Fujitsu ARUX12TLAV2 User manual

PART No. 9380242000
ARUX12TLAV2
ARUX18TLAV2
ARUX24TLAV2
ARUX30TLAV2
ARUX36TLAV2
ARUX48TLAV2
ARUX60TLAV2
OPERATION MANUAL
INDOOR UNIT (Duct type)
Keep this manual for future reference
MODE D’EMPLOI
UNITÉ INTÉRIEURE (type conduit)
Conservez ce manuel pour pour toute référence ultérieure.
MANUAL DE FUNCIONAMIENTO
UNIDAD INTERIOR (Tipo conducto)
Conserve este manual para posibles consultas futuras.
EnglishFrançaisEspañol
9380242000-01_OM_3L.indb 19380242000-01_OM_3L.indb 1 2021/4/22 13:39:012021/4/22 13:39:01

En-1
OPERATION MANUAL
PART No. 9380242000
VRF system indoor unit (Duct type)
SAFETY PRECAUTIONS
●Before using this product, read these “SAFETY PRECAUTIONS” thor-
oughly and operate in the correct way.
●The instructions in this section all relate to safety; be sure to maintain
safe operating conditions.
●“WARNING” and “CAUTION” have the following meanings in these
instructions:
WARNING
This mark indicates procedures which, if improp-
erly performed, might lead to the death or serious
injury of the user.
CAUTION
This mark indicates procedures which, if improp-
erly performed, might possibly result in personal
harm to the user, or damage to property.
PRECAUTIONS ON USE
WARNING
●Do not keep exposing oneself to the direct airflow of air conditioner for a
long time.
●Do not insert fingers or objects into the outlet port or other openings.
●Except for EMERGENCY, never turn off the main or sub breaker of the
indoor units during operation. It will cause compressor failure or water
leakage. When stopping the operation, stop the indoor unit by operat-
ing the control unit, converter or external input device and then cut the
breaker. Make sure to operate through the control unit, converter, or
external input device.
●If the power supply cord of this product is damaged, it should only be
replaced by the authorized service personal, since special purpose tools
and specified cord are required.
●If any refrigerant happens to leak, extinguish any flames, ventilate the
room and get in touch with authorized service personnel.
CAUTION
●Do not place animals or plants in the direct path of the airflow.
●Do not direct airflow at fireplaces or heating apparatus.
●Do not block or cover the inlet port and outlet port.
●Do not climb on, or place objects on, the air conditioner.
●Do not set flower vases or water containers on top of air conditioners.
●Do not hang objects from the indoor unit.
●Do not place anything below the indoor unit that should not get wet.
●Always turn off the electrical breaker whenever cleaning the air condi-
tioner or the air filter.
●Do not pour water or cleaning solvent on the unit directly, or wash the unit
with them.
●Do not expose the air conditioner directly to water.
●Do not operate the air conditioner with wet hands.
●Check the condition of the installation stand for damage.
●Operate only with air filters installed.
●Do not drink the water drained from the air conditioner.
●Do not apply any heavy pressure to radiator fins.
●Do not use flammable gases near the air conditioner.
●Do not touch the pipes during the operation.
●Ensure that any electronic equipment is at least 40 in.(1 m) away from
either the indoor or outdoor units.
●This product is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the product by a person responsible for their safety.
Children should be supervised to ensure that they do not play with this
product.
NOTE:
Switching the operating mode in the heat recovery system may require
some time to prepare for operation. Please note that this is not a fault.
PRECAUTIONS ON INSTALLATION
CAUTION
●Do not attempt to install this air conditioner by yourself.
●This unit contains no user-serviceable parts. Always consult authorized
service personnel for repairs.
●When moving, consult authorized service personnel for removal or instal-
lation of the unit.
●The unit must be earthed (grounded).
●Make sure drain work is implemented properly for drainage.
●Avoid installing the air conditioner near a fireplace or other heating apparatus.
●When installing the indoor and outdoor units, take precautions to prevent
access by infants.
NAME OF PARTS
(1)
(2)
(1) Outlet port
(2) Intake port
Control unit (optional)
Types of remote controllers:
●Wireless remote controller
(*Be sure to use after connecting the optional IR receiver unit.)
●Wired remote controller
●Simple remote controller
For operation method, refer to the operating manual of each control unit.
Contents
SAFETY PRECAUTIONS....................................................................... 1
NAME OF PARTS .................................................................................. 1
MANUAL AUTO OPERATION ............................................................... 2
OPERATING TIPS ................................................................................. 2
CLEANING AND CARE.......................................................................... 3
TROUBLESHOOTING ........................................................................... 3
SPECIFICATIONS.................................................................................. 4
9380242000-01_OM_3L.indb 19380242000-01_OM_3L.indb 1 2021/4/22 13:39:012021/4/22 13:39:01

En-2
MANUAL AUTO OPERATION
Use the Manual auto operation in the event the remote controller is lost or
otherwise unavailable.
(*Limited to only when the optional IR receiver unit is connected.)
CAUTION
Do not press the MANUAL AUTO button with wet hands or pointed objects,
otherwise an electric shock or malfunction may occur.
Starting operation
Press the MANUAL AUTO button on the IR receiver unit.
The operation starts in the setting below.
Operating mode Auto:
When Auto mode cannot be selected, it will oper-
ate in the same mode as the other indoor unit in
the same system. (When no indoor unit is operat-
ing in the same system, the air conditioner will
operate in the Cooling mode.)
Fan speed Auto
Setting temperature 74°F (23 °C)
Stopping operation
Press the MANUAL AUTO button on the IR receiver unit.
Emergency heat
* It is available when this function is enabled. Please consult an authorized
service personnel as to whether this function is enabled.
Set emergency heat
During heating operation, press the MANUAL AUTO but-
ton on the IR receiver unit.
Auxiliary heater will be primary heater, and the outdoor unit will stop.
The Operation indicator lamp (green) blinks during the Emergency heat
operation.(3 seconds on, 1 second off.)
Cancel emergency heat
During the Emergency heat operation, press the MANU-
AL AUTO button on the IR receiver unit.
OPERATING TIPS
Operation and performance
About priority state and standby state
●Multiple indoor units can be connected within the same system. Depend-
ing on the system, choice of operating mode are limited.
Cooling priority state:
When the other indoor units within the same system operate in cooling or
dry mode, heating cannot be selected at the same time.
Heating priority state:
When the other indoor units within the same system operate in heating
mode, cooling and dry mode cannot be selected at the same time.
Standby state:
The standby state activates when 2 or more indoor units start up at the
same time in different mode. Any indoor unit other than priority mode will
wait in standby state until priority mode changes (operation starts as soon
as priority is switched).
At this time, the Operation indicator lamp (green) will turn on and the
Timer indicator lamp (orange) will blink. (Limited to only when the IR
receiver unit is connected)
Low ambient cooling
●When the outdoor temperature drops, the outdoor unit’s fans may switch
to Low Speed, or one of the fans may stop intermittently.
Heating performance
●Heating mode operates on the heat pump principle, absorbing heat from
outdoor air and transferring that heat indoors. As a result, the operating
performance is reduced as outdoor air temperature drops. If you feel that
insufficient heating performance is being produced, we recommend you
use this air conditioner in conjunction with another type of heating appli-
ance.
●Heating mode heat your entire room by recirculating air throughout the
room, with the result that some time may be required after first starting
the air conditioner until the room is heated.
Automatic defrosting
●When using the Heating mode under conditions of low outdoor air tem-
perature high humidity, frost may form on the outdoor unit, resulting in
reduced operating performance. In order to prevent this kind of reduced
performance, this unit is equipped with Automatic defrosting function. If
frost forms, the air conditioner will temporarily stop, and the defrosting
circuit will operate briefly (for about 4 to 15 minutes).
During the Automatic defrosting operation, the Operation indicator lamp
(green) will blink. (Limited to only when the IR receiver unit is connect-
ed.)
Oil recovery operation
●Periodically, the Oil recovery operation is performed in order to return
compressor oil to the outdoor unit.
During Oil recovery operation, the Operation indicator lamp (green) will
blink (for about 10 minutes). (Limited to only when the IR receiver unit is
connected.)
9380242000-01_OM_3L.indb 29380242000-01_OM_3L.indb 2 2021/4/22 13:39:012021/4/22 13:39:01

En-3
Temperature and humidity range
●The temperature and humidity required for operating this product is as
shown in the following table.
Cooling/Dry mode Heating mode
Outdoor
temperature Please refer to the specifications of outdoor units.
Indoor
temperature
About 64 to 90 °F DB
(18 to 32 °C DB)
About 50 to 86 °F DB
(10 to 30 °C DB)
Indoor humidity About 80% or less
●If the air conditioner is operated under higher temperature conditions than
those listed, the built-in protection circuit may operate to prevent internal
circuit damage. Also, during Cooling and Dry modes, if the unit is used
under conditions of lower temperature than those listed above, the heat-
exchanger may freeze, leading to water leakage and other damage.
●If the unit is used for long periods under high-humidity conditions, con-
densation may form on the surface of the indoor unit, and drip onto the
floor or other objects underneath.
●Do not use this unit for any purposes other than the Cooling, Heating,
Dehumidifying, and air-circulation of rooms in ordinary dwellings.
CLEANING AND CARE
CAUTION
●Before cleaning the unit, be sure to stop the unit and disconnect the
power supply.
●Do not stand on an unstable platform when cleaning.
●When removing and replacing the air filters, be sure not to touch the heat
exchanger, as personal injury may result.
●When used for extended periods, the indoor unit may accumulate dust
inside, reducing its performance. We recommend that the indoor unit be
inspected regularly, in addition to your own cleaning and care. For more
information, consult authorized service personnel.
●Do not clean the inside of the unit by yourself. To clean the inside, always
consult authorized service personnel.
●When cleaning the unit’s body, do not use water hotter than 104 °F (40
°C), harsh abrasive cleansers, or volatile agents like benzene or thinner.
●If dirt is allowed to accumulate on the air filter, airflow will be reduced,
lowering operating efficiency and increasing noise.
During periods of normal use, the air filters should be cleaned regularly.
If dirt is allowed to accumulate on the air filter, airflow will be reduced,
lowering operating efficiency and increasing noise.
When not using for an extended period
Leave the breaker on for at least 12 hours before starting operation when it
is to be used again.
TROUBLESHOOTING
The following conditions are not breakdowns or opera-
tion failures.
Doesn’t operate immediately:
●If the unit is stopped and then immediately started again, the compressor
will not operate for about 3 minutes, in order to prevent fuse blowouts.
●Whenever the electrical breaker is turned off then on again, the protection
circuit will operate for about 3 minutes, preventing unit operation during
that period.
Airflow is weak or stops:
●When Heating operation is started, indoor unit’s fan may temporarily stop,
to allow internal parts to warm up.
●During Heating operation, if the room temperature rises above the setting
of the remote controller, the outdoor unit will stop, and the indoor unit’s
fan will stop. If you wish to warm the room further, set a higher setting.
●During Oil recovery operation, the airflow may stop for approximately 10
minutes. (Refer to “OPERATING TIPS”)
●During Heating operation, the unit will temporarily stop operation (be-
tween 4 and 15 minutes) as the Automatic defrosting mode operates.
(Refer to “OPERATING TIPS”)
●The fan may operate at low speed during Dry operation or when the unit
is monitoring the room’s temperature.
●In the monitoring in the Auto mode, the fan will operate at low speed.
Indicator lamps are blinking:
(*Limited to only when the optional IR receiver unit is connected.)
●The Operation indicator lamp (green) flashes:
An oil recovery operation is being performed. (Refer to “OPERATING
TIPS”)
The Automatic defrosting operation is being performed. (Refer to “OPER-
ATING TIPS”)
●The Operation indicator lamp (green) and Timer indicator lamp (orange)
are blinking alternately:
It has recovered from a power outage.
●The Operation indicator lamp (green) and Timer indicator lamp (orange)
are blinking simultaneously:
It is operating in the test run mode. Ask a manager as there may be
maintenance being conducted.
●The Operation indicator lamp (green) is on and the TIMER indicator lamp
(orange) is blinking:
This is the standby state. (Refer to “OPERATING TIPS”)
Noise is heard:
●In the following conditions there are sounds of water flowing from the
indoor unit and the operation sound becomes loud. These are the refrig-
erant flow sound.
When operation starts
When oil recovery operation finishes
When Automatic defrosting operation finishes
●During operation, a slight squeaking sound may be heard. This is the
result of minute expansion and contraction of the panel due to tempera-
ture changes.
●During Heating operation, a sizzling sound may be heard occasionally.
This sound is produced by the Automatic defrosting operation. (Refer to
“OPERATING TIPS”)
Smells:
●Some smell may be emitted from the indoor unit. This smell is the result
of room smells (furniture, tobacco, etc.) which have been taken into the
air conditioner.
9380242000-01_OM_3L.indb 39380242000-01_OM_3L.indb 3 2021/4/22 13:39:012021/4/22 13:39:01

En-4
Fog comes out of the outdoor unit:
●During Cooling operation, a thin mist may be seen emitted from the
indoor unit. This results from the sudden Cooling of room air by the air
emitted from the air conditioner, resulting in condensation and misting.
Steam comes out of the indoor unit:
●During Heating operation, the outdoor unit’s fan may stop, and steam
may be seen rising from the unit. This is due to the Automatic defrosting
operation. (Refer to “OPERATING TIPS”)
Water is produced from the outdoor unit:
●During Heating operation, water may be produced from the outdoor unit
due to the Automatic defrosting operation.
The following conditions may not be breakdowns so
check again.
Doesn’t operate at all:
●Has there been a power failure?
●Has a fuse blown out, or a circuit breaker been tripped?
●Is the main power switch set to the OFF position?
●Are you trying to engage in an operation different from the priority state?
(Refer to “OPERATING TIPS”)
●Is it in standby state? (Refer to “OPERATING TIPS”)
The operation mode cannot be changed:
●Are you trying to change to an operation different from the priority condi-
tions? (Refer to “OPERATING TIPS”)
Poor Cooling (or Heating) performance:
●Did you adjust the temperature setting correctly?
●Is the air filter dirty? (Refer to “CLEANING AND CARE”)
●Are the air conditioner’s inlet port or outlet port blocked?
●Is there a window or door open?
●In the case of Cooling operation, is a window allowing bright sunlight to
enter? (Close the curtains.)
●In the case of Cooling operation, are there heating apparatus and com-
puters inside the room, or are there too many people in the room?
●Is the fan speed set to low?
Temperature does not fall down well.
●Temperature may not fall down depending on the room conditions. (While
high humidity or the room temperature is high.) (Refer to “OPERATING
TIPS”)
Set the temperature lower than the room temperature and use it.
In the following situations stop operation immediately
and get in touch with authorized service personnel.
●The problem cannot be solved even when the troubleshooting checks
have been performed.
●The Filter indicator lamp (red) is blinking very fast (when the IR receiver
unit is connected).
●The Wired remote controller or Simple remote controller indicate “Er”
(when either controller is connected).
●It has burning smell.
●For details on marking the blinking lamps, please refer to the Manual of
“IR receiver unit” or “Wired remote controller”.
SPECIFICATIONS
Model ARUX12
TLAV2
ARUX18
TLAV2
ARUX24
TLAV2
Power source 208/230 V ~ 60 Hz
Available voltage
range 187 to 253 V
Cooling
capacity
Btu/h
(kW)
12,000
(3.5)
18,000
(5.3)
24,000
(7.0)
Heating
capacity
Btu/h
(kW)
13,500
(4.0)
20,000
(5.9)
27,000
(7.9)
Dimensions and weight
Height in
(mm)
43.0
(1,092)
Width in
(mm)
17.5
(444)
Depth in
(mm)
21.0
(533)
Weight lbs
(kg)
100
(45)
102
(46)
Model ARUX30
TLAV2
ARUX36
TLAV2
ARUX48
TLAV2
ARUX60
TLAV2
Power source 208/230 V ~ 60 Hz
Available voltage
range 187 to 253 V
Cooling
capacity
Btu/h
(kW)
30,000
(8.8)
36,000
(10.6)
48,000
(14.1)
60,000
(17.6)
Heating
capacity
Btu/h
(kW)
34,000
(10.0)
40,000
(11.7)
54,000
(15.8)
67,000
(19.6)
Dimensions and weight
Height in
(mm)
48.0
(1,219)
58.75
(1,492)
Width in
(mm)
21.0
(533)
24.5
(622)
Depth in
(mm)
21.0
(533)
21.75
(552)
Weight lbs
(kg)
126
(57)
172
(78)
181
(82)
●Standard static pressure : 0.5 in WG (125 Pa)
9380242000-01_OM_3L.indb 49380242000-01_OM_3L.indb 4 2021/4/22 13:39:012021/4/22 13:39:01

9380242000-01_OM_3L.indb 19380242000-01_OM_3L.indb 1 2021/4/22 13:39:022021/4/22 13:39:02