Frymaster RE E4 Series User manual

Frymaster, a member of the Commercial Food Equipment Service Association, recommends
using CFESA Certified Technicians.
24-Hour Service Hotline [phone] FEB 2009
www.frymaster.com E-mail: [email protected]
RE SERIES
E4ELECTRIC FRYERS
Installation & Operation Manual
*8196149*

NOTICE
IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS ENODIS
EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED
DIRECTLY FROM FRYMASTER DEAN, OR ANY OF ITS AUTHORIZED SERVICE CENTERS,
AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS
WARRANTY WILL BE VOID. FURTHER, FRYMASTER DEAN AND ITS AFFILIATES WILL NOT BE
LIABLE FOR ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH
ARISE DIRECTLY OR INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF
ANY MODIFIED PART AND/OR PART RECEIVED FROM AN UNAUTHORIZED SERVICE CENTER.
NOTICE
This appliance is intended for professional use only and is to be operated by qualified
personnel only. A Frymaster Dean Factory Authorized Service Center (FASC) or other qualified
professional should perform installation, maintenance, and repairs. Installation, maintenance,
or repairs by unqualified personnel may void the manufacturer’s warranty. See Chapter 1 of
this manual for definitions of qualified personnel.
NOTICE
This equipment must be installed in accordance with the appropriate national and local codes of
the country and/or region in which the appliance is installed. See NATIONAL CODE
REQUIREMENTS in Chapter 2 of this manual for specifics.
NOTICE TO U.S. CUSTOMERS
This equipment is to be installed in compliance with the basic plumbing code of the Building
Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation
Manual of the U.S. Food and Drug Administration.
NOTICE
Drawings and photos used in this manual are intended to illustrate operational, cleaning and
technical procedures and may not conform to onsite management operational procedures.
NOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS
U.S.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) This device must accept
any interference received, including interference that may cause undesired operation. While
this device is a verified Class A device, it has been shown to meet the Class B limits.
CANADA
This digital apparatus does not exceed the Class A or B limits for radio noise emissions as set
out by the ICES-003 standard of the Canadian Department of Communications.
Cet appareil numerique n’emet pas de bruits radioelectriques depassany les limites de classe A
et B prescrites dans la norme NMB-003 edictee par le Ministre des Communcations du Canada.
DANGER
Improper installation, adjustment, maintenance or service, and unauthorized alterations or
modifications can cause property damage, injury, or death. Read the installation, operating,
and service instructions thoroughly before installing or servicing this equipment.
DANGER

The front ledge of this appliance is not a step! Do not stand on the appliance. Serious injury
can result from slips or contact with the hot cooking oil/shortening.
DANGER
Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any
other appliance.
DANGER
The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container
at the end of frying operations each day. Some food particles can spontaneously combust if left
soaking in certain shortening material.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is present to seal
the joint between the fry vessels. Banging fry baskets on the strip to dislodge shortening will
distort the strip, adversely affecting its fit. It is designed for a tight fit and should only be
removed for cleaning.
DANGER
Adequate means must be provided to limit the movement of this appliance without depending
on or transmitting stress to the electrical conduit. A restraint kit is provided with the fryer. If
the restraint kit is missing contact your local Frymaster Factory Authorized Service Center
(FASC) for part number 826-0900.
DANGER
Prior to movement, testing, maintenance and any repair on your Frymaster fryer, disconnect all
electrical power from the fryer.

i
RE Series E4Electric Fryers
Installation and Operation Manual
TABLE OF CONTENTS
CHAPTER 1: Introduction
1.1 General Information ..........................................................................................................1-1
1.2 Safety Information.............................................................................................................1-1
1.3 Computer Information.......................................................................................................1-2
1.4 European Community (CE) Specific Information.............................................................1-2
1.5 Installation, Operating and Service Personnel ..................................................................1-2
1.6 Definitions.........................................................................................................................1-2
1.7 Shipping Damage Claim Procedure .................................................................................1-3
1.8 Service Information...........................................................................................................1-3
CHAPTER 2: Installation Instructions
2.1 General Installation Requirements....................................................................................2-1
2.2 Power Requirements..........................................................................................................2-3
2.3 Positioning the Fryer Station.............................................................................................2-3
CHAPTER 3: Operating Instructions
3.1 Setup and Shutdown Procedures.......................................................................................3-2
3.2 Controllers.........................................................................................................................3-3
CHAPTER 4: Filtration Instructions
4.1 Draining and Manual Filtering..........................................................................................4-1
4.2 Preparing the Built-In Filtration System for Use ..............................................................4-2
4.3 Operation of the Filter.......................................................................................................4-5
4.4 Disassembly and Reassembly of the Magnasol Filter.......................................................4-7
4.5 Draining and Disposing of Waste Oil ...............................................................................4-8
CHAPTER 5: Preventive Maintenance
5.1 Cleaning the Fryer.............................................................................................................5-1
5.1.1 Daily Checks and Service..................................................................................................5-1
5.1.3 Weekly Checks and Service..............................................................................................5-2
5.1.4 Boiling Out the Frypot .....................................................................................................5-2
5.2 Monthly Checks and Service.............................................................................................5-3
5.2 Calibration of Solid State (Analog) Controller Knob .......................................................5-3
5.3 Annual/Periodic System Inspection ..................................................................................5-3
CHAPTER 6: Operator Troubleshooting
6.1 Introduction ......................................................................................................................6-1
6.2 Troubleshooting.................................................................................................................6-2
6.2.1 Troubleshooting Controller and Heating Problems ..........................................................6-2
6.2.2 Troubleshooting Error Messages and Display Problems .................................................. 6-4
6.2.3 Troubleshooting the Basket Lift........................................................................................6-7
6.2.4 Troubleshooting the Built-In Filtration System ................................................................6-7

1-1
RE SERIES E4 ELECTRIC FRYERS
CHAPTER 1: INTRODUCTION
1.1 General
Read the instructions in this manual thoroughly before attempting to operate this equipment. This
manual covers all configurations of FPRE14, FPRE17, and FPRE22 models. The fryers in this
model family have most parts in common, and when discussed as a group, will be referred to as “RE
Series Electric” fryers.
Although similar in appearance to the Pro Series Electric family of Common Electric fryers, the RE
Series Electric fryers feature a significantly different rotating element with an enhanced design.
Other features, including the deep cold-zones, open frypots and filtration system remain essentially
unchanged. Control options include multi-product cooking computers (standard) or optional digital
and analog controllers. Fryers in this series come in full- or split-pot arrangements, and can be
purchased as single units or grouped in batteries of up to six fryers.
1.2 Safety Information
Before attempting to operate your unit, read the instructions in this manual thoroughly.
Throughout this manual, you will find notations enclosed in double-bordered boxes similar to the
one below.
DANGER
Hot cooking oil causes severe burns. Never attempt to move a fryer containing hot
oil or to transfer hot oil from one container to another.
CAUTION boxes contain information about actions or conditions that may cause or result in a
malfunction of your system.
WARNING boxes contain information about actions or conditions that may cause or result in
damage to your system, and which may cause your system to malfunction.
DANGER boxes contain information about actions or conditions that may cause or result in
injury to personnel, and which may cause damage to your system and/or cause your system to
malfunction.
Fryers in this series are equipped with the following automatic safety features:
1. Two high-temperature detection features shut off power to the elements should the temperature
controls fail.
2. A safety switch built into the drain valve prevents the elements from heating with the drain valve
even partially open.

1-2
1.3 Computer Information
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. While this device is a verified Class A device, it has been
shown to meet the Class B limits. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
the equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at their own expense.
The user is cautioned that any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
If necessary, the user should consult the dealer or an experienced radio and television technician for
additional suggestions.
The user may find the following booklet prepared by the Federal Communications Commission
helpful: "How to Identify and Resolve Radio-TV Interference Problems". This booklet is available
from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.
1.4 European Community (CE) Specific Information
The European Community (CE) has established certain specific standards regarding equipment of
this type. Whenever a difference exists between CE and non-CE standards, the information or
instructions concerned are identified by means of shadowed boxes similar to the one below.
CE Standard
Example of box used to distinguish CE and
Non-CE specific information.
1.5 Installation, Operating, and Service Personnel
Operating information for Frymaster equipment has been prepared for use by qualified and/or
authorized personnel only, as defined in Section 1.6. All installation and service on Frymaster
equipment must be performed by qualified, certified, licensed, and/or authorized installation
or service personnel, as defined in Section 1.6.
1.6 Definitions
QUALIFIED AND/OR AUTHORIZED OPERATING PERSONNEL
Qualified/authorized operating personnel are those who have carefully read the information in this
manual and have familiarized themselves with the equipment functions, or who have had previous
experience with the operation of the equipment covered in this manual.

1-3
QUALIFIED INSTALLATION PERSONNEL
Qualified installation personnel are individuals, firms, corporations, and/or companies which, either
in person or through a representative, are engaged in and are responsible for the installation of
electrical appliances. Qualified personnel must be experienced in such work, be familiar with all
electrical precautions involved, and have complied with all requirements of applicable national and
local codes.
QUALIFIED SERVICE PERSONNEL
Qualified service personnel are those who are familiar with Frymaster equipment and who have been
authorized by Frymaster, L.L.C. to perform service on the equipment. All authorized service
personnel are required to be equipped with a complete set of service and parts manuals, and to stock
a minimum amount of parts for Frymaster equipment. A list of Frymaster Factory Authorized
Service Centers (FASC) is included with the fryer when shipped from the factory. Failure to use
qualified service personnel will void the Frymaster warranty on your equipment.
1.7 Shipping Damage Claim Procedure
What to do if your equipment arrives damaged:
Please note that this equipment was carefully inspected and packed by skilled personnel before
leaving the factory. Frymaster does not assume responsibility for damage or loss incurred in transit.
The freight company assumes full responsibility for safe delivery upon acceptance of the equipment.
1. File Claim for Damages Immediately—Regardless of extent of damage.
2. Visible Loss or Damage—Be sure this is noted on the freight bill or express receipt and is signed
by the person making the delivery.
3. Concealed Loss or Damage—If damage is unnoticed until equipment is unpacked, notify the
freight company or carrier immediately and file a concealed damage claim. This should be done
within 15 days of date of delivery. Be sure to retain container for inspection.
1.8 Service Information
For non-routine maintenance or repairs, or for service information, contact your local Frymaster
Authorized Service Center (FASC). Service information may also be obtained by calling the
Frymaster Technical Services Department (1-800-24FRYER) or by e-mail at
[email protected].The following information will be needed in order to assist you efficiently:
Model Number_________________________
Serial Number _________________________
Voltage ______________________________
Nature of the Problem___________________
____________________________________
____________________________________
RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE.

2-1
RE SERIES E4 ELECTRIC FRYERS
CHAPTER 2: INSTALLATION INSTRUCTIONS
2.1 General
Proper installation is essential for the safe, efficient, trouble-free operation of this appliance.
Qualified, licensed, and/or authorized installation or service personnel, as defined in Section
1.6 of this manual, should perform all installation and service on Frymaster equipment.
Failure to use qualified, licensed, and/or authorized installation or service personnel (as
defined in Section 1.6 of this manual) to install or otherwise service this equipment will void
the Frymaster warranty and may result in damage to the equipment or injury to personnel.
Where conflicts exist between instructions and information in this manual and local or
national codes or regulations, installation and operation shall comply with the codes or
regulations in force in the country in which the equipment is installed.
Service may be obtained by contacting your local Factory Authorized Service Center.
NOTICE
All fryers shipped without factory supplied cords and plug assemblies must be
hardwired using flexible conduit to the terminal block located on the rear of the fryer.
These fryers should be wired to NEC specifications. Hardwired units must include
installation of restraint devices.
DANGER
Adequate means must be provided to limit the movement of this appliance without
depending on or transmitting stress to the electrical conduit. A restraint kit is
provided with the fryer. If the restraint kit is missing contact your local Frymaster
Factory Authorized Service Center (FASC) for part number 826-0900.
NOTICE
If this equipment is wired directly into the electrical power supply, a means for
disconnection from the supply having a contact separation of at least 3-mm in all
poles must be incorporated in the fixed wiring.
NOTICE
This equipment must be positioned so that the plug is accessible unless other
means for disconnection from the power supply (e.g., a circuit breaker) is provided.
NOTICE
If this appliance is permanently connected to fixed wiring, it must be connected by
means of copper wires having a temperature rating of not less than 167°F (75°C).
NOTICE
If the electrical power supply cord is damaged, it must be replaced by a Frymaster
Dean Factory Authorized Service Center technician or a similarly qualified person in
order to avoid a hazard.

2-2
DANGER
This appliance must be connected to a power supply having the same voltage and
phase as specified on the rating plate located on the inside of the appliance door.
DANGER
All wiring connections for this appliance must be made in accordance with the wiring
diagram(s) furnished with the appliance. Refer to the wiring diagram(s) affixed to the
inside of the appliance door when installing or servicing this equipment.
DANGER
Frymaster appliances equipped with legs are for stationary installations. Appliances
fitted with legs must be lifted during movement to avoid damage to the appliance
and bodily injury. For movable installations, optional equipment casters must be
used. Questions? Call 1-800-551-8633.
DANGER
Do not attach an apron drainboard to a single fryer. The fryer may become unstable,
tip over and cause injury. The appliance area must be kept free and clear of
combustible material at all times.
In the event of a power failure, the fryer(s) will automatically shut down. If this occurs, turn the
power switch OFF. Do not attempt to start the fryer(s) until power is restored.
This appliance must be kept free and clear of combustible material, except that it may be installed on
combustible floors.
A clearance of 6 inches (15cm) must be provided at both sides and back adjacent to combustible
construction. A minimum of 24 inches (61cm) should be provided at the front of the equipment for
servicing and proper operation.
WARNING
Do not block the area around the base or under the fryers.
2.1.2 Electrical Grounding Requirements
All electrically operated appliances must be grounded in accordance with all applicable national and
local codes, and, where applicable, CE codes. All units (cord connected or permanently connected)
should be connected to a grounded power supply system. A wiring diagram is located on the inside
of the fryer door. Refer to the rating plate on the inside of the fryer door for proper voltages.
2.1.3 Australian Requirements
To be installed in accordance with AS 5601 / AG 601, local authority, gas, electricity, and any other
relevant statutory regulations.

2-3
2.2 Power Requirements
Three (3) Phase Requirements
MODEL VOLTAGE
WIRE
SERVICE
MINIMUM WIRE
SIZE
AWG (mm)
AMPS
(per leg)
FPRE14 208 3 6 (4.11) 39
FPRE14 240 3 6 (4.11) 34
FPRE14 480 3 8 (2.59) 17
FPRE14 220/380 4 6 (4.11) 21
FPRE14 240/415 4 6 (4.11) 20
FPRE14 230/400 4 6 (4.11) 21
FPRE17 208 3 6 (4.11) 48
FPRE17 240 3 6 (4.11) 41
FPRE17 480 3 6 (4.11) 21
FPRE17 220/380 4 6 (4.11) 26
FPRE17 240/415 4 6 (4.11) 24
FPRE17 230/400 4 6 (4.11) 25
FPRE22 208 3 4 (5.19) 61
FPRE22 240 3 4 (5.19) 53
FPRE22 480 3 6 (4.11) 27
FPRE22 220/380 4 6 (4.11) 34
FPRE22 240/415 4 6 (4.11) 31
FPRE22 230/400 4 6 (4.11) 32
Single Phase Requirements
MODEL VOLTAGE
WIRE
SERVICE
MINIMUM WIRE
SIZE
AWG (mm)
AMPS
(per leg)
FPRE14 208 2 3 (5.83) 68
FPRE14 240 2 4 (5.19) 59
FPRE14 480 2 8 (3.26) 30
NOTICE
If this appliance is permanently connected to fixed wiring, it must be connected by
means of copper wires having a temperature rating of not less than 167°F (75°C).
DANGER
This appliance must be connected to a power supply having the same voltage and
phase as specified on the rating plate located on the inside of the appliance door.
DANGER
All wiring connections for this appliance must be made in accordance with the
wiring diagram(s) furnished with the appliance. Refer to the wiring diagram(s)
affixed to the inside of the appliance door when installing or servicing this
equipment.
2.3 After Fryers Are Positioned At the Frying Station
DANGER
No structural material on the fryer should be altered or removed to accommodate
placement of the fryer under a hood. Questions? Call the Frymaster Dean Service
Hotline at 1-800-551-8633.

2-4
1. Once the fryer has been positioned at the frying station, use a carpenter’s level placed across the
top of the frypot to verify that the unit is level, both side-to-side and front-to-back.
To level fryers equipped with legs, the bottom of the legs can be screwed out up to one inch for
leveling. Legs should also be adjusted so that the fryer(s) are at the proper height in the frying station.
For fryers equipped with casters, there are no built-in leveling devices. The floor where the
fryers are installed must be level.
When the fryer is leveled in its final position, install the restraints provided with the unit to limit
its movement so that it does not depend on or transmit stress to the electrical conduit or
connection. Install the restraints in accordance with the provided instructions (see illustration
below). If the restraints are disconnected for service or other reasons, they must be reconnected
before the fryer is used.
DANGER
Adequate means must be provided to limit the movement of this appliance without
depending on or transmitting stress to the electrical conduit. A restraint kit is
provided with the fryer. If the restraint kit is missing contact your local Frymaster
Factory Authorized Service Center (FASC) for part number 826-0900.
NOTE:If you need to relocate a fryer installed with legs, remove all weight from each leg
before moving. If a leg becomes damaged, contact your service agent for immediate repair or
replacement.
DANGER
Hot oil can cause severe burns. Avoid contact. Under all circumstances, oil must be
removed from the fryer before attempting to move it to avoid oil spills, falls and
severe burns. This fryer may tip and cause personal injury if not secured in a
stationary position.
2. Close fryer drain-valve(s) and fill frypot with water to the bottom oil level line.
3. Boil out frypot(s) in accordance with the instructions in Section 5.1.3 of this manual.
4. Drain, clean, and fill frypot(s) with cooking oil. (See Equipment Setup and Shutdown
Procedures in Chapter 3.)

3–1
RE SERIES E4 ELECTRIC FRYERS
CHAPTER 3: OPERATING INSTRUCTIONS
FINDING YOUR WAY AROUND THE FPRE SERIES E4ELECTRIC FRYER
TYPICAL CONFIGURATION (FPRE217 SHOWN)
NOTE: The appearance of your fryer may differ slightly from that
shown depending upon the configuration and date of manufacture.
Tilt Housing Basket Hangers
Lift Rods
Elements
Top Cap
Bezel
Control Panel
(CMIII.5 Computer shown)
Fryer Identification
Data Labels (Model
and Serial Number
)
Drain and Filter Handles FootPrint Pro Built-
in Filtration Unit Drain
Filter Pan
Fuse
Power Switch

3–2
3.1 Equipment Setup and Shutdown Procedures
Setup
DANGER
Never operate the appliance with an empty frypot. The frypot must be filled to the fill
line with water, oil or shortening before energizing the elements. Failure to do so
will result in irreparable damage to the elements and may cause a fire.
DANGER
Remove all drops of water from the frypot before filling with oil. Failure to do so will
cause spattering of hot liquid when the oil is heated to cooking temperature.
1. Fill the frypot with oil to the bottom OIL LEVEL line located on the rear of the frypot. This will
allow for oil expansion as heat is applied. Do not fill cold oil any higher than the bottom line;
overflow may occur as heat expands the oil.
NOTE: If solid shortening is used, first raise the elements, then pack the shortening into the
bottom of the frypot. Lower the elements, and then pack the shortening around and over the
elements. It may be necessary to add shortening to bring the level up to the proper mark after the
packed shortening has melted.
DANGER
Never set a complete block of solid shortening on top of the heating elements.
When using solid shortening, always pre-melt the shortening before adding it to the
frypot. If the shortening is not pre-melted, it must be packed down into the bottom of
the frypot and between the elements, and the fryer must be started in the melt-cycle
mode.
Never cancel the melt-cycle mode when using solid shortening. Doing so will result
in damage to the elements and increase the potential for a flash fire.
2. Ensure that the power cord(s) is/are plugged into the appropriate receptacle(s). Verify that the
face of the plug is flush with the outlet plate, with no portion of the prongs visible.
3. Ensure that the power is switched on. Some models are equipped with a master switch located
behind the fryer door cabinet on the front panel of the component box, next to the fuse. See page
3-1. standby or off is displayed on the computer.
4. Ensure that the computer / controller is switched ON.
5. Ensure that the oil level is at the top OIL LEVEL line when the oil is at its cooking temperature.
It may be necessary to add oil or shortening to bring the level up to the proper mark, after it has
reached cooking temperature.
Shutdown
1. Turn the fryer off.
2. Filter the cooking oil and clean the fryers (See Chapters 4 and 5).
3. Place the frypot covers on the frypots.

3–3
3.2 Controllers
This fryer may be equipped with any of the following controllers:
Computer Magic III.5 (CM III.5)
Basket Lift Timer
Digital Controller
SOLID STATE
Solid State (Analog) Controller
CAUTION
If this is the first time the fryer is being used after installation, refer to the frypot Boil-Out Procedure
on Page 5-2.
Refer to the separate Frymaster Fryer Controllers User’s Manual furnished with your fryer for the
specific controller operating instructions.
Refer to Chapter 4 of this manual for operating instructions for the built-in filtration system.

4-1
RE SERIES E4 ELECTRIC FRYERS
CHAPTER 4: FILTRATION INSTRUCTIONS
WARNING
The on-site supervisor is responsible for ensuring that operators are made aware of
the inherent hazards of operating a hot oil filtering system, particularly the aspects
of oil filtration, draining and cleaning procedures.
4.1 Draining and Manual Filtering
DANGER
Draining and filtering of oil must be accomplished with care to avoid the possibility
of a serious burn caused by careless handling. The oil to be filtered is at or near
350°F (177°C). Ensure all hoses are connected properly and drain handles are in
their proper position before operating any switches or valves. Wear all appropriate
safety equipment when draining and filtering oil.
DANGER
Allow oil to cool to 100°F (38°C) before draining into an appropriate container for
disposal.
DANGER
Do not drain more than one frypot at a time into the built-in filtration unit to avoid
overflow and spillage of hot oil.
DANGER
When draining oil into a disposal unit or portable filter unit, do not fill above the
maximum fill line located on the container.
If your fryer is not equipped with a built-in filtration system, the oil must be drained into another
suitable METAL container. (For safe, convenient draining and disposal of used oil or shortening,
Frymaster recommends using the Frymaster Shortening Disposal Unit (SDU). The SDU is available
through your local distributor.)
1. Turn the fryer power switch to the OFF position. Screw the drainpipe (provided with your fryer)
into the drain valve. Make sure the drainpipe is firmly screwed into the drain valve and that the
opening is pointing down.
2. Position a metal container with a sealable cover under the drainpipe. The metal container must
be able to withstand the heat of the oil and hold hot liquids. If you intend to reuse the oil or
shortening, Frymaster recommends that a Frymaster filter cone holder and filter cone be used
when a filter machine is not available. If you are using a Frymaster filter cone holder, be sure
that the cone holder rests securely on the metal container.

4-2
3. Open the drain valve slowly to avoid splattering. If the drain valve becomes clogged with food
particles, use the Fryer’s Friend (poker-like tool) to clear the blockage.
DANGER
NEVER attempt to clear a clogged drain valve from the front of the valve! Hot oil will
rush out creating the potential for severe burns.
DO NOT hammer on the drain valve with the cleanout rod or other objects. Damage
to the ball inside will result in leaks and will void the Frymaster warranty.
4. After draining the oil, clean all food particles and residual oil from the frypot. BE CAREFUL,
this material may still cause severe burns if it comes in contact with bare skin.
5. Close the drain valve securely and fill the frypot with clean, filtered or fresh oil or solid
shortening to the bottom OIL-LEVEL line.
DANGER
When using solid shortening, pack the shortening down into the bottom of the
frypot. DO NOT operate the fryer with a solid block of shortening sitting in the upper
portion of the frypot. This will cause damage to the frypot and may cause a flash
fire.
4.2 Preparing the Built-In Filtration System for Use
The FootPrint Pro filtration system allows the oil in one frypot to be safely and efficiently filtered
while the other frypots in a battery remain in operation. The FootPrint Pro filtration system is
available in three different configurations:
•Filter Paper – includes crumb tray, large hold-down ring, and metal filter screen.
•Filter Pad – includes crumb tray, small hold-down ring, and metal filter screen.
•Magnasol Filter – includes crumb tray and Magnasol filter assembly.
Section 4.2.1 covers preparation of the Filter Paper and Filter Pad configurations for use. Refer to
Section 4.2.2 for instructions on preparing the Magnasol Filter configuration for use. Operation of
all three configurations is the same and is covered in section 4.3. Disassembly and reassembly of the
Magnasol filter is covered in section 4.4.

4-3
4.2.1 Preparation for Use with Filter Paper or Filter Pad
1. Pull the filter pan out from the cabinet
and remove the crumb tray, hold-down
ring, filter paper and filter screen. (See
Figure 1) Clean all components with a
solution of detergent and hot water, then
dry thoroughly.
The filter pan is equipped with rollers in
rails, much like a kitchen drawer. The
pan may be removed for cleaning or to
gain access to interior components by
lifting the front of the pan to disengage
the front rollers, then pulling it forward
until the rear rollers clear the rails. The
pan cover must not be removed except
for cleaning, interior access, or to allow
a shortening disposal unit (SDU) to be
positioned under the drain. If using an
SDU built before January 2004 see
instructions on page 4-8.
2. Inspect the filter pan connection fitting
to ensure that both O-rings are in good
condition. (See Figure 2)
3. Then in reverse order, place the metal
filter screen in the center of the bottom
of the pan, then lay a sheet of filter paper
on top of the screen, overlapping on all
sides. (See Figure 1) If using a filter
pad, ensure the rough side of the pad is
up and lay the pad over the screen,
making sure that the pad is in between
the embossed ridges of the filter pan.
4. Position the hold-down ring over the
filter paper and lower the ring into the
pan, allowing the paper to rest on the
sides of the filter pan. (See Figure 3)
Screen
Filter Paper
Hold-Down Ring
Crumb Tray
Figure 1
Figure 2
Figure 3
Inspect the filter
connection fitting
O-rings.

4-4
5. When the hold-down ring is in position,
if using filter paper, sprinkle one packet
of filter powder evenly over the paper.
(See Figure 4)
If using a filter pad, position the hold
down ring on top of the pad. DO NOT
use filter powder with the pad.
Figure 4
6. Replace the crumb tray in the filter pan, then push the filter pan back into the fryer, positioning it
under the drain.
4.2.2 Preparation for Use with the Magnasol Filter Assembly
1. Pull the filter pan out from the cabinet
and remove the crumb tray and
Magnasol filter assembly. (See Figure
5)
The filter pan is equipped with rollers in
rails, much like a kitchen drawer. The
pan may be removed for cleaning or to
gain access to interior components by
lifting the front of the pan to disengage
the front rollers, then pulling it forward
until the rear rollers clear the rails. The
pan cover must not be removed except
for cleaning, interior access, or to allow
a shortening disposal unit (SDU) to be
positioned under the drain.
NOTE: Refer to Section 4.4 for
instructions on how to disassemble and
reassemble the Magnasol filter screen
assembly.
2. Inspect the fitting on the bottom of the
Magnasol filter assembly to ensure that
the O-ring is present and in good
condition. (See Figure 6)
3. Inspect the filter pan connection fitting
to ensure that both O-rings are present
and in good condition. (See Figure 7)
Figure 5
Figure 6
Figure 7
Inspect the filter
screen O-ring.
Inspect the filter
connection fitting
O-rings.

4-5
4. Replace the Magnasol filter assembly in the filter pan, ensuring that the fitting on the bottom of
the assembly is securely seated in the port in the bottom of the pan. Sprinkle one packet of the
Magnasol XL filter powder evenly over the screen.
5. Replace the crumb tray, then push the filter pan back into the fryer, positioning it all the way to
the back of the cabinet.
4.3 Operation of the Filter
DANGER
Draining and filtering of oil must be accomplished with care to avoid the possibility
of a serious burn caused by careless handling. The oil to be filtered is at or near
350°F (177°C). Ensure drain handles are in their proper position before operating
any switches or valves. Wear all appropriate safety equipment when draining and
filtering oil.
DANGER
NEVER attempt to drain oil from the fryer with the burners lit! Doing so will cause
irreparable damage to the frypot and may cause a flash fire. Doing so will also void
the Frymaster warranty.
1. Ensure that the filter is prepared. See
Sec. 4.2.
2. Make sure the oil is at operating
temperature.
3. Turn the fryer power OFF. Drain the
frypot into the filter pan by rotating the
valves 90º. If necessary, use the Fryer's
Friend clean-out rod to clear the drain
from inside the frypot.
DANGER
Do not drain more than one frypot at a time into the built-in filtration unit to avoid
overflow and spillage of hot oil.
DANGER
NEVER attempt to clear a clogged drain valve from the front of the valve! Hot oil will
rush out creating the potential for severe burns.
DO NOT hammer on the drain valve with the cleanout rod or other objects. Damage
to the ball inside will result in leaks and will void the Frymaster warranty.
Open drain valves
by rotating 90º.

4-6
4. After the oil has drained from the frypot,
turn the filter handle to the ON position
to start the pump and begin the filtering
process. There may be a slight delay
before the pump activates.
5. The filter pump draws the oil through the filter medium and circulates it back up to and through
the frypot during a 5-minute process called polishing. Polishing cleans the oil by trapping solid
particles in the filter medium.
6. After the oil is filtered (about 5 minutes), close the drain valve and allow the fryer to refill. Let
the filter pump run 10 to 12 seconds after the oil begins to bubble. Turn the filter off.
WARNING
The filter pump is equipped with a manual reset switch in case the filter motor
overheats or an electrical fault occurs. If this switch trips, turn off power to the filter
system and allow the pump motor to cool 20 minutes before attempting to reset the
switch (see photo below).
Filter Pump Reset Switch
7. Lower the elements into the frypot and reinstall the basket support rack.
Turn filter handle to
the ON position