FujiFilm DR-ID 1200PB User manual

897N120972A
This Operation Manual describes details on how to operate the power box
DR-ID 1200PB and cautions to be observed when operating it.
Please read the Operation Manual, System Operation Manual and other manuals
for the related products before actually operating the power box.
After reading this manual, store it nearby the power box so that you can see
it whenever necessary.
For Safe Operation
System
Conguration
(Product Overview)
Basic Operation
Daily Inspection and
Maintenance
Appendix
Maintenance and
Inspection
Power Box
DR-ID 1200PB
Operation Manual
2nd Edition : April 2016

ii DR-ID 1200PB Operation Manual 897N120972A

iii
DR-ID 1200PB Operation Manual 897N120972A
Introduction
The power box DR-ID 1200PB is a device which supplies power to the at panel sensor and
connects between the at panel sensor, image processing unit and control cabinet.
The power box DR-ID 1200PB is an optional item of DR-ID 1200.
This Operation Manual includes descriptions of matters necessary when using the DR-ID 1200PB,
such as the equipment overview, operation procedures and precautions to observe, as well as daily
inspections and maintenance.
Accompanying documents were originally drafted in the English language.
Installation may only be conducted by authorized service personal.
CAUTIONS
1. No part or all of this manual may be reproduced in any form without prior permission.
2. The information contained in this manual may be subject to change without prior notice.
3. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
installation, relocation, remodeling, maintenance, and repair performed by other than dealers
specied by FUJIFILM Corporation.
4. FUJIFILM Corporation shall not be liable for malfunctions and damages of FUJIFILM
Corporation products due to products of other manufacturers not supplied by FUJIFILM
Corporation.
5. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
remodeling, maintenance, and repair using repair parts other than those specied by
FUJIFILM Corporation.
6. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
negligence of precautions and operating methods contained in this manual.
7. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from use
under environment conditions outside the range of using conditions for this product such as
power supply, installation environment, etc. contained in this manual.
8. FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from
natural disasters such as res, earthquakes, oods, lightning, etc.
This system is classied as a medical device under EC Directive 93/42/EEC.
Process waste correctly, as stipulated by local law or any regulations that apply.
Caution : Rx Only in the United States (Federal law restricts this device to sale by or on the order
of a physician.)
Trademarks
All company names and product names described in this manual are the trademarks or registered
trademarks of FUJIFILM Corporation or their respective holders.
Windows is the registered trademark of US Microsoft Corporation in the U.S.A. and other countries.
Copyright © 2015-2016 FUJIFILM Corporation. All rights reserved.

iv DR-ID 1200PB Operation Manual 897N120972A

v
DR-ID 1200PB Operation Manual 897N120972A
Contents
Introduction...........................................................................................................................iii
Chapter 1 For Safe Operation
1.1 Safety ...................................................................................................................... 1-1
Chapter 2 System Conguration (Product Overview)
2.1 DR-ID 1200PB......................................................................................................... 2-1
2.1.1 System Conguration ..............................................................................................2-1
2.2 Unit Names and the Functions................................................................................ 2-2
2.3 Locations of Labels and Signs ................................................................................ 2-2
2.3.1 Locations of Labels..................................................................................................2-2
2.3.2 Safety and Other Symbols.......................................................................................2-3
2.3.3 Symboles de sécurité et autres ...............................................................................2-3
Chapter 3 Basic Operation
3.1 Preparing the Flat Panel Sensor ............................................................................. 3-1
3.1.1 Number of the Connectable Flat Panel Sensors .....................................................3-1
3.1.2 Connecting/Disconnecting the Flat Panel Sensor Connector..................................3-1
3.1.3
Changing the Direction of the Flat Panel Sensor Connector ........................................ 3-2
3.1.4 Checking the Connection between the Flat Panel Sensor and the Connector........3-2
3.2 Starting Up and Shutting Down the DR-ID 1200PB ................................................ 3-2
3.2.1 Starting Up the DR-ID 1200PB................................................................................3-2
3.2.2 Performing an Exposure .........................................................................................3-3
3.2.3 Shutting Down the DR-ID 1200PB...........................................................................3-3
Chapter 4 Daily Inspection and Maintenance
4.1 Daily User Inspection and Maintenance......................................................................4-1
4.1.1 Periodical Inspection................................................................................................4-1
Appendix A Specications
A.1 Specications ..........................................................................................................A-1
A.1.1 Power Supply Conditions........................................................................................ A-1
A.1.2 Environmental Conditions....................................................................................... A-1
A.2 External View and Weight .......................................................................................A-2
A.2.1 DR-ID 1200PB ........................................................................................................ A-2
Appendix O Use of Optional Items
O.1 Optional Items ....................................................................................................... O-1
O.1.1 Retaining bracket for PB ............................................................................................ O-1
Maintenance and Inspection

vi DR-ID 1200PB Operation Manual 897N120972A

1-1
For Safe Operation
1
DR-ID 1200PB Operation Manual 897N120972A
Chapter 1 For Safe Operation
1.1 Safety
Before using the DR-ID 1200PB, read this section thoroughly to ensure that you use the product
properly.
Electric Shock Warnings and Cautions
WARNING
The power supply to this device is AC100 to 240V.
To avoid electric shocks, users should always take the following precautions:
● Do not open any covers when it is not necessary.
● Install the equipment in a location where it will not be exposed to water.
● Check that the equipment is securely earthed.
● Check that all of the cables are completely and securely connected.
WARNING
Do not touch the patient’s body while touching the control cabinet and the image processing
unit. Otherwise, the patient may receive an electric shock.
WARNING
Do not use a multiple tap connector or extension cable for powering the devices constituting
the system. Otherwise, re or electric shock may occur due to the electrical load exceeding the
allowable limit.
WARNING
Observe the following precautions when using the cables.
● Do not touch the plug and connector with wet hands. Otherwise, electric shock may result,
causing death or severe injury.
● Hold the plug or connector when removing the cable.
Pulling the cable or carrying by holding it may damage the cable, causing re or electric shock.
● Do not damage or remodel the cable.
Do not place a heavy object on the cable or lay it under the at panel sensor. Do not step on,
pull, forcibly bend, or bundle the cable. Otherwise, re or electric shock may result.
● Do not use the at panel sensor for the radiographic examination stand if its cable becomes
overloaded. Otherwise, the cable may be damaged, causing re or electric shock.
WARNING
Do not turn on the system with dew condensation on the at panel sensor. Otherwise, re or
electric shock may result.
WARNING
Do not use the equipment in a location where metal particles could come into the equipment.
This may cause an electric shock.

1-2
For Safe Operation
1
DR-ID 1200PB Operation Manual 897N120972A
WARNING
Do not disassemble or remodel the equipment. Otherwise, re or electric shock may result.
Keep away from the parts inside the product, which may cause electric shock. If you touch
them accidentally, death or severe injury may result.
WARNING
Do not hit or drop the equipment or subject it to severe shock. Otherwise, the equipment may
be damaged. If the damaged equipment is used, re or electric shock may result.
WARNING
Make sure to use the optional parts recommended by us. Failure to use the optional parts
recommended by us may result in damage to the equipment and/or electric shock and injury.
CAUTIONS
As the cables of the equipment are long, be careful not to entangle the cables during use.
Also, be careful not to trip over the cables. Falls could result in injury.
CAUTIONS
Follow the specied procedure when turning off the equipment. Otherwise, the at panel
sensor could be damaged by thermal shock.
CAUTIONS
Do not store magnetic media near the DR system and control cabinet. Otherwise, magnetism
generated by the equipment may cause the data to be lost.
CAUTIONS
Keep the equipment away from patient’s body uids, chemicals, water, etc.
Otherwise, it may become damaged, causing re or electric shock.
Explosion Warnings
WARNING
Because this equipment is not explosion-proof, do not use combustible and explosive gases
near the equipment.
WARNING
Flammable gasses may stay in the room after disinfection. If you turn the system on just after
disinfection, ensure that the room is well ventilated before powering on the system.

1-3
For Safe Operation
1
DR-ID 1200PB Operation Manual 897N120972A
Warnings for Abnormalities
WARNING
If any of the following occurs, immediately turn off the power of each unit, unplug the power
cable from the outlet, and then contact our ofcial dealer or FUJIFILM Representative.
● When smoke, strange odor, or abnormal sound is present.
● When a foreign object (such as a metal object) or liquid enters the product.
● When the equipment is dropped or hit and is damaged.
Avertissements relatifs aux anomalies
AVERTISSEMENT
Si l’une des conditions répertoriées ci-après se produit, mettez immédiatement chaque unité
hors tension, débranchez le cordon d’alimentation de la prise secteur, puis contactez notre
revendeur agréé ou notre représentant FUJIFILM.
● En cas de présence de fumée, d’une odeur étrange ou d’un bruit anormal.
● En cas de pénétration d’un corps étranger (comme un objet métallique) ou d’un liquide dans
le produit.
● En cas d’endommagement de l’équipement suite à une chute ou à un impact.
Installation Precautions
CAUTIONS
Do not install the equipment in a location with the following conditions.
● Where the temperature changes sharply.
● Close to heat sources such as a heater.
● Where the equipment may be exposed to water due to water leakage or ingress.
● Where corrosive gas may be generated.
● Where there is excessive dust.
● Where the equipment is subject to frequent or excessive vibration/shock.
● Where the equipment is exposed to direct sunlight.
● Where there is no ventilator.
CAUTIONS
Do not install the power box in a place where it may be stepped on or kicked inadvertently.
CAUTIONS
Do not install the device in a high place. If the cable is pulled, the device may fall down, leading
to damage to the device or personal injury.
CAUTIONS
For veterinary or mobile applications, contact our ofcial dealer or FUJIFILM Representative.
CAUTIONS/ATTENTION
Do not place any object in a place where removal of the power cable is prevented.
Ne placez aucun objet à un emplacement gênant le débranchement du câble d’alimentation.

1-4
For Safe Operation
1
DR-ID 1200PB Operation Manual 897N120972A
CAUTIONS
To ensure optimal image quality, it is recommended that you do not use the at panel sensor
near devices (motor, transformer, switching supply, etc.) that generate electromagnetic noise.
Connection Instructions
WARNING
Make sure that the devices to be connected to the equipment are authorized for connection.
Precautions on External Network Connection
CAUTIONS
When a setting of the network to which the equipment is connected has been changed,
check that the change does not affect the system operation and take measures if necessary.
The setting change may include the following:
● Change of connection destination
● Addition of devices
● Removal of devices
● Update of devices
● Upgrade of devices
Warnings and Cautions on Network
WARNING
Make sure to use the optional parts and networks recommended by us. Failure to use the
optional parts and networks recommended by us may result in damage to the equipment and/
or electric shock and injury.
CAUTIONS
Connect to the Ethernet Network of 100BASE-TX or 10BASE-T prescribed in the IEEE standard 802.3.
Do not connect telephone lines to LAN connector. Only UTP-type straight LAN cables of 4-pair
Category 5 cable (CAT 5E) or higher are appropriate for connection to this connector.
CAUTIONS
After connecting this system to the network with other systems,conrm that the other systems
are not affected. If they are affected, take countermeasures such as network separation.
CAUTIONS
If the length of the network cable to be used is 2m or more, be sure to use a HUB.