A, 3B & 4_ SHde the
panel down. Be sure to leave el_ough space to sJip the
top and bottom of the fl'ame into the mils on the cabinet. ExteJld the side pands out against the window
h:arne(FIG, 7),

Place the fi°ame lock between the fl°ame
extensions and the window sill as shown
(Fig. 8). Drive 3/4" (19 ram) locking
screws through the frame tock and into the sill
(FIG. 9). NOTE: '[b prevent window sill from
splitting, drill 1/8" (3 ram) pilot holes before
driving screws.
Cut _i)am seal and insert in the space
between the upper and lower sashes
(FIG. 13).
IfAC is Blocked by Storm
Drive 1/2" (13 ram) tocMng screws
through frame holes into window sash
(FIG. 10/11).
"Ii) secure tower sash in place, attach right
angte sash lock with 3/4" (19 mm) screw
as shown (FIG. 12).
Add wood as shown in FIG. 14, or remove storm
window be_i)re ah: conditioner is installed.
FIG. 14 [_SASH
BOARD
STORM WINDOW THICKNESS
FRAME AS REQUIRED,
OR OTHER 1 1/2" MIN FOR PROPER
OBSTRUCTION (38 ram) , PITCH TO
REAR A ON
ENTIRE SILL.
FASTEN WITH
NAILS OR
SCREWS,
If Storm Window Frame must remain, be sure the
drain holes or slots arc not caulked or painted
shut.Accumulated Rain Water or Condensation
must be allowed to drain out.
Removing AC From
* 2k_rn AC off, and disconnect power cord.
* Remove sash seal from between windows,
and unscrew safcD_ lock.
* Remove screws installed through frame and
fl°ame lock.
* Ctose (slide) side panels into frame.
* Keeping a firm ga°ip on air conditioner, raise
sash and carefully "rock" air conditioner
backward to drain any condensate water in
base of unit. Be careful not to spill aW
remaining water while lifting unit from
window: Store parts WITH air conditioner.