Frigidaire FRS24WSG User manual

Versión en español ..................................... 2
Product Registration ................................... 2
Important Safety Instructions .................. 2-3
First Steps ................................................... 3
Energy Saving Ideas .................................. 4
Setting the Controls .................................... 4
Fresh Food Storage.................................... 5
Automatic Ice and Water Dispenser....... 6-9
Care and Cleaning............................... 10-11
Removing the Handles and Doors........... 12
Avoid Service Checklist.......................13-16
Normal Operating Sounds........................ 16
Warranty (United States).......................... 17
Service Information (Canada).................. 18
Warranty (Canada) ................................... 19
P/N 218870500A (9803)

2
Versión en español
Si desea obtener una copia en
español de este Manual del Usuario,
sírvase escribir la dirección que
se incluye a continuación. Solicite
la P/N 218870600.
Spanish Owner's Guides
Frigidaire Home Products
104 Warren Road
Augusta, Georgia 30907-3755
Proper Disposal of
Your Refrigerator
DANGER
Risk of child entrapment.
Child entrapment and suffocation are
not problems of the past. Junked or
abandoned refrigerators are still
dangerous - even if they will sit for "just
afewdays." Ifyouaregettingridofyour
old refrigerator, please follow
instructions below to help prevent
accidents.
BEFORE YOU THROW AWAY YOUR OLD
REFRIGERATOR OR FREEZER:
* Take off doors.
* Leaveshelvesinplace,sochildrenmay
not easily climb inside.
Important Safety
Instructions For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity
of this, or any other appliance. Read product labels for flammability and other warnings.
• Destroy carton, plastic bags, and any exterior wrapping material immediately
aftertherefrigeratorisunpacked.Childrenshouldneverusetheseitemsforplay.
Cartons covered with rugs, bedspreads, plastic sheets, or stretch wrap may
become airtight chambers that can quickly cause suffocation.
• Remove all staples from the carton. Staples can cause severe cuts, and ruin
finishes if they come in contact with other appliances or furniture.
• An empty, discarded ice box, refrigerator, or freezer is a very dangerous
attraction to children. Remove door of any appliance that is not in use,
even if it is being discarded.
•Refrigerator must be plugged into its own 115 Volt, 60 Hz, AC only
electrical outlet. The power cord of the appliance is equipped with a three-
prong grounding plug, for your protection against shock hazards. It must be
plugged directly into a properly grounded three-prong receptacle. The
receptacle must be installed in accordance with local codes and ordinances.
Consult a qualified electrician. DO NOT USE AN EXTENSION CORD OR AN
ADAPTER PLUG.
• If voltage varies by 10 percent or more, performance of your refrigerator may
beaffected. Operatingthe refrigeratorwithinsufficientpowercandamagethe
compressor. Such damage is not covered under your warranty. If you suspect
your voltage is high or low, consult your power company for testing.
• To prevent the refrigerator from being turned off accidentally, do not plug the
unit into an outlet controlled by a wall switch or pull cord.
• Do not pinch, knot, or bend the power cord in any manner.
Child Safety
Product Registration Record the Model Number and Serial Number of this refrigerator in the space
providedbelow.Thesenumbersarefoundontheserialplate,locatedontheceiling
of the refrigerator compartment.
Model Number:
Serial Number:
Register Your Product
Theself-addressed PRODUCTREGISTRATION CARD shouldbe filledincompletely,
signed and returned to Frigidaire, or in Canada, Frigidaire Canada.
© 1998 White Consolidated Industries, Inc.
All rights reserved.
Read all instructions before
using this refrigerator.
Avoid fire
hazard or electric shock. Do
not use an extension cord or
an adapter plug. Do not
remove any prong from
power cord.
Electrical Information
Theseguidelinesmustbefollowed toensurethat safetymechanismsin the
design of this refrigerator will operate properly.

3
Other Precautions
• Neverunplugtherefrigeratorbypullingonthepowercord.Alwaysgriptheplug
firmly, and pull straight out from the receptacle.
• To avoid electrical shock, unplug the refrigerator before cleaning and before
replacingalightbulb. Note: Turning the controltoOFF turns off thecompressor,
but does not disconnect power to the light bulb or other electrical components.
• Do not operate the refrigerator in the presence of explosive fumes.
• Avoid contact with any moving parts of the automatic ice maker.
First Steps This Owner’s Guide provides specific operating instructions for your model. Use
refrigeratoronlyasinstructedinthisOwner’sGuide. Beforestartingrefrigerator,
follow these important first steps:
Location
Install refrigerator:
• near a grounded electrical outlet. DO NOT use an extension cord or an adapter plug.
• outofdirectsunlightandawayfromrange,dishwasher,orotherheatsources,
if possible.
• onafloorthatislevelandstrongenoughtosupportafullyloadedrefrigerator.
• where a water supply is available for automatic ice maker.
Installation
• Donotinstallrefrigeratorwheretemperaturewilldropbelow60°F(15°C),orrise
above110°F(43°C). Compressorwillnotbeabletomaintainpropertemperatures.
• In a recessed installation, allow an extra 1/2 inch (10-15 mm) on each side for
ease of installation.
• If the hinge side of the unit will be placed against a wall, allow a 1-3/4 inch (44
mm) space between wall and refrigerator to permit proper door swing.
Door Opening
For best use of drawers and freezer basket, refrigerator should be in a position
where both the refrigerator and freezer doors can be opened about 135°.
Leveling
• Refrigeratormustbeleveledwithallbottomcornersrestingfirmlyonasolidfloor.
Adjust front rollers to level cabinet both front-to-rear and side-to-side. Keep
cabinetaslowaspossibleforstability. Neveradjustcabinetrollerssofrontislower
than rear.
•To adjust front rollers: Open refrigerator and freezer doors. Remove toe grill
by pulling it straight out. Adjust rollers by turning each roller adjusting bolt with
an adjustable wrench, a socket wrench, or a nutdriver until refrigerator is level
and stable. Rear rollers are not adjustable.
• Check both doors to be sure seals touch cabinet evenly on all four sides.
• Iffreezerdoorishigherthanrefrigeratordoor,raiserightcornerand/orlowerleft
corner until doors align across top of cabinet.
• Ifrefrigeratordoorishigherthanfreezerdoor,raiseleftcornerand/orlowerright
corner until doors align across top of cabinet.
•To replace toe grill: Line up tabs with holes, and push grill straight on.
Cleaning
• Wash the inside, all removable parts, and the outside with mild detergent and
warmwater. Wipedry. DONOTUSEHARSHCLEANERSONTHESESURFACES.
• Do not use razor blades or other sharp instruments that can scratch appliance
surface, when removing adhesive labels. Any glue left from the tape or energy
labelcanberemovedwithamixtureofwarmwaterandmilddetergent,ortouch
glue with sticky side of tape already removed.
• DO NOT REMOVE SERIAL PLATE.
Important Safety
Instructions (continued)
Adjusting Front Rollers
ROLLER ADJUSTING
BOLT
Replacing Toe Grill

4
C05C0063
• Installtherefrigeratorinthemostcoolpartoftheroom,outofdirectsunlightand
away from heating ducts or registers. Do not place the refrigerator next to heat-
producing appliances such as a range, oven or dishwasher. If this is not possible,
asectionofcabinetryoranaddedlayerofinsulationbetweenthetwoappliances
will help the refrigerator operate more efficiently.
• Level the refrigerator so the doors close tightly.
• Refer to this Owner's Guide for the suggested refrigerator settings.
• Periodic cleaning of the condenser will help the refrigerator run more efficiently.
See Outside in the "Care and Cleaning" section.
• Do not overcrowd the refrigerator or block cold air vents. Doing so causes the
refrigeratortorunlonger and usemoreenergy. Shelves should notbelined with
aluminum foil, wax paper or paper toweling. Liners interfere with cold air
circulation,makingtherefrigeratorlessefficient,whichcouldcausefoodspoilage.
• Coverfoodsandwipecontainersdrybeforeplacingthemintherefrigerator.This
cuts down on moisture build-up inside the unit.
• Organize the refrigerator to reduce door openings. Remove as many items as
needed at one time and close the door as soon as possible.
Setting the Controls Cool Down Period
Toensuresafefoodstorage,allowtherefrigeratortooperatewiththedoorsclosed
for at least 8 to 12 hours before loading with food.
Refrigerator Control
• Therefrigeratorcontrolshouldbesetatthemidpointofthedialforatrialperiod
of 24 hours.
• After 24 hours, adjust the control as needed. For colder temperatures, turn the
dial a notch toward COLDEST. For warmer temperatures, turn the dial a notch
toward COLD. Adjust temperatures by one increment at a time.
Freezer Control
• The freezer control should be set at the midpoint of the dial for a trial period of
24 hours.
• After 24 hours, adjust the control as needed. For colder temperatures, turn the
dial a notch toward COLDEST. For warmer temperatures, turn the dial a notch
toward COLD. Adjust temperatures by one increment at a time.
Note: When first setting the controls or when changing a setting, wait 24 hours
for the temperature to stabilize before making additional changes.
Turning the freezer control may change temperatures in both compartments. For
example,if thefreezercontrolisturnedtoacoldersetting, therefrigeratorcontrol
may have to be adjusted to a warmer one. Turning the refrigerator control will
change only the refrigerator temperature.
IMPORTANT: If the freezer control is turned to OFF, cooling stops in both
compartments.
You may hear the "Frost Free" system working. A fan circulates air in the
refrigerator and freezer compartments. For good circulation and maintenance of
proper cooling temperatures, do not block cold air vents with food items. Water
draining into the defrost water pan and hissing sounds are normal during the
automatic "Frost Free" cycle.
Energy Saving Ideas
Freezer midpoint
Refrigerator midpoint

5
Fresh Food Storage Shelf Adjustment
Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting
shelves,removeallfood.Theshippingclipswhichstabilizetheshelvesforshipping
may be removed and discarded.
To adjust the cantilever shelves (shelves supported at the rear of the refrigerator),
lift the back of the shelf up and out. Replace shelf by inserting hooks at rear into
slots. Lower and lock into position. Some models have Spillsafeglass shelves,
which catch and hold accidental spills.
Door Storage
Doorbinsandshelvesareprovidedforconvenientstorageofjars,bottlesandcans.
Items used often are available for quick selection.
Thedoorbinscanbemovedtosuitindividualneeds.Removebinsbyliftingstraight
up. Place bins in the desired position and lower over the supports.
The Dairy compartment is warmer than the general food storage section and is
intended for short term storage of cheese, spreads, or butter.
Crisper
TheCrisperdrawer,locatedunderthebottomrefrigeratorshelf,isforstoringfruits
andvegetables.Mostproduceshouldbewashedinclearwateranddrainedbefore
placinginthisdrawer.Itemswithstrongodorsorhighmoistureshouldbewrapped
before storing.
The Humidity Control (some models) allows you to adjust the humidity within the
Crisperdrawer.Thiscanextendthelifeoffreshvegetableswhichkeepbestinhigh
humidity. Leafy vegetables, however, keep best when stored with the Humidity
Control set on HIGHER, or in a drawer without a Humidity Control. This keeps
incoming air to a minimum and maintains maximum moisture content.
Meat Keeper
The Meat Keeper is located at the bottom of the refrigerator. The temperature in
this compartment can be made colder than the rest of the refrigerator compart-
ment by sliding the Chilled Air Control knob within the COLDEST or COLD range.
Meat will be partially frozen and may be kept fresh longer than if stored on a
refrigerator shelf.
BeforeplacingitemsintheMeatKeeper,followthesestepstokeepthemeatfresh:
1. Carefully handle meat with clean hands and always keep the compartment
clean.
2. Store meat in its original wrapper. If necessary, overwrap in plastic wrap or foil
to prevent drying. Wrap fish tightly to prevent odor transfer to other foods.
3. If spoilage ever occurs, disinfect the compartment with liquid chlorine bleach
followinglabeldirections.Then rinse withasolutionof baking soda andwater.
Rinse with clear water and dry.
Freezer Basket
A slide-out wire basket (some models have two) hangs below the bottom freezer
shelf. This basket provides easy access to frozen food packages.
Tall Storage Compartment (some models)
A shelf is attached to the freezer wall just below the ice server. This allows for
convenient storage of tall items placed vertically between the ice server and the
freezer wall.
Remove Shipping Clips
Lift up
and out
Cantilever Shelf
FRESH FRUITS & VEGETABLES
LOWER
FRUITS
HIGHER
HUMIDITY CONTROL
VEGETABLES
Humidity Control
Chilled Air Control
Tall Storage
Compartment

6
Automatic Ice and
Water Dispenser The ice and water dispenser on the freezer door conveniently dispenses chilled
water, and either ice cubes or crushed ice, depending on the model.
To operate the dispenser, slide the knob to the selection of your choice and press a
glass against the dispensing arm, as shown. Be sure to hold the glass as far up as
possible to catch all ice. To stop dispensing, pull glass away from dispensing arm.
When dispensing ice, release the dispensing arm before the glass is full, but do not
remove the glass until the ice has completely dispensed.
Asmallheatedareabeneaththedispenserfloorcatchesandevaporatessmallspills.
Do not pour water or excess cubes into this area because there is no drain.
Light
The dispenser has a light which can be turned on and off by sliding the knob to the
desired position. The light also turns on automatically when ice and/or water is
dispensed. Replace light bulb with an appliance bulb of the same wattage.
How the Water Dispenser Works
The water tank is located behind the drawers in the refrigerator compartment. As
thewaterisdispensed,thetankisautomaticallyrefilled.Forproperoperationofthe
dispenser, the supply water pressure must fall between 30 psi and 120 psi.
After the refrigerator is installed and the plumbing connections are complete, the
water tank should be filled by drawing one glass of water. It may take
about 1-1/2 minutes after depressing the dispenser arm before water works its
way through the plumbing connections and begins to fill this first glass. Draw and
discard7moreglassestobesurethatthetankandplumbingconnectionsarerinsed
of any impurities.
To ensure fresh-tasting water, plan to use the dispenser every day. If the water
dispenser has not been used for a week or more, draw and discard 7-8 glasses to
freshen the tank supply.
How the Ice Dispenser Works
The ice maker and ice storage bin are located in the top left corner of the freezer
compartment. After the refrigerator is installed properly and has cooled for several
hours,theice maker canbeginmakingice. To beginiceproduction, lower thewire
signalarmtothe"down"orONposition.Ascubesaremade,theyarestoredinthe
storagebin.Withnousageitwilltakeapproximately2daystofillthebin.However,
the dispenser may be used after the first batch of ice is made. The ice maker turns
off automatically when the ice storage bin is full.
Because of new plumbing connections, the first production of ice cubes may be
discolored or have an odd flavor. These should be discarded until the cubes made
are free of discoloration and taste. Remember that water quality
determines your ice quality. It is best to connect the ice maker to water that is not
softened. Chemicalsfroma malfunctioningsoftener candamagethe icemaker. If
icemakerisconnectedtosoftwater,ensurethesoftenerismaintainedandworking
properly.
To stop the ice maker, lift the wire signal arm until it clicks and locks in the "up" or
OFF position.
Wire
Signal Arm
Ice Maker
C05U0030 C05U0029
Dispenser Selector
Press glass against dispensing arm.

7
Do not use the ice
chute as a handle when removing
or replacing the ice storage bin.
Surfaces there may be sharp.
WARNING
Ice Dispenser Tips
1. Ice cubes stored too long may develop an odd flavor. Empty the container and
return it to the proper position. The ice maker will then produce more ice.
2. Occasionally shake the container to keep ice separated.
3. Ifthedispensingarmispushedinformorethan4minutes,thedispensermotor
may overload and stop. The overload protector will reset automatically after 3
or4 minutes.Ifalargequantityoficeisneeded atone time,it isbesttoremove
cubes directly from the ice storage bin.
4. Certain sounds are normal when the ice maker is operating. They are:
• Motor operation
• Ice being loosened from the tray
• Ice dropping into the storage bin
• Running water
• Water valve opening or closing
For more information on these operations, see "Normal Operating Sounds."
5. Stop the ice maker when cleaning the freezer or for long vacations.
6. Iftheicemakeristobeturnedoffforalongperiodoftime,turnthewatersupply
valve to the closed position.
Automatic Ice and
Water Dispenser
(continued)
Cleaning the Ice Dispenser
Clean the dispenser and ice storage bin at regular intervals, particularly before you
take a vacation or move, or if the ice dispenser sticks.
1. Stop ice production by lifting the wire signal arm to the "up" or OFF position.
2. Remove ice storage bin by lifting up and out. Empty and carefully clean the bin
with milddetergent. Do not submergethebin while cleaning. Rinsewithclear
water. Do not use harsh or abrasive cleaners. Allow ice bin to dry completely
before replacing in the freezer.
3. Remove ice chips and clean the shelf and chute that supports the ice storage
bin.
4. Replace the ice storage bin. Lower the wire signal arm on the ice maker to the
"down" or ON position and the ice maker will resume production.
IMPORTANT: When removing or replacing the ice bin, do not rotate the auger
in the ice bin. If the auger is accidentally turned, you must realign the auger by
turning it in 90° turns until the ice bin fits into place with the drive mechanism.
For further instruction, see the label on the ice bucket.
Remove and empty the ice storage bin if:
1. An extended power failure (one hour or longer) causes ice cubes in the ice
storage bin to melt and freeze together and jam the dispenser mechanism.
2. Theicedispenserisnotusedfrequently.Icecubeswillfreezetogetherinthebin
and jam the dispenser mechanism. Remove the ice storage bin and shake to
loosen the cubes.
NEVER use an ice pick or similar sharp instrument to break up the ice. This could
damage the ice storage bin and dispenser mechanism.
PureSource™ Ice and Water Filter (some models)
NOTE: If you purchased a refrigerator with a PureSource Ice and Water
filter,please readthefollowing useandcare information. Thisiceandwater
filtersystemfilterswater to youricemaker and water dispenser. Itislocated in the
upper right back corner of the fresh food compartment (see Figure 1 on the
following page ).
System Startup:
Water supply does not need to be turned off, however do not use ice and water
dispenserwhileinstallingfilter. RefertoFigure1asyoucompletetheseinstructions.
1. Take filter cartridge, large O-ring, and wrench from parts bag in crisper pan.
2. Set ice maker lever (signal arm) to the OFF (up) position.
3. Unscrew filter cup, counterclockwise (Figure 1). If you have trouble unscrewing
cup, use the cup removal wrench included in parts bag (Figure 2).
Repositioning the Auger
AUGER
DRIVER
MECHANISM
DO NOT PUT FINGERS UP ICE CHUTE.
SURFACES THERE MAY BE SHARP.

8
Automatic Ice and
Water Dispenser
(continued)
4.YoumustreplaceexistinglargeO-ringonfilterhousing. Firstremoveoldringand
discard. (Youmayneedtouseatoothpicktogetunderring. NOTE: Usecaution
so that groove that holds ring is not damaged!) Carefully remove new O-
ringfromsealedbag. GentlyrollO-ringintoplace,intocontainmentgroove
above threads.
5. Remove packaging from filter cartridge.
6. Place filter cartridge in cup. The end with the small o-ring should be up, out of
the cup.
7. Screwcup,withfilter,backontohousing. DONOTUSEWRENCHTOREINSTALL
CUP. Filtercartridgewillself-alignascupistightened. Besurecupiscompletely
tightened with PureSource™ Logo facing outward. DO NOT TIGHTEN PAST STOP.
8. Set ice maker lever to the ON (down) position.
9. Check for leaks. Open refrigerator door. Wipe any water drops from filter cup.
Run a glass of water. If there is a leak, unscrew filter cup, and reinsert filter
cartridge. Check placement of large O-ring (see directions following). Reinstall
filter cup.
Remember to keep your wrench handy!
Water Filter Wrench
10. To condition filter system and purge air from water line, run several glasses
of water through water dispenser. This will also assure the purest water
possible is stored in water tank.
Figure 1
Threads
Filter Cup
Filter Housing Large O-ring
Small O-ring
Filter Cartridge
Figure 2

9
As a reminder to change your filter and O-ring, set control box marker 12 months
from date of replacement (Figure 3).
Automatic Ice and
Water Dispenser
(continued)
If you replace filter in
JUN, set marker to JUN.
Ordernewfiltercartridgesthrough the
dealer where you bought the
refrigerator, or contact the Frigidaire
Consumer Assisting Center at
1-800-944-9044. It might be good to
ordersomefilters whenyoufirstinstall
your refrigerator.
Changing the Filter and Large O-Ring:
Water quality varies throughout the world. To ensure the highest possible water
quality, change water filter and O-ring every 12 months. Also, if filter has been in
a refrigerator that has not been in use for awhile (during moving for example),
changefilterbeforereinstallingrefrigerator. Notedispensersystemwillalsooperate
without filtration (with filter cartridge removed).
To change filter and large O-ring:
Refer to Figure 1 as needed.
1. Set ice maker lever (wire signal arm) to the OFF (up) position.
2. Holdfiltercupfirmly,andunscrewcounterclockwise(Figure1). Usecupremoval
wrenchif necessary(Figure2). (Somewatercouldleak out as you remove cup.
Thisisnormal.) Filtercartridgewillcomedownwithcup. Ifcartridgeremains
in housing, pull down gently, while twisting filter back and forth.
3. Replace large O-ring on filter housing. First remove old ring and discard. (You
mayneed touseatoothpickto getunder ring. NOTE: Use cautionso that
neither ring, nor groove that holds ring are damaged!) Carefully
remove new O-ring from sealed bag. Gently roll O-ring into place, into
containment groove above threads.
4. Empty cup of any substance.
5. Discard old filter cartridge.
6. Remove new filter cartridge from packaging, and install. See Steps 6-10 in
“System Startup.”
Figure 3

10
Care and Cleaning Keepyourrefrigeratorandfreezercleantopreventodorbuild-up.Wipeupanyspills
immediately and clean both sections at least twice a year. Never use metallic
scouringpads,brushes,abrasivecleanersorstrongalkalinesolutionsonanysurface.
Do not wash any removable parts in a dishwasher.
Always unplug the power cord from the wall outlet before cleaning.
NOTE: Turning the control to OFF does not disconnect power to the controls, light
bulb, or other electrical components.
Inside
Washinsidesurfacesoftherefrigeratorandfreezerwithasolutionof2tablespoons
bakingsodain1quartwarmwater.Rinseanddrythoroughly.Besuretowringexcess
wateroutof spongeorcloth beforecleaning around thecontrols, lightbulb,or any
electrical parts.
Washremovablepartssuchasshelvesanddrawerswithbakingsodasolutionormild
detergent and warm water. DO NOT USE HARSH CLEANERS ON THESE SURFACES.
Rinse and dry thoroughly. Clean the door gaskets with mild suds, rinse with clear
water and wipe dry. Do not use razor blades or other sharp instruments which can
scratchtheappliancesurfacewhenremovingadhesivelabels.Anyglueleftfromthe
tape or energy label can be removed with a mixture of warm water and mild
detergent,or,touchthe glue with thestickysideof tape already removed.DONOT
REMOVE THE SERIAL PLATE.
Outside
Washthecabinetandhandleswithwarmwaterandmildliquiddetergent.Rinsewell
and wipe dry with a clean soft cloth. Do not use commercial household cleaners,
ammonia, or alcohol to clean handles.
Remove any dust or dirt from the front of the toe grill using a vacuum cleaner with
itsdusting toolattachment. Removethe toegrill bypulling itstraight out.While the
grill is removed, vacuum the backside of the grill and wipe with a sudsy cloth or
sponge. Periodically clean the condenser (black tubes and wires beneath the
refrigerator,behindthetoegrill).Donotallowlintordusttoaccumulateonthecoils.
Insert a long handled brush or vacuum attachment between the two coils to bring
thelintforward.Toreplacethetoegrill,lineuptabswithholesandpushgrillstraight
on. Use caution when cleaning in the area of the coils. Surfaces
there may be sharp.
The air vents on the lower access panel at the rear of the refrigerator should be
cleanedperiodically.Cleantheventsbyusingavacuumcleanerwithitsdustingtool
attachment. When moving the refrigerator, pull straight out. Do not shift the
refrigeratorfromsidetosideasthismaytearorgougethefloorcovering.Becareful
not to move the refrigerator beyond plumbing connections.
Damp objects stick to cold
metalsurfaces.Do not touchrefrigerated
surfaces with wet or damp hands.
To avoid damage and help
the refrigerator run as efficiently as
possible, clean the condenser and air
vents periodically.
Air Vents on Lower Access Panel
Replacing the Light Bulb
To replace the light bulb in either compartment:
1. Unplug the refrigerator.
2. Wear gloves as protection against possible broken glass.
3. Replace old bulb with an appliance bulb of the same wattage.
4. Remember to plug the refrigerator back in.
Vacation and Moving Tips
Short vacations:
* Leave refrigerator operating during vacations of 3 weeks or less.
* Use up all perishable items in refrigerator section.
* Wrap and store other items in the freezer.
* Turn off automatic ice maker, even if you will be gone just a few days.