Frigidaire FGHB2866PF6 Owner's manual

Control
Automatic
www.frig

Please read all instructions before using this
refrigerator.
For your Safety
• DO NOT store or use gasoline, or other
flammable liquids in the vicinity of this or
any other appliance. Read product labels for
warnings regarding flammability and other
hazards.
• DO NOToperate the refrigerator inthe
presence of explosive fumes.
• Avoid contact with any moving parts of
automatic ice maker,
• Remove all staples from the carton. Staples
can cause severe cuts, and also destroy
finishes if they come in contact with other
appliances or furniture.
Definitions
_lbThis isthe safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol
to avoid possible injury or death.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
Doors
[] Handles are secure and tight
[] Door seals completely to cabinet on all sides
El Freezer drawer is level across the top
Leveling
[] Refrigerator is level, side-to-side and tilted
1/4" (6 mm) front-to-back
[] Toe grille is properly attached to refrigerator
[] Cabinet is setting solid on all corners
Electrical Power
[] House power turned on
[] Refrigerator plugged in
Ice Maker
[] House water supply connected to
refrigerator
[] No water leaks present at all connections -
recheck in 24 hours
[] Ice maker is turned ON
[] Ice & water dispenser operates correctly
Final Checks
[] Shipping material removed
[] Fresh food and freezer temperatures set
[] Crisper humidity controls set
[] Registration card sent in
Child Safety
Destroy or recycle the carton, plastic bags, and
any exterior wrapping material immediately after
the refrigerator is unpacked. Children should
NEVER use these items to play. Cartons covered
with rugs, bedspreads, plastic sheets or stretch
wrap may become airtight chambers, and can
quickly cause suffocation.
IMPORTANT indicates installation, operation or
normalntenanceinformatiOnhazard_related,which is important but

Proper Disposal of your
Refrigerator or Freezer
Risk of child entrapment
Child entrapment and suffocation are not
)roblems of the past. Junked or abandoned
refrigerators or freezers are still dangerous -
even if they will sit for "just a few days". If you
are getting rid of your old refrigerator or freezer,
)lease follow the instructions below to help
)revent accidents.
Proper Disposal of RefrigeratorslFreezers
We strongly encourage responsible appliance
recycling/disposal methods. Check with your utility
company or visit www.energystar.gov/recycle for
more information on recycling your old refrigerator.
Before you throw away your old
refrigerator lfreezer:
.Remove ....
doors.
*Leave shelves
in place so
children may
not easily
climb inside.
* Have
refrigerant
removed by
a qualified
service technician.
Electrical information
The refrigerator must be plugged into its
own dedicated 115 Volt, 60 Hz., 15 Amp, AC
only electrical outlet. The power cord of the
appliance is equipped with a three-prong
grounding plug for your protection against
electrical shock hazards. ]:t must be plugged
directly into a properly grounded three
prong receptacle. The receptacle must be
installed in accordance with local codes and
ordinances. Consult a qualified electrician.
Avoid connecting refrigerator to a Ground
Fault Interrupter (GF]:) circuit. Do not use an
extension cord or adapter plug.
If the power cord is damaged, it should be
replaced by an authorized service technician to
prevent any risk.
Never unplug the refrigerator by pulling on the
power cord. Always grip the plug firmly, and
pull straight out from the receptacle to prevent
damaging the power cord.
Unplug the refrigerator before cleaning and
before replacing a light bulb to avoid electrical
shock.
Performance may be affected if the voltage
varies by 10% or more. Operating the
refrigerator with insufficient power can
damage the compressor. Such damage is not
covered under your warranty.
Do not plug the unit into an electrical outlet
controlled by a wall switch or pull cord to
prevent the refrigerator from being turned off
accidentally.
Your old refrigerator may have a cooling system
that used CFCs or HCFCs (chlorofluorocarbons
or hydrochlorofluorocarbons). CFCs and HCFCs
are believed to harm stratospheric ozone if
released to the atmosphere. Other refrigerants
may also cause harm to the environment if
released to the atmosphere.
If you are throwing away your old refrigerator,
make sure the refrigerant is removed for
proper disposal by a qualified technician. If
lOU intentionally release refrigerant, you may
be subject to fines and imprisonment under
3rovisions of environmental legislation.
Pressing and holding the On/Off button for
three seconds, located on the temperature
control panel, will disable your refrigerator's
cooling system but does not disconnect the
power to the light bulb and other electrical
components. To turn off power to your
refrigerator you must unplug the power cord
from the electrical outlet.

Grounding type wall receptacle
Do not, under
any circumstances,
cut, remove,
or bypass the
groun_
i iii
Power cord with
3-prong grounded plug .....
To avoid personal injury or property damage,
handle tempered glass shelves carefully.
Shelves may break suddenly if nicked,
scratched, or exposed to sudden temperature

•Features may vary according to model
*Can Rack
Flip
Light
*Store-
Drawer
*LED *Dairy
Cluster Lights WaterComp artment *Air
Ice *Fresh Food
Bin Ice Maker Filter Filter
Flipper
Mullion
Spillsafe ®
Shelves
Cluster
Light
Shelf
Cluster
Light
-- Crisper
Drawer
Bin
Adjustable Hinges
*Freezer Ice
Maker Freezer Baskets
Ice Bin Toe Grille
Features not purchased with your refrigerator can be purchased at www.frigidaire.com
or by calling 1-800-944-9044.
ii

iii__iIi_i_I_L_T_:_I _ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii!!iii,!
Tools Necessary:
Phillips Heac
or
#2 Square
Drive Head Socket
Wrench Set
_%_ Adjustable
\/_ iWrench
OR
Components Provided:
Top Hinge Top Hinge
Cover Front Cover Rear
Screw _ _crew
Top Lower
Hinge
Screw Screw
This Use & Care Guide provides general
installation and operating instructions for your
model. We recommend using a service or kitchen
contracting professional to install your refrigerator.
Use the refrigerator only as instructed in this Use
& Care Guide. Before starting the refrigerator,
follow these important first steps.
Location
Choose a place that is near a grounded,
non-GFCI, electrical outlet. Do Not use an
extension cord or an adapter plug.
If possible, place the refrigerator out of direct
sunlight and away from the range, dishwasher,
or other heat sources.
The refrigerator must be installed on a floor
that is level and strong enough to support a
fully loaded refrigerator.
Consider water supply availability for models
equipped with an automatic ice maker.
DoNot install the refrigerator where the
perature will drop below 55° F (13 ° C) or
rise above 110° F (43 ° C). The compressor will
not be able to maintain proper temperatures
inside the refrigerator.
Do Not block the toe grille on the lower front
of your refrigerator. Sufficient air circulation
is essential for the proper operation of your
refrigerator. ....
Installation
Allow the following clearances for ease of
installation, proper air circulation, and plumbing
and electrical connections:
Sides & Top % inch (9.5 mm)
Back 1 inch (25.4 mm)
_'fyour refrigerator is placed with the door
hinge side against a wall, you may have to
allow additional space so the door can be
opened wider. ....
Door opening
Your refrigerator should be positioned to allow
easy access to a counter when removing food.
For best use of refrigerator drawers and freezer
baskets, the refrigerator should be in a position
where both can be fully opened.
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;ll

Leveling Freezer Drawer (if necessary)
To level the freezer drawer:
1
2
Check gasket seal around top, bottom, and sides of freezer drawer.
If gasket is not sealed, open drawer and slightly loosen four drawer screws (two on each side) to
allow drawer to rotate.
Remove H, _,X
Head Drawer _r
Screw Screw
Remove .... Remove
Hex Head Drawer Hex Head Drawer
Screw Screw
3 Close drawer and recheck the seal on the
gasket (A). Open the drawer grabbing by
the sides in the center (B). Be careful not to
rotate the drawer.
Push Grab _
Against Drawer
Freezer at Center
Drawer from Both
Sides
Drawer
Out
4 Tighten four drawer screws.
5 Recheck gasket seal.
Level Refrigerator &Adjust Doors
(if necessary)
Guidelines for final positioning of your
refrigerator:
All four corners of the cabinet must rest firmly
on the floor.
The sides should tilt 1/4inch (6 mm) from front
to back (to ensure that doors close and seal
properly).
Doors should align with each other and be
level.
Most of these conditions can be met by
raising or lowering the adjustable front
rollers.
To level the cabinet using the front rollers:
1 Slightly open freezer drawer. Lift the toe grille
and gently pull forward (see illustration).
2 You can raise or lower each door. Use a
3/8inch socket wrench to turn the adjustment
screws (one per side).
To raise: turn adjustment screw clockwise.
To lower: turn adjustment screw
counterclockwise.
3 Ensure both doors are bind-free with their
seals touching the cabinet on all four sides
and that cabinet is stable.

4 Afterunitisleveled,loweranti-tipleguntilit
contactsthefloor.
_Raise
Leg
5 Install the toe grille by fitting into place.
To adjest the door stop:
Door stop is adjustable between 85 to 145
degrees.
View shown is looking up at the bottom of the
refrigeratordoor.
Lower
Hinge
Door
)P
Crew
Adjustable Door Stop
1 Open door to provide access to screw.
2 Loosen screw.
3 Adjust door to desired location.
\Door to Desired
LOcation
Adjusting Door
4 Rotate door stop until it makes contact with
the lower hinge.
5 Re-tighten screw,
Door ©
Re-tighten
Screw
Re=tighten Screw
Ensure door stops in desired location before
resuming normal use.
i!!!!!81iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii::_

To level the doors using the adjustable
lower hinge (select models):
1 Remove all food items from door bins on door
being adjusted.
2
3
Open doors to 90 degrees.
Loosenor removescrew.
Loosen or Re
Screw
Bottom of Door
Loosen/Remove Screw (where applicable)
Adjustable hinge should only be used after
doors have been leveled with rollers.
Lift the door while adjusting the washer.
To raise the door, rotate washer clockwise
(when viewed from the bottom). To lower
door, rotate washer counter-clockwise (when
viewed from the bottom).
Hin
To adjust the flipper mullion:
1 Loosen the screw located on the flipper
mullion hinge.
....
Hinge I
Screw
-\
Adjusting Flipper Mullion Screw
Adjust flipper mullion height. For proper
connection with the flipper mullion guide,
there should be a separation about the
thickness of a coin (0.060 inches, or 1.5 mm)
between the guide and flipper mullion.
,, Mullion
I
, dde
I
Flipper
MUllion
Thickness
of a Coin
Adjusting Flipper Mullion Height
3 Re-tighten screw.
Raising/Lowering Door

Getting through narrow spaces
If your refrigerator will not fit through an entrance
area, you can remove the doors. Check first by
measuring the entrance.
To prepare for removing the doors:
1 Make sure the electrical power cord is
unplugged from the wall outlet.
2 Open the freezer drawer and remove the toe
grille (see "Installation" section).
3 Remove any food from the door shelves and
close the doors.
To remove the top hinge covers:
1 Remove the two screws from each cover over
the top door hinges.
2 Lift inside edge of hinge cover and tilt back.
Front Rea_
_r
TopHi Screw
Hinge Ground
Mull
.Top
Hinge
Leave
Hing_ Water
Door Line
Front
Rear Cover Screw
Screw ,,Top Hinge
Cover
Top Ground Hinge
Screws
ire
Cables
Leave
Hinge
With
Door
To remove the refrigerator doors:
1 Trace lightly around the door's top hinges
with a pencil. This makes reinstallation easier.
Disconnect the harness by grasping both
sides of the connector firmly, depress the
latch, and pull apart. Remove the two screws
from the top hinge. Lift the door off of the
bottom hinge and set it aside.
Detach the water tube from the connector
located behind the refrigerator and pull the
tube back out to the front of the unit. The
connector releases when you press inward
on the outer sleeve while pushing the tube
toward the connector then while continuing to
hold in the sleeve, pull the tube away.
Use care while pullingthe water tube from the
unit to be sure that you do not kink the tube.
DO NOT remove the ground screw from hinge.

)roximately
5 feet
You will be pulling approximately five feet of
water tube from the back of the refrigerator.
4 Unscrew the three lower hinge screws and
hinge if necessary.
To reinstall the right door, reverse the above
steps.
Lower Hinge Removal
Once both doors are in place, ensure they are
aligned with each other and level (Please see
the "Installation" section for more details), and
replace the top hinge cover.
When reinserting the water tube and replacing
the top hinge cover, use care to be sure you do
not kink the tube.
Be sure doors are set aside in a secure position
where they cannot fall and cause personal
injury, or damage to the doors or handles.

Removing Freezer Drawer
1 Open freezer drawer.
Remove drawer screws on right and left sides (two screws on each side).
Remove Hex i Remove Hex
HeadDrawer
Screw ;crew
Remove . [emove
Hex Head Drawer Hex Head Drawer
Screw Screw
Do not remove center screw from freezer Drawer is heavy. Use caution when lifting.
drawer. This is a factory adjustment. ....................................................................................................................................................................
.........................................................................................................................................................................................................................................................3 Lift drawer up and out to remove.
Installing Freezer Drawer
1 With lower slides pulled out, hang drawer
onto slide brackets ensuring pins on each side
are fully inserted into slots on each side.
Aisembly Fully Extend
Drawer Slides
in _ .Cabinet
slot_
2 Reinstall four drawer screws (two per side),
tighten down, and close drawer.
3 Check gasket seal around top, bottom, and
sides of freezer drawer.
4 If gasket is not sealed, open drawer and
slightly loosen four drawer screws (two on
each side) to allow drawer to rotate.
Close drawer and recheck the seal on the
gasket (A). Open the drawer grabbing by
the sides in the center (B). Be careful not to
rotate the drawer,
Push
Against
Freezer -
Drawer
A
Grab
Drawer
at Center
from Both
Sides
_" Then
Pull
Drawer
Out
6 Tighten four drawer screws.
7 Recheck gasket seal.
8 Install the toe grille by fitting into place.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii i ! i iliii i!i !i!!i!iii!iii!i i i! i!i!iiiiiiii i i ! iii i iii
Door Handle Hounting
Instructions for Frigidaire
1 Remove handles from carton and
any other protective packaging.
Position fresh food handle end caps
over upper and lower pre-installed
shoulder bolts (A) that are fastened
into door, ensuring the holes for the
set screws are facing towards the
opposite door.
3 While holding handle firmly against
door,fasten upper and lower Allen set
screws (B) with supplied Allen wrench.
Repeat steps 2 and 3 to install
opposite handle. Ensure the holes
for the set screws are facing
towards the first door.
Position freezer handle end caps
over left and right pre-installed
shoulder bolts that are fastened to
the door, ensuring the holes for the
set screws are facing down.
While holding handle firmly against
door, loosely tighten right Allen
set screw (B) with supplied Allen
wrench until there is no gap
between handle and door.
7 Still holding the handle firmly to the
door, firmly tighten left Allen set
screw (B) with supplied Allen wrench.
8 Return to the right Allen set screw
(B) and firmly tighten with supplied
Allen wrench.
Mounting Refrigerator Handles
Mounting Freezer Handle
All set screws should be tightened so the screw is below the surface of the handle. The handles
should be drawn tight to freezer and refrigerator doors with no gaps. Opening the opposite door
while tightening the Allen screw makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this happens, tighten the
set screws on the handles.
Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.

Door Handle Mounting
Instructions for Frigidaire
Gallery ®
1 Remove handles from carton and any
other protective packaging.
Position fresh food handle end
over upper and lower pre-installed
shoulder bolts (A) that are fastened
into door, ensuring the holes for the
set screws are facing towards the
opposite door.
3 While holding handle firmly against
door, fasten upper and lower Allen set
screws (B) with supplied Allen wrench.
Repeat steps 2 and 3 to install
opposite handle. Ensure the holes for
the set screws are facing towards the
first door.
Position freezer handle end over
left and right pre-installed handle
mounts that are fastened to the
door, ensuring the holes for the set
screws are facing down.
6 While holding handle firmly against
door, loosely tighten far right Allen
set screw (B) with supplied Allen
wrench until there is no gap between
handle and door.
7 Still holding the handle firmly to the
door, firmly tighten far left Allen set
screw (B) with supplied Allen wrench.
8 Return to the far right Allen set
screw (B) and firmly tighten with
supplied Allen wrench.
Mounting Refrigerator Handles
Mounting Freezer Handle
All set screws should be tightened so the screw is below the surface of the handle. The handles
should be drawn tight to freezer and refrigerator doors with no gaps. Opening the opposite door
while tightening the Allen screw makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this happens, tighten the
Wear gloves and safety goggles. Use extreme CAUTION when installing these handles.
1

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii:i ! i iliii i!i !i!!i!iii!iii!i i i! i!i!iiiiiiii i i ! iii i iii
Door Handle Mounting
Instructions for Frigidaire
ProfessionaP
1 Remove handles from carton and any
other protective packaging.
Position fresh food handle end
over upper and lower pre-instalied
shoulder bolts (A) that are fastened
into door, ensuring the holes for the
set screws are facing towards the
opposite door.
3While holding handle firmly against
door, fasten upper and lower Allen set
screws (B) with supplied Allen wrench.
Repeat steps 2 and 3 to install
opposite handle. Ensure the holes for
the set screws are facing towards the
first door.
Position freezer handle end over
left and right pre-installed handle
mounts that are fastened to the
door, ensuring the holes for the set
screws are facing down.
While holding handle firmly against
door, loosely tighten far right Allen
set screw (B) with supplied Allen
wrench until there is no gap between
handle and door.
7 Still holding the handle firmly to the
door,firmly tighten far IL=:_t:Allen set
screw (B) with supplied Allen wrench.
8Return to the far right Allen set
screw (B) and firmly tighten with
supplied Allen wrench.
9Rrmly tighten me insideAllen set screws.
\i
Mounting Refrigerator Handles
.... i
Mounting Freezer Handle
All set screws should be tightened so the screw is below the surface of the handle. The handles
should be drawn tight to freezer and refrigerator doors with no gaps. Opening the opposite door
while tightening the Allen screw makes installation easier.
The door handle may loosen over time or if it was installed improperly. If this happens, tighten the
set screws on the handles.
Wear gloves and safety goggles. Useextreme CAUTION when installing these handles.

Toavoidelectricshock,whichcancause
deathorseverepersonalinjury,disconnect
therefrigeratorfromelectricalpowerbefore
connectingawatersupplylinetothe
• Ashutoffvalvetoconnectthewatersupply
linetoyourhouseholdwatersystem.DONOT
useaself-piercingtypeshutoffvalve.
• Donotre-usecompressionfittingoruse
threadsealtape.
•Acompressionnut andferrule (sleeve)for
connecting acopper water supply line to the
ice maker inlet valve.
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing
is recommended for the water supply line.
Water supply tubing made of 1/4inch plastic
is not recommended to be used. Plastic
tubing greatly increases the potential for
water leaks, and the manufacturer will not be
responsible for any damage if plastic tubing
is used for the supply line.
• DO NOT install water supply tubing in areas
where temperatures fall below freezing.
Check with your local building authority
for recommendations on water lines and
associated materials prior to installing your
new refrigerator. Depending on your local/
state building codes, Frigidaire recommends
for homes with existing valves its Smart
Choice ® water line kit 5305513409 (with
a 6 ft. Stainless Steel Water Line) and for
homes without an existing valve, Frigidaire
recommends its Smart Choice ® water line kit
5305510264 (with a 20 ft. Copper Water Line
with self-tapping saddle valve). Please refer to
Chemicals from a malfunctioning water www.frigidaire.com/store for more information.
softener can damage the ice maker. If your ....
home has a water softening system, ensure
the softener is maintained and working
..........ProPer!Y'.........................................................................................................................................................
Ensure that your water supply line connections
comply with all local plumbing codes.
Before Installing The Water Supply
Line, You Will Need:
• Basic Tools: adjustable wrench, fiat-blade
screwdriver, and PhillipsTM screwdriver
Access to a household cold water line with
water pressure between 30 and 100 psi.
A water supply line made of 1/4inch (6.4 mm)
OD, copper or stainless steel tubing. To
determine the length of tubing needed,
measure the distance from the ice maker
inlet valve at the back of the refrigerator to
your cold water pipe. Then add approximately
7 feet (2.1 meters), so the refrigerator can be
moved out for cleaning (as shown).

To Connect Water Supply Line To
Ice Haker Inlet Valve
1 Disconnect refrigerator from electric power
source,
Place end of water supply line into sink or
bucket. Turn ON water supply and flush
supply line until water is clear. Turn OFF water
supply at shutoff valve.
3 Remove plastic cap from water valve inlet and
discard cap.
If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve) onto
water supply line. Push water supply line
into water valve inlet as far as it will go
(1/4 inch/6.4 mm). Slide ferrule (sleeve) into
valve inlet and finger tighten compression nut
onto valve. Tighten another half turn with a
wrench; DO NOT over tighten. See Figure 1.
If you use stainless steel tubing - The nut and
ferrule are already assembled on the tubing.
Slide compression nut onto valve inlet and
finger tighten compression nut onto valve.
Tighten another half turn with a wrench; DO
NOT over tighten. See Figure 1.
5 With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel
of refrigerator as shown.
Coil excess water supply line (copper tubing
only), about 21/2turns, behind refrigerator
as shown and arrange coils so they do not
vibrate or wear against any other surface. Do
not kink tubing.
7 Turn ON water supply at shutoff valve and
tighten any connections that leak.
8 Reconnect refrigerator to electrical power
source.
To turn ice maker on, lower wire signal arm
(freezer ice maker) or set the ice maker's On/
Off power switch to the "On" position (fresh
food ice maker).
Plastic Water Tubin
to Ice Maker Clamp
Compression
Nut
rule
(Sleeve)
r Line
Ive
Bracket
;Inlet
_ehold
water supply
(Includeenoughtubingin loopto allow
movingrefrigeratoroutfor cleaning.)
Figure 1
After connecting the water supply, refer to
"How to Prime the Water Supply System" for
important information about priming an empty
water supply system.
Your refrigerator's water supply system includes
several tubing lines, a water filter, a water
valve, and a water tank. To ensure that your
water dispenser works properly, this system
must be completely filled with water when your
refrigerator is first connected to the household
water supply line.
'17

User Interface (options may vary)
Enlarged view of user interface display menu (options may vary)

Options Hay Vary
exit
quick
freeze on
off
Toggles the options and run
modes.
Activates a faster rate for
freezing food and increases
ice production in the freezer.
Deactivates after 12 hours.
default
settings
water
While in the default option,
press and hold the set key
for three seconds to reset all
refrigerator settings to their
factory default settings.
Press the "water" key to select
water. A green indicator light will
be illuminated above the active
feature.
Toggles the temperature
displays On and Off.
crush Press the "crush" key to select
crushed ice. A green indicator
light will be illuminated above
the active feature.
water filter
Allows the temperature set-
points to be adjusted. Control
temperatures range from -6°F /
-21°C to +6°F /-15°C.
Toggles dispenser light On and
Off.
Displays the current status of
the water filter (Good, Order,
or Replace). To reset the filter
status to "Good', press and hold
the "set" key for three seconds.
Setting cooling temperatures
(options may vary)
When you first power on the refrigerator, the
temperature displays 0°F and 37°F. After a
few seconds, both of the displays will switch to
"HI': The displays will continue to show "HI" for
20 minutes. After 20 minutes, the High Temp
alarm will sound and both displays will show
.........the actual temperature.
1
2
Plus (+) and Minus (-) indicators are located
on the right side of the control panel.
Press the + or - indicator to adjust the
temperature to the desired setting.
'19

Alarms
Power Failure
Inthe event of a power failure, the power fail
alert will be illuminated. Press alarm reset to
acknowledge the alarm. Other modes may be
turned off until the alarm is acknowledged. When
the power fail alert is acknowledged, the refrigera-
tor will resume normal operation. The high temp
alarm may also be illuminated until a safe operat-
ing range temperature has been reached.
Freezer Temp
If the freezer temperature reaches 26°F or
greater, the alarm will sound and the temperature
will flash. You can disable the alarm by pressing
the set key but the "High Temp" indicator will il-
luminate until the temperature goes below 26°F.
Fresh Food Temp
If the fresh food temperature reaches 55°F or
greater, the alarm will sound and the temperature
will flash. You can disable the alarm by pressing
the set key but the "High Temp" indicator will il-
luminate until the temperature goes below 55°F.
Door Ajar
If the freezer or fresh food doors have been left
open for five minutes or more, an alarm will sound
and the door ajar indicator will illuminate on the
display. Press the set key to reset any system
alarms.
Flapper
When "Cube" or "Crush" is selected, if the flap-
per (or ice chute door) is being held open by a
jammed ice cube, an alarm will sound for two
minutes. The alarm will reset after two minutes or
when the ice cube is removed and the set key is
pressed to reset.
Sabbath Mode
The Sabbath Mode is a feature that disables
portions of the refrigerator and its controls
in accordance with observance of the weekly
Sabbath and religious holidays within the
Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by pressing
and holding both the "v" and "+" for five seconds.
The display shows "Sb" while in Sabbath mode.
In the Sabbath Mode, the High Temp alarm is
active for health reasons. If a high temperature
alarm is activated during this time, for example
due to a door left ajar, the alarm will sound
intermittently for about two minutes. The alarm
will then silence on its own and a red high
temperature icon will display. The high temp icon
will continue to display, even if the door is closed,
until the Sabbath mode is exited and the icon
reset. The refrigerator will function normally once
the door is closed, without any violation of the
Sabbath/Holidays.
For further assistance, guidelines for proper usage
and a complete list of models with the
Sabbath feature, please visit the web at
http:\\www.star-k.org.
While in Sabbath Mode, neither the lights,
dispenser, nor the control panel will work until
Sabbath Mode is deactivated.
Refrigerator stays in Sabbath Mode after power
failure recovery. It must be deactivated with the
bu_°ns °n the c°ntr°! pane!: ...............................................
Although you have entered the Sabbath Mode,
the ice maker will complete the cycle it had
already initiated. The ice cube compartment will
remain cold and new ice cubes can be made
with standard trays.
20