Frigidaire GLGF388DSE User guide

NOTICE - This service data sheet is intended for use by persons
having electrical and mechanical training and a level of knowledge
of these subjects generally considered acceptable in the appliance
repair trade. The manufacturer cannot be responsible, nor assume
any liability for injury or damage of any kind arising from the use of
this data sheet.
SAFESERVICINGPRACTICES
To avoid the possibility of personal injury and/or property damage, it is
important that safe servicing practices be observed. The following are
examples, but without limitation, of such practices.
1. Before servicing or moving an appliance remove power cord from
electrical outlet, trip circuit breaker to OFF, or remove fuse.
2. Never interfere with the proper installation of any safety device.
3. GROUNDING: The standard color coding for safety ground wires is
GREEN or GREEN WITH YELLOW STRIPES. Ground leads are not
to be used as current carrying conductors. It is extremely important
that the service technician reestablish all safety grounds prior
to completion of service. Failure to do so will create a potential
safety hazard.
4. Prior to returning the product to service, ensure that:
• All electric connections are correct and secure.
• All electrical leads are properly dressed and secured away from
sharp edges, high-temperature components, and moving parts.
• All uninsulated electrical terminals, connectors, heaters, etc. are
adequately spaced away from all metal parts and panels.
• All safety grounds (both internal and external) are correctly and
securely reassembled.
P/N 316417610REVA(0409)
SERVICE DATA SHEET
GasRanges with ES 510/515Electronic Oven Controls
RTD SCALE
Temperature (°F) Resistance (ohms)
32 ± 1.9 1000 ± 4.0
75 ± 2.5 1091 ± 5.3
250 ± 4.4 1453 ± 8.9
350 ± 5.4 1654 ± 10.8
450 ± 6.9 1852 ± 13.5
550 ± 8.2 2047 ± 15.8
650 ± 9.6 2237 ± 18.5
900 ± 13.6 2697 ± 24.4
ELECTRONICOVENCONTROLFAULTCODEDESCRIPTIONS
ELECTRONICOVENCONTROL(REARVIEW)
IMPORTANT
DO NOT REMOVE THIS BAG
OR DESTROY THE CONTENTS
WIRINGDIAGRAMSANDSERVICE
INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
OVENCALIBRATION
Set the electronic oven control for normal baking at 350°F. Obtain an average oven
temperature after a minimum of 5 cycles. Press STOP/CLEAR to end bake mode.
TEMPERATUREADJUSTMENT
1. Set EOC to bake at 550°F.
2. Within 5 seconds of setting 550°F, press and hold the bake pad for approximately
15 seconds until a single beep is heard (longer may cause F11 shorted keypad
alarm).
3. Calibration offset should appear in the display.
4. Use the slew keys to adjust the oven temperature up or down 35°F in 5°F
increments.
5. Once the desired (-35°to 35°) offset has been applied, press CANCEL or STOP/
CLEAR.
Note: Changing calibration affects normal Bake mode. The adjustments made will not
change the Self-Cleaning cycle temperature.
RESISTANCE
TEMPERATURE
DECTECTOR
RunawayTemperature.
ShortedKeypad.
BadMicroIdentification.
BadEEPROMIdentification/Checksumerror.
Openprobeconnection.
ShortedProbeconnection.
Maximumovendoorunlocktimeexceeded.
Maximumovendoorunlockattemptsexceeded.
Maximumovendooropentimeexceeded.
Maximumovendoorlock time exceeded.
Maximumovendoorlockattempts exceeded.
Likely Failure Condition/Cause Suggested Corrective Action
Fault Code
1.(F10 only)Check RTD SensorProbe &replace if necessary.If ovenis overheating, disconnect
power.Ifovencontinuestooverheatwhenthepowerisreapplied,replaceEOC.Severeoverheating
may require the entire oven to be replaced should damage be extensive.
2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power.
3. (F11, 12 & 13) If fault returns upon power-up, replace EOC.
1.(F30orF31)Check resistanceatroomtemperature&comparetoRTDSensor resistancechart.
If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring
harness between EOC & Sensor Probe connector.
2.(F30orF31)Check resistanceatroomtemperature, iflessthan500 ohms,replaceRTDSensor
Probe. Check for shorted Sensor Probe harness between EOC & Probe connector.
1. (F90, 91, 92, 93 & 94) Check the wiring between EOC & Lock Motor Micro Switch.
2. (F90, 91, 92, 93 & 94) Replace the Motor Door Latch assembly if necessary.
3.(F90, 91, 92, 93&94) Check for bindingof the Latch Cam, LockMotor Rod & LockMotorCam.
4. (F90, 91, 92, 93 & 94) Check to see if Lock Motor Coil is open. If open, replace Lock Motor
Assembly.
5.(F90, 91,92, 93& 94)Lock Motorcontinuosly runs- ifMicro Switchis open,replace LockMotor
Assembly.
6. (F92, 93 & 94) Check oven door Light Switch - if open, replace Switch.
7. If all situations above do not solve problem, replace EOC.
F10
F11
F12
F13
F30
F31
F90
F91
F92
F93
F94
Electrical Shock Hazard
can occur and result in serious injury or
death. Disconnect appliance from electric
power before cleaning and servicing the
Warmer Drawer.
Fig. 1 Fig. 2
REMOVING&REPLACINGWARMERDRAWER(somemodels)
To Remove Warmer Drawer:
1. Turn power off before removing the Warmer
Drawer.
2. Open the drawer to the fully opened position.
3. Locateglide lever on each side of drawer, pull up on the left glide
lever and push down on the right glide lever (see Figure 1).
4. Pull the drawer away from the range.
To Replace Warmer Drawer:
1. Pull the bearing glides to the front of the chassis glide
(see Fig. 2).
2. Align the glide on each side of the drawer with the glide slots on
the range.
3. Push the drawer into the range until levers “click”(approximately
2”). Pull the drawer open again to seat bearing glides into
position. If you do not hear the levers “click” or the bearing
glides do not feel seated remove the drawer and repeat
steps1thru3. Thiswillminimize possibledamagetothebearing
glides.

CIRCUITANALYSISMATRIX GENERALTROUBLESHOOTING SCHEMATIC
ELECTRONICOVENCONTROL(EOC)TROUBLESHOOTINGGUIDE
E.O.C.CONTROLCONNECTIONS
**Convection/SpeedFanwillactivatewithin6minutesorsooner
**