Frigidaire FFFW5100PW User manual

All about the
Installation
of your Washer
Important Safety Instructions..............................2-3
Installation Requirements ...................................4-6
Installation Instructions....................................7-10
Accessories.........................................................11
Notes.................................................................12
Français..............................................................13
Español ..............................................................25
TABLE OF CONTENTS
137621300A (1304)

2
IMPORTANT SAFETY INSTRUCTIONS
Shipping Hardware
Foam shipping support (under wash tub)
removed and stored
Shipping bolts and spacers removed from rear
of appliance and stored
Hole plugs (shipped in bag in drum) installed in
holes in backsheet
Leveling
Washer is level, side-to-side and front-to-back
Cabinet is setting solid on all corners
Water Supply
Use only new hoses and verify rubber sealing
washers are installed
HOT supply is connected to HOT inlet and
COLD supply is connected to COLD inlet
HOT and COLD water supply turned on
No leaks present at water supply connections
or appliance inlet connections -
recheck in 24 hours
Drain
Stand pipe or wall drain height minimum 24”
Anti-siphon disc (shipped in drum) installed on
drain hose
Drain hose secured in place with cable tie
(shipped in drum)
Electrical Power
 House power turned on
Washer plugged in
Final Checks
 Installation Instructions and Use and Care
Guide read thoroughly
Door locks and water enters drum when cycle
starts
Registration card sent in
Installation Checklist
Definitions
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury
or death.
Recognize safety symbols, words
and labels
Safety items throughout this manual are labeled with
a WARNING or CAUTION based on the risk type as
described below:
IMPORTANT
IMPORTANT indicates installation, operation or
maintenance information which is important but not
hazard-related.
WARNING
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
WARNING
Please read all instructions before using this washer.
CAUTION
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
DANGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury.

3
IMPORTANT SAFETY INSTRUCTIONS
NOTE
The electrical service to the washer must conform with
local codes and ordinances and the latest edition of the
National Electrical Code, ANSI/NFPA 70, or in Canada,
the Canadian Electrical Code C22.1 part 1.
NOTE
Hoses are not included with washer purchase. See
“Accessories” section for various inlet hose kits to fit
your specific installation.
WARNING
FIRE HAZARD
For your safety the information in this manual must be
followed to minimize the risk of fire or explosion or to
prevent property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
WARNING
SUFFOCATION HAZARD
Destroy the carton and plastic bags after the washer is
unpacked. Children might use them for play. Cartons
covered with rugs, bedspreads, or plastic sheets can
become airtight chambers causing suffocation. Place
all materials in a garbage container or make materials
inaccessible to children.
IMPORTANT
The instructions in this manual and all other literature
included with this washer are not meant to cover
every possible condition and situation that may occur.
Good safe practice and caution MUST be applied when
installing, operating and maintaining any appliance.
Maximum benefits and enjoyment are achieved
when all the Safety and Operating Instructions are
understood and practiced as a routine with your
laundering tasks.
CAUTION
EXCESSIVE WEIGHT HAZARD
To avoid back or other injury, have more than one
person move or lift the washer.
Save these instructions for future reference.
Tools and materials needed for installation:
Adjustable
pliers
Adjustable
wrench
3/8” or 10 mm
box wrench
OR OR AND AND
Ratchet and
socket set
Carpenter’s level
Inlet hose (x2)

4
INSTALLATION REQUIREMENTS
NOTE
Drain hose attached to the washer can reach a 74 in.
(188 cm) high standpipe. For higher standpipe, use
hose P/N 137098000, available from an authorized
parts distributor.
NOTE
GFI (Ground Fault Interrupter) receptacle is not
required.
NOTE
Because of potentially inconsistent voltage capabilities,
the use of this washer with power created by gas
powered generators, solar powered generators, wind
powered generators or any other generator other than
the local utility company is not recommended.
CIRCUIT - Individual, properly polarized and grounded
15 amp. branch circuit fused with 15 amp. time delay
fuse or circuit breaker.
POWER SUPPLY - 2 wire, with ground, 120 volt single
phase, 60 Hz, Alternating Current.
OUTLET RECEPTACLE - Properly grounded 3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position.
Grounding type
Grounding type
wa
wa
ll receptacl
ll receptacle
Po
Po
wer cord with
wer cord with
3-prong
3-prong
gr
gr
ounded plug
ounded plug
Do not,
Do not,
under
under
an
an
y cir
y cir
cumstances,
cumstances,
cut,
cut,
remo
remo
ve
ve,
or b
or b
ypass th
ypass the
gr
gr
ounding pr
ounding pr
ong.
ong.
96”
(244cm)
max.
24”
(61cm)
min.
Drain system requirements
1Drain capable of eliminating 17 gals (64.3 L) per
minute.
2A standpipe diameter of 1-1/4 in. (3.18 cm)
minimum.
3The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244 cm)
Water supply requirements
Hot and cold water faucets MUST be installed within hose
length of your washer’s water inlet. The faucets MUST
be 3/4 inch (1.9 cm) with threading for laundry hose
connection. Water pressure MUST be between 30 and
120 psi. Pressure difference between hot and cold cannot
be more than 10 psi. Your water department can advise
you of your water pressure.
1The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electrical shock by a path of least
resistance for electrical current.
2Since your washer is equipped with a power supply
cord having an equipment-grounding conductor
and a grounding plug, the plug MUST be plugged
into an appropriate, copper wired receptacle that is
properly installed and grounded in accordance with
all local codes and ordinances or in the absence
of local codes, with the National Electrical Codes,
ANSI/NFPA 70 (latest edition). If in doubt, call a
licensed electrician. DO NOT cut off or alter the
grounding prong on the power supply cord. In
situations where a two-slot receptacle is present,
it is the owner’s responsibility to have a licensed
electrician replace it with a properly grounded three
prong grounding type receptacle.
Ground requirements
Electrical system requirements
WARNING
ELECTRICAL SHOCK HAZARD
Improper connection of the equipment grounding
conductor can result in a risk of electrical shock. Check
with a licensed electrician if you are in doubt as to
whether the appliance is properly grounded.

5
INSTALLATION REQUIREMENTS
MINIMUM INSTALLATION CLEARANCES - Inches (cm)
SIDES REAR TOP FRONT
Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a
Under-
Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a
Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm) 1” (2.5 cm)
0”
(0cm)
0”
(0cm)
1”
(2.5cm)
0”
(0cm)
Installation in a Recess or Closet
If washer and dryer are installed in the same closet,
door ventilation is required: A minimum of 120 square
inches (774.2 cm²) of opening, equally divided at the top
and bottom of the door, is required. Louvered openings
should be located 3 inches (7.6 cm) from bottom and
top of door. Air openings are required to be unobstructed
when a door is installed. A louvered door with equivalent
air openings for the full length of the door is acceptable.
60 sq. in.
(387.1cm²)
3”
(7.6cm)
60 sq. in.
(387.1cm²)
3”
(7.6cm)
closet door
Clearance requirements
IMPORTANT
DO NOT INSTALL YOUR WASHER:
1 In an area exposed to dripping water or outside
weather conditions. The ambient temperature
should never be below 60° F (15.6° C) to
maximize detergent effectiveness.
2 In an area (garage or garage-type building)
where gasoline or other flammables (including
automobiles) are kept or stored.
3 On carpet. Floor MUST be solid with a maximum
slope of 1 inch (2.5 cm). To minimize vibration
or movement, reinforcement of the floor may be
necessary.

6
Washer Dimensions
*Connection of water inlet hose on steam dryer adds 3/4 in. (2 cm) to installation depth.
1Power supply cord length on washer approximately 60 inches (152.5 cm).
2Drain hose length on washer approximately 59 inches (150 cm).
3Power supply cord length on gas dryer approximately 60 inches (152.5 cm).
gas supply
pipe on rear
of gas unit
water supply
connection on
rear of unit
power cord
on rear of
unit1
floor line
71.5”
(182 cm)
37”
(94 cm)
39”
(99 cm)
27.0”
(68.5 cm)
electrical
supply on
rear of unit3
centerline
height for
rear vent
drain hose on
rear of unit2
30.3” (77 cm)*
to front of closed door
51.4” (131 cm)*
to clear open door
floor line
floor line
30.3” (77 cm)*
to front of closed door
freestand washer
on floor
washer mounted on
optional pedestal
51.4” (131 cm)*
to clear open door
36.0”
(91.5 cm)
51.25”
(130 cm)
power cord on
rear of unit1
drain hose on
rear of unit2
water supply
connection on
rear of unit
27.0”
(68.5 cm)
INSTALLATION REQUIREMENTS

7
1Temporarily remove door tape.
2Open washer door and remove everything from the
drum.
3Close door and reapply door tape.
4Using a rug, blanket or piece of cardboard to
protect the floor, carefully lay the washer on it’s
back.
Removing foam packaging
5Remove styrofoam base and shipping plug and set
them aside.
6Carefully return the washer to an upright position.
7Carefully move the washer to within 4 feet (1 m) of
its final location.
WARNING
SUFFOCATION HAZARD
Destroy the carton and plastic bags after the washer is
unpacked. Children might use them for play. Cartons
covered with rugs, bedspreads, or plastic sheets can
become airtight chambers causing suffocation. Place
all materials in a garbage container or make materials
inaccessible to children.
CAUTION
EXCESSIVE WEIGHT HAZARD
To avoid back or other injury, have more than one
person move or lift the washer.
IMPORTANT
Save styrofoam base and shipping plug for use to help
prevent washer damage during any future moves.
INSTALLATION INSTRUCTIONS

8
INSTALLATION INSTRUCTIONS
x 4
4 HOLE PLUGS
(IN BAG)
Locate 4 hole plugs in the small bag supplied
with washer instruction guides. Insert them in
the holes in washer back panel.
Removing shipping hardware
Installing hole plugs
Remove all of the following:
4 SPACERS
4 BOLTS
2 P CLAMPS
x 4
x 2
x 4
4 SPACERS
4 BOLTS
2 P CLAMPS
IMPORTANT
Save all shipping bolts and spacers for future use. If
the washer is to be transported at a later date, the
shipping hardware must be reinstalled to help prevent
shipping damage.
NOTE
Rubber expansion material on spacers may need
time to relax before they can be easily pulled through
shipping hole.

9
INSTALLATION INSTRUCTIONS
ab
cd
raise lower
a
e
f
g
b
cd
Leveling your washer
Excessive noise and vibration can be prevented by
properly leveling the washer.
1For free standing installation and with the washer
within 4 feet (1 m) of its final location, place a level
on top of the washer.
2Use adjustable pliers to adjust the leveling legs so
the washer is level front-to-rear and side-to-side,
and stable corner-to-corner.
3Press down on alternate corners and sides and feel
for the slightest movement. Adjust the appropriate
leg(s) so the washer sits solidly on the floor on
ALL four legs. Keep the leveling leg extension at a
minimum for best performance of the washer.
Connecting inlet water
COLD
HOT
NOTE
For pedestal installations, see additional installation
instructions included with the pedestal.
NOTE
Hoses are not included with washer purchase. See
“Accessories” section for various inlet hose kits to fit
your specific installation.
1Run some water from the hot and cold faucets
to flush the water lines and remove particles
that might clog the water valve screens and to
determine which faucet is hot and which is cold
supply.
2Connect the HOT inlet hose to the HOT inlet
connection on the washer and the COLD inlet
hose to the COLD inlet connection on the washer.
Tighten by hand until snug. Then tighten each
supply connection another 2/3 turn with pliers.
Do not cross thread or over-tighten these
connections.
3Connect the HOT inlet hose to the HOT water
supply and the COLD inlet hose to the COLD water
supply. Tighten by hand until snug. Then tighten
each supply connection another 2/3 turn with
pliers. Do not bend, kink or pinch water inlet
hoses.
4Turn on the water and check for leaks.
RUBBER WASHERS
MUST BE PRESENT USE ONLY
NEW HOSES

10
INSTALLATION INSTRUCTIONS
CABLE TIE
ANTI-SIPHON
DISC
SLIDE DISC
TO HERE
Grounding type
Grounding type
wa
wa
ll receptacl
ll receptacle
Po
Po
wer cord with
wer cord with
3-prong
3-prong
gr
gr
ounded plug
ounded plug
Do not,
Do not,
under
under
an
an
y cir
y cir
cumstances,
cumstances,
cut,
cut,
remo
remo
ve
ve,
or b
or b
ypass th
ypass the
gr
gr
ounding pr
ounding pr
ong.
ong.
Connecting drain and electrical
1Locate the anti-siphon ring shipped with your
washer. Place it over the end of the drain hose and
slide it past the first ring of “accordion” ribs.
2Form a “U” shape on the end of the drain hose
with the hose pointed toward the drain. Place the
formed end in a laundry tub or a standpipe and
secure the drain hose with the cable tie (provided
in the enclosure package) to the standpipe, inlet
hose, laundry tub, etc. so the hose does not pull
out from the force of the water.
3Plug the power cord into a grounded outlet.
4Turn on the power at a circuit breaker/fuse box.
5Carefully slide the washer to its final position.
Recheck for level and rock corners for stability.
Remove and discard door tape.
6Read the Use & Care Guide provided with the
washer. It contains valuable and helpful information
that will save you time and money.
7Run the washer through a complete cycle, checking
for water leaks and proper operation.
8If you have any questions during initial operation,
please review the “Service Prevention Checklist” in
your Use & Care Guide before calling for service.
9Place these instructions in a location near the
washer for future reference.
IMPORTANT
Check to ensure the power is off at a circuit breaker/
fuse box before plugging the power cord into an outlet.
NOTE
A wiring diagram and technical data sheet are located
under the washer top panel, on top of the detergent
dispenser housing.
NOTE
The standpipe inside diameter must be 1-1/4” (3.2 cm)
minimum. There must be an air gap around the drain
hose in the standpipe. A snug hose fit can cause a
siphoning action.