Frigidaire FRS26ZXHW0 User manual

Versión en español ..................................... 2
Product Registration ................................... 2
Important Safety Instructions.................. 2-3
First Steps ................................................ 3-4
Energy Saving Ideas .................................. 5
Setting the Controls .................................... 5
Fresh Food Storage ................................... 6
Automatic Ice and Water Dispenser ....... 7-9
Care and Cleaning............................... 10-11
Removing the Handles and Doors .......... 12
Avoid Service Checklist ....................... 13-16
Normal Operating Sounds ....................... 16
Warranty (United States) .......................... 17
Service Information (Canada).................. 18
Warranty (Canada) ................................... 19
P/N 218931200 (9903)

2
Record the Model Number and Serial Number of this refrigerator in the space
providedbelow.These numbersarefound ontheserial plate,locatedon theceiling
oftherefrigerator compartment.
Model Number:
Serial Number:
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signedandreturnedto Frigidaire, or inCanada,FrigidaireCanada.
Versión en español
Si desea obtener una copia en español de este
Manual del Usuario, sírvase escribir la dirección
que se incluye a continuación. Solicite la P/N
2189931300.
Spanish Owner's Guides
Frigidaire Home Products
P.O. Box 212378
Augusta, GA 30917
Important Safety
Instructions For Your Safety
Donotstoreorusegasoline or other flammable vapors and liquids in thevicinity
ofthis,oranyotherappliance. Readproductlabelsforflammabilityandotherwarnings.
• Destroycarton,plasticbags,andanyexteriorwrappingmaterial immediately
aftertherefrigeratorisunpacked.Childrenshouldneverusetheseitemsforplay.
Cartons covered with rugs, bedspreads, plastic sheets, or stretch wrap may
becomeairtight chambers that can quickly cause suffocation.
• Remove all staples from the carton. Staples can cause severe cuts, and ruin
finishesif theycomeincontactwithotherappliances orfurniture.
• An empty, discarded ice box, refrigerator, or freezer is a very dangerous
attraction to children. Remove door of any appliance that is not in use,
even if it is being discarded.
•Refrigerator must be plugged into its own 115 Volt, 60 Hz, AC only
electrical outlet. The power cord of the appliance is equipped with a three-
prong grounding plug, for your protection against shock hazards. It must be
plugged directly into a properly grounded three-prong receptacle. The
receptacle must be installed in accordance with local codes and ordinances.
Consult a qualified electrician. DO NOT USE AN EXTENSION CORD OR AN
ADAPTER PLUG.
• If voltage varies by 10 percent or more, performance of your refrigerator may
beaffected.Operatingthe refrigerator withinsufficientpowercandamage the
compressor. Such damage is not covered under your warranty. If you suspect
your voltage is high or low, consult your power company for testing.
• Topreventtherefrigerator from beingturnedoffaccidentally,do not plugthe
unitintoan outlet controlledbyawall switch orpullcord.
• Do not pinch, knot, or bend the power cord in any manner.
Child Safety
Product Registration
© 1999 White Consolidated Industries, Inc.
Allrightsreserved.
Read all instructions before
using this refrigerator.
Avoid fire
hazard or electric shock. Do
not use an extension cord or
an adapter plug. Do not
remove any prong from
power cord.
ElectricalInformation
These guidelines must be followed to ensure that safety mechanisms in the
design of this refrigerator will operate properly.
Proper Disposal of Your
Refrigerator/Freezer
Riskofchildentrapment.
Childentrapment andsuffocationarenot
problems of the past. Junked or
abandonedrefrigeratorsorfreezers are
stilldangerous-eveniftheywillsitfor
"justafewdays." Ifyouaregettingridof
yourold refrigeratororfreezer,please
followinstructionsbelowtohelpprevent
accidents.
BEFORE YOU
THROW AWAY
YOUR OLD
REFRIGERATOR/
FREEZER:
* Remove doors.
* Leaveshelvesin
place,so
childrenmay
noteasilyclimb
inside.

3
Other Precautions
• Neverunplugthe refrigeratorbypulling onthepower cord.Alwaysgripthe plug
firmly,andpullstraight outfrom thereceptacle.
• Toavoidelectricalshock,unplugthe refrigerator before cleaning and before
replacingalightbulb. Note: TurningthecontroltoOFFturnsoffthecompressor,
butdoes notdisconnectpowertothe lightbulborotherelectricalcomponents.
• Donotoperatetherefrigeratorinthepresenceofexplosivefumes.
• Avoid contact with any moving parts of the automatic ice maker.
FirstSteps This Owner’s Guide provides specificoperatinginstructionsforyourmodel.Use
refrigeratoronlyasinstructedinthisOwner’sGuide. Beforestartingrefrigerator,
follow these important first steps:
Location
Installrefrigerator:
• nearagroundedelectricaloutlet.DONOTuseanextensioncordoranadapterplug.
• outofdirect sunlightandawayfrom range,dishwasher,orother heatsources,
ifpossible.
• onafloorthatislevelandstrongenoughtosupportafullyloadedrefrigerator.
• whereawater supply is available for automatic ice maker.
Installation
• Donotinstallrefrigeratorwheretemperaturewilldropbelow60°F(15°C),orrise
above110°F(43°C). Compressorwill notbeabletomaintainpropertemperatures.
• Inarecessedinstallation,allowan extra 1/2 inch (10-15 mm) on each side for
easeofinstallation.
• Ifthehingesideof theunitwill beplacedagainstawall, allowa1-3/4 inch(44
mm) space between wall and refrigerator to permit proper door swing.
Door Opening
For best use of drawers and freezer basket, refrigerator should be in a position
where both the refrigerator and freezer doors can be opened about 135°.
Leveling
• Refrigeratormustbeleveledwithallbottomcornersrestingfirmlyonasolidfloor.
Adjustfront rollerstolevel cabinetbothfront-to-rearandside-to-side. Keep
cabinetaslowaspossibleforstability. Neveradjustcabinetrollerssofrontislower
thanrear.
•Toadjustfront rollers: Open refrigeratorandfreezerdoors. Removetoegrill
bypullingitstraightout.Adjustrollersbyturningeachrolleradjustingboltwith
anadjustablewrench,asocketwrench,oranutdriveruntil refrigeratorislevel
andstable.Rearrollersarenotadjustable.
• Checkbothdoorstobesuresealstouchcabinetevenlyonallfoursides.
• Iffreezerdoorishigherthanrefrigeratordoor,raiserightcornerand/orlowerleft
corneruntildoorsalignacrosstopofcabinet.
• Ifrefrigeratordoorishigherthanfreezerdoor,raiseleftcornerand/orlowerright
corneruntildoorsalignacrosstopofcabinet.
•Toreplacetoe grill: Lineuptabswith holes,andpushgrill straighton.
Cleaning
• Wash the inside, all removable parts, and the outside with mild detergent and
warm water. Wipe dry. DO NOT USE HARSH CLEANERS ON THESE SURFACES.
• Do not use razor blades or other sharp instruments that can scratch appliance
surface, when removing adhesive labels. Any glue left from the tape or energy
label can be removed with a mixture of warm water and mild detergent, or touch
gluewithstickyside of tapealreadyremoved.
• DO NOT REMOVE SERIAL PLATE.
Important Safety
Instructions(continued)
AdjustingFrontRollers
ROLLER ADJUSTING
BOLT
ReplacingToeGrill

4
FirstSteps
(continued)
Connecting Ice Maker to Water Supply
Do Not Install Ice Maker Tubing Where Temperature May Fall
Below Freezing.
Check to be sure your water connection will comply with local plumbing codes.
Waterqualitydeterminesyouricequality.Itisbesttoconnecttheicemakertowater
thatisnotsoftened. Chemicals from a malfunctioning softener candamagetheice
maker. If the ice maker is connected to soft water, ensure that the softener is
maintainedandworkingproperly.
Theicemakerrequires a 1/4inch(6.4mm) copper water supplyline(withshut off)
fromyourhousehold water system.Allowenough tubingbehindyourrefrigeratorto
permitmovingouttocleanfloor.
Waterlinekit5308950117isavailable throughyour Dealerat extracharge.Thiskit
includes25 ft(7.6meters)of1/4inchdiameter coppertubing pluspartstoconnect
toyour coldwaterlineincludingasaddlevalve assembly.You willneedtopurchase
a1/4inchbrasscompressionnutandferrulefrom your local hardware or plumbing
store.
1. Turn ON water supply and flush out copper tubing. Turn OFF water supply
(Figure1).
2.Unplugrefrigerator(Figure1).
3.InstallWATERSUPPLYLINEasfollows (Figure 2):
 Slidebrass nut,thenferrule,ontocoppertubing
Pushendofcoppertubingasfarintothemetalwatervalvefittingasitwill
go(1/4inch).Slideferruleintofittingandthreadbrassnutontoinlet,
tightenfingertight plusone-halfturnwithwrench.
NOTE: Some models may have a cap on the valve. Unscrew the cap and
discard.
4. Secure copper tubing with STEEL CLAMP and screw to rear panel at location
show (Figure 3).
5.Routewater supply intocoilasshown (Figure 3).
NOTE: To prevent vibration noise and wear, leave a space between all
tubingandothersurfaces.
6. Turn on water supply and check all connections and leaks (Figure 3).
7.Plugrefrigeratorcordintowalloutlet(Figure3).
IMPORTANT
Iceproductionwillbegin when freezer reachesnormaloperatingtemperature.
Air in new plumbing lines may cause ice maker to cycle two or three times before
makingafulltrayofice.
Newplumbingmaycause ice to be discolored or have poor flavor. Discard ice made
duringthefirst24hours.Afterinstallation,ifyouwishtoshuttheicemakeroff,lift
shutoffarmuntilitclicksandlocksinUPposition.
Figure1
Copper water line from
household water supply
Brassnut
Ferrule
Figure2
Figure3

5
C05C0063
• Installtherefrigeratorinthemostcoolpartoftheroom,outofdirectsunlightand
awayfrom heatingductsor registers.Do notplacethe refrigeratornexttoheat-
producingappliancessuchasarange,ovenordishwasher.Ifthisis notpossible,
asectionofcabinetryor anaddedlayerofinsulation betweenthetwoappliances
willhelptherefrigeratoroperatemoreefficiently.
• Leveltherefrigeratorsothedoorsclosetightly.
• RefertothisOwner'sGuideforthesuggestedrefrigeratorsettings.
• Periodiccleaningofthecondenserwillhelptherefrigeratorrunmoreefficiently.
See Outside in the "Care and Cleaning" section.
• Do not overcrowd the refrigerator or block cold air vents. Doing so causes the
refrigeratortorunlonger and use moreenergy.Shelvesshouldnotbe lined with
aluminum foil, wax paper or paper toweling. Liners interfere with cold air
circulation,makingtherefrigeratorlessefficient,whichcouldcausefoodspoilage.
• Coverfoods andwipecontainersdrybeforeplacingthemintherefrigerator.This
cutsdownon moisturebuild-upinsidetheunit.
• Organize the refrigerator to reduce door openings. Remove as many items as
needed at one time and close the door as soon as possible.
Setting the Controls Cool Down Period
Toensure safefoodstorage,allowthe refrigeratortooperate withthedoorsclosed
foratleast8to12 hours before loading with food.
Refrigerator Control
• Therefrigeratorcontrolshouldbesetatthemidpointofthedialforatrialperiod
of24hours.
• After24hours,adjustthecontrolasneeded.Forcoldertemperatures,turnthedial
a notch toward COLDEST. For warmer temperatures, turn the dial a notch toward
COLD. Adjust temperatures by one increment at a time.
Freezer Control
• Thefreezer controlshouldbe setatthe midpointofthe dialforatrialperiodof
24hours.
• After24hours,adjustthecontrolasneeded.Forcoldertemperatures,turnthedial
a notch toward COLDEST. For warmer temperatures, turn the dial a notch toward
COLD. Adjust temperatures by one increment at a time.
Note: Whenfirstsettingthecontrolsor whenchanginga setting,wait24 hoursfor
thetemperatureto stabilizebeforemakingadditional changes.
Turning the freezer control may change temperatures in both compartments. For
example,ifthefreezer controlisturnedtoacoldersetting,therefrigeratorcontrol
may have to be adjusted to a warmer one. Turning the refrigerator control will
changeonly therefrigeratortemperature.
IMPORTANT: If the freezer control is turned to OFF, cooling stops in both
compartments.
Youmayhearthe"FrostFree"systemworking.Afancirculatesairintherefrigerator
andfreezercompartments.For good circulation and maintenanceofpropercooling
temperatures,donot block coldairventswith food items.Waterdraininginto the
defrostwaterpanand hissing sounds arenormalduringtheautomatic"Frost Free"
cycle.
Energy Saving Ideas
Refrigeratormidpoint
Freezermidpoint

6
Fresh Food Storage Shelf Adjustment
Refrigeratorshelvesareeasilyadjustedtosuitindividualneeds.Beforeadjusting
shelves,removeallfood.Theshippingclipswhichstabilizetheshelvesforshipping
may be removed and discarded.
Toadjustthecantilevershelves (shelvessupportedattherearoftherefrigerator),
lifttheback of theshelfupand out.Replaceshelfby inserting hooksatrearinto
slots.Lowerandlock into position. Somemodelshave Spillsafe glassshelves,
whichcatch andholdaccidentalspills.
Door Storage
Doorbinsandshelvesareprovided forconvenient storageof jars,bottlesandcans.
Itemsusedoftenareavailableforquickselection.
Thedoor binscanbemovedtosuitindividual needs.Removebinsbyliftingstraight
up.Placebinsinthedesiredpositionandloweroverthesupports.
The Dairy compartment is warmer than the general food storage section and is
intendedforshorttermstorage of cheese, spreads, orbutter.
Crisper
TheCrisperdrawer,locatedunderthebottomrefrigeratorshelf,isforstoringfruits
and vegetables. Most produce should be washed in clear water and drained before
placinginthisdrawer. Items withstrongodorsor high moisture shouldbewrapped
beforestoring.
The Humidity Control (some models) allows you to adjust the humidity within the
Crisperdrawer. Thiscan extendthelifeoffreshvegetableswhich keepbestinhigh
humidity. Leafy vegetables, however, keep best when stored with the Humidity
Control set on HIGHER, or in a drawer without a Humidity Control. This keeps
incoming air to a minimum and maintains maximum moisture content.
Meat Keeper
The Meat Keeper is located at the bottom of the refrigerator. The temperature in
this compartment can be made colder than the rest of the refrigerator compart-
ment by sliding the Chilled Air Control knob within the COLDEST or COLD range.
Meat will be partially frozen and may be kept fresh longer than if stored on a
refrigeratorshelf.
Beforeplacingitems in theMeatKeeper, follow thesestepstokeep themeatfresh:
1. Carefully handle meat with clean hands and always keep the compartment
clean.
2. Storemeatinitsoriginalwrapper.Ifnecessary,overwrapinplasticwraporfoil
topreventdrying.Wrap fish tightlytopreventodor transfer to otherfoods.
3. Ifspoilageever occurs,disinfectthecompartment withliquidchlorinebleach
followinglabel directions.Thenrinse withasolutionofbaking sodaandwater.
Rinsewithclearwateranddry.
Freezer Basket
A slide-out wire basket (some models have two) hangs below the bottom freezer
shelf.Thisbasket provides easyaccesstofrozen foodpackages.
Tall Storage Compartment (some models)
Ashelfisattachedtothefreezerwalljust below the ice server. This allows for
convenientstorageoftallitems placed vertically between the iceserverandthe
freezerwall.
Remove Shipping Clips
CantileverShelf
FRESH FRUITS & VEGETABLES
LOWER
FRUITS
HIGHER
HUMIDITY CONTROL
VEGETABLES
HumidityControl
ChilledAirControl
TallStorage
Compartment

7
Automatic Ice and
Water Dispenser
Theiceandwaterdispenseronthefreezerdoorconvenientlydispenseschilledwater,
and either ice cubes or crushed ice, depending on the model.
Tooperatethedispenser,slidetheknobtothe selectionofyour choiceandpress a
glass against the dispensing arm, as shown. Be sure to hold the glass as far up as
possibletocatchallice.Tostopdispensing,pullglassawayfrom dispensingarm.
Whendispensing ice,releasethe dispensingarmbeforetheglassisfull,but donot
removetheglass untiltheice has completelydispensed.
Asmallheatedareabeneaththedispenserfloorcatchesandevaporatessmallspills.
This drip tray is removable and dishwasher safe. Do not pour water or excess
cubes into this area because there is no drain.
Light
The dispenser has a light which can be turned on and off by sliding the knob to the
desiredposition.Thelightalsoturnsonautomaticallywheniceand/orwateris
dispensed.Replace light bulb with an appliance bulb of the same wattage.
How the Water Dispenser Works
The water tank is located behind the drawers in therefrigerator compartment. As
thewaterisdispensed,thetankisautomaticallyrefilled.Forproperoperationofthe
dispenser,thesupplywaterpressure must fallbetween 30psiand120psi.
Aftertherefrigeratorisinstalledandtheplumbing connectionsarecomplete,the
water tank should be filled by drawing one glass of water. It may take
about1-1/2minutes after depressing the dispenser arm beforewaterworksitsway
throughtheplumbingconnectionsandbeginstofillthisfirstglass.Drawanddiscard
7moreglasses to be sure that the tank and plumbing connections are rinsed of any
impurities.
To ensure fresh-tasting water, plan to use the dispenser every day. If the water
dispenser has not been used for a week or more, draw and discard 7-8 glasses to
freshenthe tanksupply.
How the Ice Dispenser Works
Theicemakerandicestoragebinarelocatedin the top left corner of the freezer
compartment.Aftertherefrigeratorisinstalledproperlyandhascooledforseveral
hours,theicemakercanbeginmakingice.Tobegin ice production, lower the wire
signal arm to the "down" or ON position. As cubes are made, they are stored in the
storagebin.Withnousageitwilltakeapproximately2daystofillthebin.However,
thedispensermaybeusedafterthefirstbatch of ice is made. The ice maker turns
offautomaticallywhentheicestoragebinisfull.
Because of new plumbing connections, the first production of ice cubes may be
discoloredorhave anoddflavor. Theseshouldbe discardeduntilthe cubesmadeare
freeofdiscolorationandtaste. Remember that water quality
determinesyour icequality. Itisbestto connecttheicemakertowaterthatis not
softened. Chemicals from a malfunctioning softener can damage the ice maker. If
icemakerisconnectedtosoftwater,ensurethesoftenerismaintainedandworking
properly.
Tostoptheicemaker,liftthewiresignalarmuntilitclicksandlocksinthe"up"or
OFFposition.
Wire
Signal Arm
Ice Maker
C05U0030 C05U0029
DispenserSelector
Pressglassagainstdispensingarm.

8
Do not use the ice
chute as a handle when removing
or replacing the ice storage bin.
Surfaces there may be sharp.
WARNING
Ice Dispenser Tips
1. Ice cubes stored too long may develop an odd flavor. Empty the container and
returnittothe proper position. Theicemakerwillthen produce more ice.
2. Occasionallyshakethecontainer tokeepiceseparated.
3. Ifthedispensingarm is pushedinformorethan 4 minutes, thedispensermotor
mayoverloadand stop.Theoverloadprotector willresetautomaticallyafter 3
or4minutes.If alarge quantityoficeisneededatonetime,itisbesttoremove
cubesdirectly fromtheicestoragebin.
4. Certain sounds are normal when the ice maker is operating. They are:
• Motor operation
• Ice being loosened from the tray
• Icedroppingintothestoragebin
• Running water
• Water valve opening or closing
For more information on these operations, see "Normal Operating Sounds."
5. Stop the ice maker when cleaning the freezer or for long vacations.
6. Iftheicemakeristobeturnedoffforalongperiodoftime,turnthewatersupply
valvetotheclosedposition.
Automatic Ice and
Water Dispenser
(continued)
Cleaning the Ice Dispenser
Cleanthedispenserandicestoragebinatregularintervals,particularlybeforeyou
takea vacationormove,oriftheice dispensersticks.
1. Stopiceproductionbylifting thewiresignal armtothe "up"orOFF position.
2. Removeicestoragebin by lifting upandout.Empty and carefully cleanthebin
with milddetergent.Donot submerge the bin whilecleaning.Rinsewithclear
water. Do not use harsh or abrasive cleaners. Allow ice bin to dry completely
beforereplacinginthefreezer.
3. Remove ice chips and clean the shelf and chute that supports the ice storage
bin.
4. Replace the ice storage bin. Lower the wire signal arm on the ice maker to the
"down" or ON position and the ice maker will resume production.
IMPORTANT: Whenremovingor replacingtheicebin, donotrotatethe augerin
theicebin.Iftheaugerisaccidentallyturned,youmustrealigntheaugerbyturning
itin90°turnsuntiltheicebinfitsintoplacewiththedrivemechanism.Forfurther
instruction,seethelabelontheicebucket.
Remove and empty the ice storage bin if:
1. Anextendedpowerfailure(onehourorlonger)causesicecubesintheicestorage
bin to melt and freeze together and jam the dispenser mechanism.
2. Theicedispenserisnotusedfrequently.Icecubeswillfreezetogetherinthebin
and jam the dispenser mechanism. Remove the ice storage bin and shake to
loosenthecubes.
NEVER use an ice pick or similar sharp instrument to break up the ice. This could
damage the ice storage bin and dispenser mechanism.
Repositioningthe Auger
AUGER
DRIVER
MECHANISM
DO NOT PUT FINGERS UP ICE CHUTE.
SURFACES THERE MAY BE SHARP.
PureSource Plus ™ Ice and Water Filter (some models)
NOTE: If you purchased a refrigerator with a PureSource Plus ™ Ice and
Water filter, please read the following use and care information. This ice and
waterfiltersystemfilterswatertoyouricemakerandwaterdispenser. Itislocated
in the upper right back corner of the fresh food compartment (see Figure 1 on the
following
page).
System Startup:
Water supply does not need to be turned off, however do not use ice and water
dispenserwhileinstallingfilter. RefertoFigure1asyoucompletetheseinstructions.
Thefiltercartridgehasalreadybeeninstalledinthefilterhousingatthefactory.Refer
tothe"HowTheDispenserWorks"sectiontoproperlyfillthesystemwithwater.

9
Automatic Ice and
Water Dispenser (continued)
Order new filter cartridges through the
dealer where you bought the
refrigerator, or contact the Frigidaire
Consumer Assistance Center at 1-800-
944-9044. It might be good to order
some filters when you first install your
refrigerator. Be sure to ask for the RC-
200 PureSource Plus™ replacement
cartridge.
The PureSource Plus™ RF-200 ice and
waterfilter system istested andcertified
by NSF International, the nationally
recognized and respected, not for profit,
certification organization for public
health safety. The PureSource Plus™
system is tested and certified to ANSI/
NSF Standards 42 and 53. See
performance data sheet for
specifications. This system should not be
used on water that is microbiologically
unsafe or with water of unknown quality
unless the water has been adequately
disinfected before or after traveling
through the filtration system.
Rated service flow- .37 GPM
Maximum Rated Pressure- 125 PSI
Maximum Operating Temp. - 100º
Figure1
Changing the Filter:
Waterqualityvariesthroughout the world. To ensure the highest possible water
quality,changewaterfilterevery6months,or200gallons. Also,iffilterhasbeen
inarefrigeratorthat has not been inuseforawhile(duringmoving for example),
changefilterbeforereinstallingrefrigerator. Notedispensersystemwillalsooperate
withoutfiltration(withfiltercartridgeremoved).
Tochangefilter:
RefertoFigure1asneeded.Itisnotnecessarytoturnthewatersupplyofftochange
thefilter.
1.Setice makerlever(wire signalarm)to theOFF(up)position.
2.Holdfilter cup firmly,andunscrewcounter clockwise (Figure 1).(Somewater
couldleakout asyou removecup.This isnormal.) Filtercartridgeshould come
downwith cup. Ifcartridgeremainsinhousing,pulldowngently,while twisting
filterbackandforth.
3. Empty cup of any substance.
4.Thelargeo-ring(Figure1)thatsealsthefiltersystemsetsintheo-ringgroove
downinsidethecup.Shouldtheo-ringfalloutduringfiltercartridgereplacement,
simplyplaceit backinthegroove priortoscrewingthe cupbackinplace. Ifthe
o-ring becomes damaged, you will need to order one from the Consumer
AssistanceCenter.
5.Discardoldfiltercartridge.
6.Removenewfiltercartridge frompackaging,and install.
7.Placefilter cartridgeincup.The endwiththe smallo-ringshouldbe up,out
ofthe cup.
8. Screw cup, with filter, back onto housing. DO NOT USE WRENCH TO REINSTALL
CUP.Filtercartridgewillself-alignascupistightened.Besurecupiscompletely
tightened with PureSource Plus™ logo facing outward. DO NOT TIGHTEN PAST
STOP.
9. Set ice maker lever on the ON (down) position.
10.Checkforleaks.Openrefrigeratordoor.Wipeanywaterdropsfromthefiltercup.
Runaglassofwater.Ifthereisaleak,unscrewfiltercup,andreinsertthefilter
cartridge.CheckplacementoflargeO-ring(seeFigure1).Reinstallfiltercup,
makingcertainitistightenedcompletely.
11.Tocondition filtersystemand purgeairfromwaterline, runseveralglassesof
waterthroughwaterdispenser.Thiswillalso assure that the purest water
possible is storedinwatertank.

10
Care and Cleaning Keepyourrefrigeratorandfreezercleantopreventodorbuild-up.Wipeupanyspills
immediately and clean both sections at least twice a year. Never use metallic
scouringpads,brushes,abrasivecleanersorstrongalkalinesolutionsonanysurface.
Do not wash any removable parts in a dishwasher.
Always unplug the power cord from the wall outlet before cleaning.
NOTE: Turning the control to OFF does not disconnect power to the controls, light
bulb,or otherelectrical components.
Inside
Washinsidesurfacesoftherefrigeratorandfreezerwithasolutionof2tablespoons
bakingsodain1 quart warmwater.Rinseand dry thoroughly. Besuretowringexcess
wateroutof spongeorclothbefore cleaningaroundthecontrols, lightbulb,orany
electricalparts.
Washremovablepartssuchasshelvesanddrawers with baking soda solution or mild
detergent and warm water. DO NOT USE HARSH CLEANERS ON THESE SURFACES.
Rinse and dry thoroughly. Clean the door gaskets with mild suds, rinse with clear
water and wipe dry. Do not use razor blades or other sharp instruments which can
scratchtheappliancesurfacewhen removingadhesivelabels. Anyglueleft fromthe
tape or energy label can be removed with a mixture of warm water and mild
detergent,or,touchthegluewiththestickysideoftapealreadyremoved.DONOT
REMOVE THE SERIAL PLATE.
Outside
Washthecabinetandhandleswithwarmwater and mild liquid detergent. Rinse well
and wipe dry with a clean soft cloth. Do not use commercial household cleaners,
ammonia,oralcoholtocleanhandles.
Removeanydustordirtfromthefrontofthetoegrillusingavacuumcleanerwith
itsdustingtoolattachment.Removethetoegrillbypullingitstraightout.Whilethe
grill is removed, vacuum the backside of the grill and wipe with a sudsy cloth or
sponge. Periodically clean the condenser (black tubes and wires beneath the
refrigerator,behindthetoegrill).Donotallowlintordusttoaccumulateonthecoils.
Insert a long handled brush or vacuum attachment between the two coils to bring
thelintforward.Toreplacethetoegrill,lineuptabswithholesandpushgrillstraight
on. Use caution when cleaning in the area of the coils. Surfaces
there may be sharp.
The air vents on the lower access panel at the rear of the refrigerator should be
cleanedperiodically.Cleantheventsbyusingavacuumcleanerwithitsdustingtool
attachment. When moving the refrigerator, pull straight out. Do not shift the
refrigeratorfromsidetosideasthismaytearorgougethefloorcovering.Becareful
not to move the refrigerator beyond plumbing connections.
Damp objects stick to cold
metalsurfaces. Donottouchrefrigerated
surfaces with wet or damp hands.
To avoid damage and help
the refrigerator run as efficiently as
possible, clean the condenser and air
ventsperiodically.
Air Vents on Lower Access Panel
Replacing the Light Bulb
To replace the light bulb in either compartment:
1. Unplugtherefrigerator.
2. Weargloves asprotectionagainstpossiblebrokenglass.
3. Replace old bulb with an appliance bulb of the same wattage.
4. Remembertoplugtherefrigeratorbackin.
Vacation and Moving Tips
Short vacations:
• Leaverefrigeratoroperating duringvacationsof3weeksorless.
• Useupallperishableitemsinrefrigeratorsection.
• Wrap and store other items in the freezer.
• Turn off automatic ice maker, even if you will be gone just a few days.