Frigidaire Full Size Tumble Action Washers User manual

Installation
Instructions
Full Size Tumble Action Washers
Before beginning installation, carefully read these instructions. This will simplify the
installation and ensure the washer is installed correctly and safely. Leave theseinstructions
near the washer after installation for future reference.
NOTE:The electrical service to the washer must conform with local codes and ordinances
and the latest edition of the National Electrical Code, ANSI/NFPA 70 or in Canada, CSA
C22.1 Canadian Electrical Code Part 1. Contents
SUBJECT PAGE
Pre-Installation Requirements 2
Electrical Requirements 2
Grounding Requirements 2
Water Supply Requirements 2
Drain Requirements 2
Rough-In Dimensions 3
Location OfYour Washer 4
Unpacking 4
Installation 5
Replacement Parts 5
Printed in U.S.A. P/N131803200(9811)
Foryoursafetytheinformationin
this manual must be followed to minimize the
risk of fire or explosion or to prevent property
damage, personal injury or loss of life.
- Do not store or use gasoline or other
flammable vapors and liquid in the vicinity of
this or any other appliance.
- WHATTO DO IFYOU SMELL GAS
·Do not try to light any appliance.
·Do not touch any electrical switch; do not
use any phone in your building.
·Clear the room, building or area of all
occupants.
·Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppliers
instructions.
·If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.

2
PRE-INSTALLATION REQUIREMENTS
Tools Required for Installation:
1. 1/4 in. nut driver
2. 3/8 in. socket with ratchet.
3. 3/8 in. open end wrench.
4. 7/16 in. socket with ratchet.
5. 9/16 in. open end wrench.
6. Channel-lock adjustable pliers.
7. Carpenter’s level.
ELECTRICAL REQUIREMENTS
CIRCUIT -Individual,properly polarizedand grounded
15 amp. branch circuit fused with 15 amp. time delay
fuse or circuit breaker.
POWER SUPPLY -2wire, withground,120 volt,single
phase, 60 Hz, Alternating Current.
OUTLET RECEPTACLE -Properlygrounded3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position.
GROUNDING REQUIREMENTS
Improper connectionoftheequipment grounding
conductorcan resultina risk ofelectricalshock.Check
with a licensed electrician if you are in doubt as to
whether the appliance is properly grounded.
1. The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electrical shock by a path of least
resistance for electrical current.
2. Since your washer is equipped with a power
supply cord having an equipment-grounding
conductor and a grounding plug, the plug MUST
be plugged into an appropriate, copper wired
receptaclethatisproperly installedandgrounded
inaccordancewith all local codesandordinances
orintheabsence of local codes,withthe National
Electrical Codes, ANSI/NFPA 70 (latest edition).
If in doubt, call a licensed electrician. DO NOT
cut off or alter the grounding prong on the power
supply cord. In situations where a two-slot
receptacle is present, it is the owner’s
responsibility to have a licensed electrician
replace it with a properly grounded three prong
grounding type receptacle.
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets MUST be installed within
42 inches (107 cm) of your washer’s water inlet.The
faucets MUST be 3/4 inch (1.9 cm) garden hose type
so inlet hoses can be connected. Water pressure
MUST be between 10 and 120 pounds per square
inch (maximum unbalance pressure, hot vs. cold, 10
psi.) Your water department can advise you of your
water pressure.The hot water temperature should be
about120degreesF(49 degrees C).
DRAIN REQUIREMENTS
1. Drain capable of eliminating 17 gals (64.3 L) per
minute.
2. A standpipe diameter of 1-1/4 in. (3.18 cm)
minimum.
3. The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244 cm)
NOTE:
Drain hose attached to the washer can reach a
58 in. (147 cm) high standpipe. For higher
standpipe use hose P/N 131461201, available
from an authorized parts distributor. If drain is
less than 24 in. (61 cm), install a siphon break
kit, available at your local hardware store.
24 in.
(61 cm)
Min.

3
ROUGH-IN DIMENSIONS
UNDER COUNTER INSTALLATION
If an under counter* installation is desired, the washer MUST have a top sheet kit installed, P/N 131445600.
Kit is available from an authorized parts distributor.
*Custom sized countertop is required.
º º
º
º

4
SPACER
BOLT
"P" CLAMP
LOCATION OF YOUR WASHER
DO NOT INSTALL YOUR WASHER:
1. In an area exposed to dripping water or outside
weather conditions. The ambient temperature
should never be below 60 degrees F (15.6
degrees C) for proper washer operation.
2. In an area where it will come in contact with
curtains or drapes.
3. In anarea(garage or garage-typebuilding)where
gasoline of other flammables are kept or stored
(including automobiles).
4. On carpet. Floor MUST be solid with a maximum
slope of 1/2 in. per foot (1.27 cm per 30.5 cm).To
ensure vibration or movement does not occur,
reinforcement of the floor may be necessary.
IMPORTANT
MINIMUMINSTALLATION CLEARANCES
When installed in alcove or closet:
Sides, Rear = 0 in. (0 cm)
Top = 0 in. (0 cm) Front Console Model
Top = 15 in. (38.1 cm) Rear Console Model
When installed in closet: Front = 1 in. (2.54 cm)
Closet door ventilation required: 2 louvered openings
each60in2(387cm2),3in.(7.6cm)fromtopandbottom
ofdoor.
UNPACKING
1. Cuttheshipping carton alongthedotted linealong
the base of the unit.
2. While in the carton carefully lay the washer on its
back side.
3. Remove the styrofoam base.
4. Carefully return the washer to an upright position
and remove the carton.
5. Carefully movethe washerto within 4feet(122cm)
of the final location.
6. Remove the following from the back side of the
washer: 4 bolts,
4 yellow plastic spacers,
4 metal "P" clamps.
7. Remove the service panel from the front of the
washer.
8. Removethe4 nutsand6 large washersthat attach
the 2 yellow shipping braces to the drum and the
base. Lift up on the drum and remove the braces
(a yellow ribbon surrounds the items to be
removed).Thesebracesmustbe removedtoallow
the power supply cord to be released from the
shipping ring.
9. Remove the large styrofoam block located under
the drum. Lift up on the drum, tilt the base of the
foam block inwards toward the rear of the washer
until free, then pull it out.
10. Remove and discard the yellow ribbon and label
from the front of the washer.
11. From the rear of the washer, carefully pull out the
power supply cord through the hole in the
backsheet.
12. Replace the service panel and screws.
NOTE: Ifthewasher is to betransportedat a later
date,theshippingsupport hardware must
be reinstalled to prevent shipping
damage. Retain the hardware in the
plastic bag provided.

5
Cable
Tie
REPLACEMENT PARTS
If replacements parts are needed for your washer,
contactthesourcewhereyoupurchasedyourwasher
or call 1-800-944-9044 for the Frigidaire Company
Authorized Parts Distributor nearest you.
Destroy the carton and plastic bags
afterthewasherisunpacked.Children might usethem
for play. Cartons covered with rugs, bedspreads, or
plasticsheetscanbecomeairtight chambers causing
suffocation.Place all materials in a garbagecontainer
or make materials inaccessible to children.
The instructions in this manual and all
otherliteratureincluded withthiswasherarenot meant
to cover every possible condition and situation that
may occur. Good safe practice and cautionMUST be
appliedwheninstalling, operatingand maintainingany
appliance.
Maximum benefits and enjoyment are achieved
when all the Safety and Operating instructions are
understood and practiced as a routine with your
laundering tasks.
Cable Tie
Cable
Tie
6. Plug the power cord into a grounded outlet.
NOTE: Check to ensure the power is off at a
circuit breaker/fuse box before plugging
the power cord into an outlet.
7. Turn on the power at a circuit breaker/fuse box.
8. Read the Operating Instructions and Owner’s
Guide provided with the washer. They contain
valuable and helpful information that will save you
time and money.
9. Run the washer through a complete cycle. Check
for water leaks and proper operation.
10. If your washer does not operate, please review
the “Avoid Service Checklist” in your Owner’s
Guide before calling for service.
11. Place these instructions in a location near the
washer for future reference.
NOTE: A wiring diagram is located inside the washer
on the service panel.
INSTALLATION
1. Run some water from the
hotandcold faucetstoflush
the water lines and remove
particles that might clog up
the water valve screens.
2. Connectthe inlethoseends
tothe HOTandCOLDwater
faucets tightly by hand,
thentighten another2/3 turn
withpliers.Turnthewateron
and check for leaks.
NOTE: Useonlynewhosesprovidedwiththis unit.
3. Carefully move the washer to its final location.
Rollers on the rear of the washer allow for easy
movement in undercounter installations. Gently
lift up on the front of the washer and slide back.
NOTE: Lifting up more than 1/8" will engage the
rearlegs.Donot usethedispenser drawer
or door to lift washer.
4. With the washer in its final position, place a level
on top of the washer (if an undercounter
installation,norockingofthe washershouldexist).
Adjustthefrontlevelinglegsup or downtoensure
the washer is resting solid. Turn the lock nuts on
each leg up towards the base of the washer and
snug with a wrench.
NOTE: Keep the leg extension at a minimum to
prevent excessive vibration. The farther
out the legs are extended the more the
washer will vibrate.
The washer is designed to operate resting on its
rear rollers. If the floor is not level or is damaged,
the rear leveling legs may have to be extended.
Forundercounter installations, rearlegadjustment
is accessible through the front service panel.
5. Form a U shape on the end of the drain hose with
the hose pointed toward the drain. Place in a
laundrytubor standpipe andsecurewith thecable
tie provided in the enclosure package.
NOTE: If the drain hose is placed in a standpipe
without forming a U shape, a siphoning
action could occur. There must be an air
gap around the drain hose. A snug hose
fit can also cause a siphoning action.

[DO NOT PRINT
P/N 131803200 — English Page 6 left intentionally blank.]