Fujitsu Inverter halcyon asu24rlxq User manual

KEEP THIS OPERATION MANUAL

FOR FUTURE REFERENCE

FUJITSU GENERAL LIMITED P/N9315345165-01

OPERATING MANUAL

MODE D’EMPLOI

MANUAL DE FUNCIONAMIENTO

English

Français

Español

Indoor Unit

ASU24RLXQ

ASU30RLXQ

Outdoor Unit

AOU24RLXQ

AOU30RLXQ

HEAT&COOLING MODEL

(REVERSE CYCLE)

ROOM AIR CONDITIONER

WALL MOUNTED TYPE

En-1

ESPECIFICACIONES

ALIMENTACIÓN ........................................................................................................................................................................................................................................................ 208/230 V~60 Hz

REFRIGERACIÓN

CAPACIDAD ................................................................................................................................................................................................................................................................

24200 BTU/h

ENTRADA DE ALIMENTACIÓN ........................................................................................................................................................................................................................................

2,18

CORRIENTE .............................................................................................................................................................................................................................................................................9

6 A

CALEFACCIÓN

27600 BTU/h

38 kW

FICHE TECHNIQUE

ALIMENTATION ......................................................................................................................................................................................................................................................... 208/230 V~60 Hz

REFROIDISSEMENT

PUISSANCE FRIGORIFIQUE ......................................................................................................................................................................................................................................

24200 BTU/h

PUISSANCE ABSORBÉE ....................................................................................................................................................................................................................................................

2,18

INTENSITÉ ..............................................................................................................................................................................................................................................................................9

6 A

CHAUFFAGE

27600 BTU/h

2,38 kW

INTENSITE ............................................................................................................................................................................................................................................................................10

5 A

SPECIFICATIONS

POWER SUPPLY ........................................................................................................................................................................................................................................................ 208/230 V~60 Hz

COOLING

CAPACITY ...................................................................................................................................................................................................................................................................

24200 BTU/h

INPUT POWER ...................................................................................................................................................................................................................................................................

2.18 kW

CURRENT ............................................................................................................................................................................................................................................................................... 9.6 A

HEATING

27600 BTU/h

2.38 kW

MODEL INDOOR UNIT

MODÈLE UNIDAD INTERIOR

MODELO UNITÉ INTÉRIEURE

OUTDOOR UNIT

UNIDAD EXTERIOR

UNITÉ EXTÉRIEURE

ASU24RLXQ

AOU24RLXQ

TYPE HEAT & COOL MODEL

TYPE MODÈLE RÉVERSIBLE

TIPO MODELO DE REFRIGERACIÓN Y CAlEFACCÓN

CONTENTS

SAFETY PRECAUTIONS..................................... En-1

FEATURES AND FUNCTIONS............................ En-2

NAME OF PARTS ................................................ En-3

PREPARATION .................................................... En-4

OPERATION ........................................................ En-5

AIR CLEANING OPERATION .............................. En-7

TIMER OPERATION ............................................ En-8

SLEEP TIMER OPERATION ................................ En-9

MANUAL AUTO OPERATION ............................ En-9

ADJUSTING THE DIRECTION OF

AIR CIRCULATION ............................................ En-10

SWING OPERATION .......................................... En-11

COIL DRY OPERATION ...................................... En-11

CLEANING AND CARE ..................................... En-12

CLEANING THE PLASMA

AIR CLEANING FILTER ..................................... En-13

TROUBLESHOOTING ....................................... En-16

OPERATING TIPS ............................................. En-17

SAFETY PRECAUTIONS

●Do not attempt to install this air conditioner by yourself.

●This unit contains no user-serviceable parts. Always consult authorized service per-

sonnel for repairs.

●When moving, consult authorized service personnel for disconnection and installa-

tion of the unit.

●Do not become excessively chilled by staying for lengthy periods in the direct cooling

airflow.

●Do not insert fingers or objects into the outlet port or intake grilles.

●Do not start and stop air conditioner operation by disconnecting the power supply

cord and so on.

●Take care not to damage the power supply cord.

●In the event of a malfunction (burning smell, etc.), immediately stop operation, dis-

connect the power supply plug, and consult authorized service personnel.

●Provide occasional ventilation during use.

●Do not direct air flow at fireplaces or heating apparatus.

●Do not climb on, or place objects on, the air conditioner.

●Do not hang objects from the indoor unit.

●Do not set flower vases or water containers on top of air conditioners.

●Do not expose the air conditioner directly to water.

●Do not operate the air conditioner with wet hands.

●Do not pull power supply cord.

●Turn off power source when not using the unit for extended periods.

●Check the condition of the installation stand for damage.

●Do not place animals or plants in the direct path of the air flow.

●Do not drink the water drained from the air conditioner.

●Do not use in applications involving the storage of foods, plants or animals, precision

equipment, or art works.

●Connection valves become hot during Heating; handle with care.

●Do not apply any heavy pressure to radiator fins.

●Operate only with air filters installed.

●Do not block or cover the intake grille and outlet port.

●Ensure that any electronic equipment is at least one metre away from either the in-

door or outdoor units.

●Avoid installing the air conditioner near a fireplace or other heating apparatus.

●When installing the indoor and outdoor unit, take precautions to prevent access to

infants.

●Do not use inflammable gases near the air conditioner.

●When restarting after a long period of disuse in the winter, turn the power switch on

at least 12 hours before starting the unit.

DANGER!

CAUTION!

OPERATION

TIMER

AIR CLEAN

Ջࣱݻବ

MANUAL

AUTO

Fig. 5

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 7

To facilitate explanation, the accompanying illustra-

tion has been drawn to show all possible indicators;

in actral operation, however, the display will only

show those indicators appropriate to the current op-

eration.

Fig. 6

[

e _

WIRED REMOTE CONTROL UNIT (OPTION)

The optional wired remote control unit (model No.: UTB-UUB) can be used.

When you use wired remote control unit, there are following different points as compared

with using wireless remote control unit.

[The additional functions for wired ones]

• Weekly timer

• Temperature set back timer

[The restricted functions for wired ones]

• QUIET can't be selected in FAN MODE.

• Sleep-timer can't be used.

• Coil dry can’t be used.

And you can't use both wired remote control unit and wireless simultaneously.

(Only one kind can be selected)

ESPECIFICACIONES

REFRIGERACIÓN

30600 BTU/h

3,86

0 A

CALEFACCIÓN

32000 BTU/h

00 kW

FICHE TECHNIQUE

REFROIDISSEMENT

30600 BTU/h

3,86

0 A

CHAUFFAGE

32000 BTU/h

3,00 kW

2 A

SPECIFICATIONS

COOLING

30600 BTU/h

3.86 kW

HEATING

32000 BTU/h

3.00 kW

MODEL INDOOR UNIT

MODÈLE UNIDAD INTERIOR

MODELO UNITÉ INTÉRIEURE

OUTDOOR UNIT

UNIDAD EXTERIOR

UNITÉ EXTÉRIEURE

ASU30RLXQ

AOU30RLXQ

TYPE HEAT & COOL MODEL

TYPE MODÈLE RÉVERSIBLE

TIPO MODELO DE REFRIGERACIÓN Y CAlEFACCÓN

En-1

ESPECIFICACIONES

REFRIGERACIÓN

24200 BTU/h

2,18

6 A

CALEFACCIÓN

27600 BTU/h

38 kW

FICHE TECHNIQUE

REFROIDISSEMENT

24200 BTU/h

2,18

6 A

CHAUFFAGE

27600 BTU/h

2,38 kW

5 A

SPECIFICATIONS

COOLING

24200 BTU/h

2.18 kW

HEATING

27600 BTU/h

2.38 kW

MODEL INDOOR UNIT

MODÈLE UNIDAD INTERIOR

MODELO UNITÉ INTÉRIEURE

OUTDOOR UNIT

UNIDAD EXTERIOR

UNITÉ EXTÉRIEURE

ASU24RLXQ

AOU24RLXQ

TYPE HEAT & COOL MODEL

TYPE MODÈLE RÉVERSIBLE

TIPO MODELO DE REFRIGERACIÓN Y CAlEFACCÓN

CONTENTS

SAFETY PRECAUTIONS..................................... En-1

FEATURES AND FUNCTIONS............................ En-2

NAME OF PARTS ................................................ En-3

PREPARATION .................................................... En-4

OPERATION ........................................................ En-5

AIR CLEANING OPERATION .............................. En-7

TIMER OPERATION ............................................ En-8

SLEEP TIMER OPERATION ................................ En-9

MANUAL AUTO OPERATION ............................ En-9

ADJUSTING THE DIRECTION OF

AIR CIRCULATION ............................................ En-10

SWING OPERATION .......................................... En-11

COIL DRY OPERATION ...................................... En-11

CLEANING AND CARE ..................................... En-12

CLEANING THE PLASMA

AIR CLEANING FILTER ..................................... En-13

TROUBLESHOOTING ....................................... En-16

OPERATING TIPS ............................................. En-17

SAFETY PRECAUTIONS

●Do not attempt to install this air conditioner by yourself.

●This unit contains no user-serviceable parts. Always consult authorized service per-

sonnel for repairs.

●When moving, consult authorized service personnel for disconnection and installa-

tion of the unit.

●Do not become excessively chilled by staying for lengthy periods in the direct cooling

airflow.

●Do not insert fingers or objects into the outlet port or intake grilles.

●Do not start and stop air conditioner operation by disconnecting the power supply

cord and so on.

●Take care not to damage the power supply cord.

●In the event of a malfunction (burning smell, etc.), immediately stop operation, dis-

connect the power supply plug, and consult authorized service personnel.

●Provide occasional ventilation during use.

●Do not direct air flow at fireplaces or heating apparatus.

●Do not climb on, or place objects on, the air conditioner.

●Do not hang objects from the indoor unit.

●Do not set flower vases or water containers on top of air conditioners.

●Do not expose the air conditioner directly to water.

●Do not operate the air conditioner with wet hands.

●Do not pull power supply cord.

●Turn off power source when not using the unit for extended periods.

●Check the condition of the installation stand for damage.

●Do not place animals or plants in the direct path of the air flow.

●Do not drink the water drained from the air conditioner.

●Do not use in applications involving the storage of foods, plants or animals, precision

equipment, or art works.

●Connection valves become hot during Heating; handle with care.

●Do not apply any heavy pressure to radiator fins.

●Operate only with air filters installed.

●Do not block or cover the intake grille and outlet port.

●Ensure that any electronic equipment is at least one metre away from either the in-

door or outdoor units.

●Avoid installing the air conditioner near a fireplace or other heating apparatus.

●When installing the indoor and outdoor unit, take precautions to prevent access to

infants.

●Do not use inflammable gases near the air conditioner.

●When restarting after a long period of disuse in the winter, turn the power switch on

at least 12 hours before starting the unit.

DANGER!

CAUTION!

OPERATION

TIMER

AIR CLEAN

Ջࣱݻବ

MANUAL

AUTO

Fig. 5

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 7

To facilitate explanation, the accompanying illustra-

tion has been drawn to show all possible indicators;

in actral operation, however, the display will only

show those indicators appropriate to the current op-

eration.

Fig. 6

[

e _

WIRED REMOTE CONTROL UNIT (OPTION)

The optional wired remote control unit (model No.: UTB-UUB) can be used.

When you use wired remote control unit, there are following different points as compared

with using wireless remote control unit.

[The additional functions for wired ones]

• Weekly timer

• Temperature set back timer

[The restricted functions for wired ones]

• QUIET can't be selected in FAN MODE.

• Sleep-timer can't be used.

• Coil dry can’t be used.

And you can't use both wired remote control unit and wireless simultaneously.

(Only one kind can be selected)

ESPECIFICACIONES

REFRIGERACIÓN

30600 BTU/h

3,86

0 A

CALEFACCIÓN

32000 BTU/h

00 kW

FICHE TECHNIQUE

REFROIDISSEMENT

30600 BTU/h

3,86

0 A

CHAUFFAGE

32000 BTU/h

3,00 kW

2 A

SPECIFICATIONS

COOLING

30600 BTU/h

3.86 kW

HEATING

32000 BTU/h

3.00 kW

MODEL INDOOR UNIT

MODÈLE UNIDAD INTERIOR

MODELO UNITÉ INTÉRIEURE

OUTDOOR UNIT

UNIDAD EXTERIOR

UNITÉ EXTÉRIEURE

ASU30RLXQ

AOU30RLXQ

TYPE HEAT & COOL MODEL

TYPE MODÈLE RÉVERSIBLE

TIPO MODELO DE REFRIGERACIÓN Y CAlEFACCÓN

En-1

ESPECIFICACIONES

REFRIGERACIÓN

24200 BTU/h

2,18

6 A

CALEFACCIÓN

27600 BTU/h

38 kW

FICHE TECHNIQUE

REFROIDISSEMENT

24200 BTU/h

2,18

6 A

CHAUFFAGE

27600 BTU/h

2,38 kW

5 A

SPECIFICATIONS

COOLING

24200 BTU/h

2.18 kW

HEATING

27600 BTU/h

2.38 kW

MODEL INDOOR UNIT

MODÈLE UNIDAD INTERIOR

MODELO UNITÉ INTÉRIEURE

OUTDOOR UNIT

UNIDAD EXTERIOR

UNITÉ EXTÉRIEURE

ASU24RLXQ

AOU24RLXQ

TYPE HEAT & COOL MODEL

TYPE MODÈLE RÉVERSIBLE

TIPO MODELO DE REFRIGERACIÓN Y CAlEFACCÓN

CONTENTS

SAFETY PRECAUTIONS..................................... En-1

FEATURES AND FUNCTIONS............................ En-2

NAME OF PARTS ................................................ En-3

PREPARATION .................................................... En-4

OPERATION ........................................................ En-5

AIR CLEANING OPERATION .............................. En-7

TIMER OPERATION ............................................ En-8

SLEEP TIMER OPERATION ................................ En-9

MANUAL AUTO OPERATION ............................ En-9

ADJUSTING THE DIRECTION OF

AIR CIRCULATION ............................................ En-10

SWING OPERATION .......................................... En-11

COIL DRY OPERATION ...................................... En-11

CLEANING AND CARE ..................................... En-12

CLEANING THE PLASMA

AIR CLEANING FILTER ..................................... En-13

TROUBLESHOOTING ....................................... En-16

OPERATING TIPS ............................................. En-17

SAFETY PRECAUTIONS

●Do not attempt to install this air conditioner by yourself.

●This unit contains no user-serviceable parts. Always consult authorized service per-

sonnel for repairs.

●When moving, consult authorized service personnel for disconnection and installa-

tion of the unit.

●Do not become excessively chilled by staying for lengthy periods in the direct cooling

airflow.

●Do not insert fingers or objects into the outlet port or intake grilles.

●Do not start and stop air conditioner operation by disconnecting the power supply

cord and so on.

●Take care not to damage the power supply cord.

●In the event of a malfunction (burning smell, etc.), immediately stop operation, dis-

connect the power supply plug, and consult authorized service personnel.

●Provide occasional ventilation during use.

●Do not direct air flow at fireplaces or heating apparatus.

●Do not climb on, or place objects on, the air conditioner.

●Do not hang objects from the indoor unit.

●Do not set flower vases or water containers on top of air conditioners.

●Do not expose the air conditioner directly to water.

●Do not operate the air conditioner with wet hands.

●Do not pull power supply cord.

●Turn off power source when not using the unit for extended periods.

●Check the condition of the installation stand for damage.

●Do not place animals or plants in the direct path of the air flow.

●Do not drink the water drained from the air conditioner.

●Do not use in applications involving the storage of foods, plants or animals, precision

equipment, or art works.

●Connection valves become hot during Heating; handle with care.

●Do not apply any heavy pressure to radiator fins.

●Operate only with air filters installed.

●Do not block or cover the intake grille and outlet port.

●Ensure that any electronic equipment is at least one metre away from either the in-

door or outdoor units.

●Avoid installing the air conditioner near a fireplace or other heating apparatus.

●When installing the indoor and outdoor unit, take precautions to prevent access to

infants.

●Do not use inflammable gases near the air conditioner.

●When restarting after a long period of disuse in the winter, turn the power switch on

at least 12 hours before starting the unit.

DANGER!

CAUTION!

OPERATION

TIMER

AIR CLEAN

Ջࣱݻବ

MANUAL

AUTO

Fig. 5

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 7

To facilitate explanation, the accompanying illustra-

tion has been drawn to show all possible indicators;

in actral operation, however, the display will only

show those indicators appropriate to the current op-

eration.

Fig. 6

[

e _

WIRED REMOTE CONTROL UNIT (OPTION)

The optional wired remote control unit (model No.: UTB-UUB) can be used.

When you use wired remote control unit, there are following different points as compared

with using wireless remote control unit.

[The additional functions for wired ones]

• Weekly timer

• Temperature set back timer

[The restricted functions for wired ones]

• QUIET can't be selected in FAN MODE.

• Sleep-timer can't be used.

• Coil dry can’t be used.

And you can't use both wired remote control unit and wireless simultaneously.

(Only one kind can be selected)

ESPECIFICACIONES

REFRIGERACIÓN

30600 BTU/h

3,86

0 A

CALEFACCIÓN

32000 BTU/h

00 kW

FICHE TECHNIQUE

REFROIDISSEMENT

30600 BTU/h

3,86

0 A

CHAUFFAGE

32000 BTU/h

3,00 kW

2 A

SPECIFICATIONS

COOLING

30600 BTU/h

3.86 kW

HEATING

32000 BTU/h

3.00 kW

MODEL INDOOR UNIT

MODÈLE UNIDAD INTERIOR

MODELO UNITÉ INTÉRIEURE

OUTDOOR UNIT

UNIDAD EXTERIOR

UNITÉ EXTÉRIEURE

ASU30RLXQ

AOU30RLXQ

TYPE HEAT & COOL MODEL

TYPE MODÈLE RÉVERSIBLE

TIPO MODELO DE REFRIGERACIÓN Y CAlEFACCÓN

En-2

FEATURES AND FUNCTIONS

INVERTER

At the start of operation, a large power is used to bring the

room quickly to the desired temperature. Afterwards, the

unit automatically switches to a low power setting for eco-

nomic and comfortable operation.

COIL DRY OPERATION

The Indoor unit can be dried by pressing the COIL DRY but-

ton on the Remote Control Unit so as to avoid going moldy

and restrain the breed of bacterium.

AUTO CHANGEOVER

The operation mode (cooling, dry, heating) is switched au-

tomatically to maintain the set temperature, and the tem-

perature is kept constant at all times.

PROGRAM TIMER

The program timer allows you to integrate OFF timer and

ON timer operations in a single sequence. The sequence

can involve one transition from OFF timer to ON timer, or

from ON timer to OFF timer, within a twenty-four hour pe-

riod.

SLEEP TIMER

When the SLEEP button is pressed during Heating mode,

the air conditioner’s thermostat setting is gradually lowered

during the period of operation; during cooling mode, the

thermostat setting is gradually raised during the period of

operation. When the set time is reached, the unit automati-

cally turns off.

WIRELESS REMOTE CONTROL UNIT

The Wireless Remote Control Unit allows convenient con-

trol of air conditioner operation.

HORIZONTAL AIRFLOW: COOLING/

DOWNWARD AIRFLOW: HEATING

For cooling, use horizontal airflow so the cool air does not

blow directly on the occupants in the room. For heating,

use downward airflow to send powerful, warm air to the

floor and create a comfortable environment.

OMNI-DIRECTIONAL AIR FLOW

(SWING OPERATION)

Three-dimensional control over air direction swing is possi-

ble through dual use of both an UP/DOWN air direction swing

and RIGHT/LEFT air direction swing. Since UP/DOWN air

direction flaps operate automatically according to the oper-

ating mode of the unit, it is possible to set air direction based

on the operating mode.

REMOVABLE OPEN PANEL

The indoor unit’s Open Panel can be removed for easy clean-

ing and maintenance.

MILDEW-RESISTANT FILTER

The AIR FILTER has been treated to resist mildew growth,

thus allowing cleaner use and easier care.

SUPER QUIET OPERATION

When the FAN CONTROL button is used to select QUIET,

the unit begins super-quiet operation; the indoor unit’s air-

flow is reduced to produce quieter operation.

AIR CLEANING MODE

Relies on the air conditioner’s power to quickly purify the air

in the room.

ELECTRONIC AIR CLEAN FILTER

Install for use inside of the dust collection unit. For details

on how to install the filter, please refer to page 15.

Electrical power is used to charge the filter to remove con-

taminants from the air and to effectively collect dust and

remove odors. It also helps to reduce the bacterial activity.

En-3

Fig. 6 Remote Control Unit

JSLEEP button

KMASTER CONTROL button

LAIR CLEAN button

MSET TEMP. button ( / )

NCOIL DRY button

OSignal Transmitter

PTIMER MODE button

QTIMER SET ( / ) button

RFAN CONTROL button

SSTART/STOP button

TSET button (Vertical)

USET button (Horizontal)

VSWING button

WRESET button

XTEST RUN button

●This button is used when installing the

conditioner, and should not be used un-

der normal conditions, as it will cause the

air conditioner’s thermostat function to op-

erate incorrectly.

●If this button is pressed during normal op-

eration, the unit will switch to test opera-

tion mode, and the Indoor Unit’s OPERA-

TION Indicator Lamp and TIMER Indicator

Lamp will begin to flash simultaneously.

●To stop the test operation mode, press the

START/STOP button to stop the air condi-

tioner.

YCLOCK ADJUST button

ZRemote Control Unit Display (Fig. 7)

[Transmit Indicator

\Clock Display

]Operating Mode Display

_Timer Mode Display

aFan Speed Display

bTemperature SET Display

cAIR CLEAN Display

dCOIL DRY Display

eSLEEP Display

fSWING Display

NAME OF PARTS

●Refer to the folded out page on the cover.

Fig. 1 Indoor Unit

1Operating Control Panel (Fig. 2)

2MANUAL AUTO button

●When kept on pressing the MANUAL

AUTO button for more than 10 seconds,

the forced cooling operation will start.

●The forced cooling operation is used at the

time of installation.

Only for authorized service personnel's

use.

●When the forced cooling operation starts

by any chance, press the START/STOP but-

ton to stop the operation.

3Indicator (Fig. 3)

4Remote Control Signal Receiver

OPERATION Indicator Lamp (red)

6TIMER Indicator Lamp (green)

●If the TIMER indicator lamp flashes when

the timer is operating, it indicates that a

fault has occurred with the timer setting

(See Page 14 Auto Restart).

7AIR CLEAN Indicator Lamp (orange)

8Intake Grille (Fig. 4)

9Front Panel

0Air Filter

AAir Flow Direction Louver

BPower Diffuser

CRight-Left Louver

(behind Air Flow Direction Louver)

DDrain Hose

EElectrical Air Cleaning Filter

Fig. 5 Outdoor Unit

FIntake Port

GOutlet Port

HPipe Unit

IDrain port (bottom)

En-4

PREPARATION

CAUTION!

●Take care to prevent infants from

accidentally swallowing batteries.

●When not using the Remote Control Unit

for an extended period, remove the

batteries to avoid possible leakage and

damage to the unit.

●If leaking battery fluid comes in contact

with your skin, eyes, or mouth, immedi-

ately wash with copious amounts of

water, and consult your physician.

●Dead batteries should be removed

immediately and disposed of properly,

either in a battery collection receptacle

or to the appropriate authority.

●Do not attempt to recharge dry batteries.

Never mix new and used batteries, or

batteries of different types.

Batteries should last about one year

under normal use. If the Remote Con-

trol Unit’s operating range becomes ap-

preciably reduced, replace the batteries

and press the RESET button with the tip

of a ballpoint pen or other small object.

Load Batteries (AAA/R03/LR03 ××

××

×2)

1Press and slide the battery compartment lid on the re-

verse side to open it.

Slide in the direction of the arrow while pressing the mark.

2Insert batteries.

Be sure to align the battery polarities ( ) correctly.

3Close the battery compartment lid.

Set the Current time

1Press the CLOCK ADJUST button (Fig. 6 Y).

Use the tip of a ball-point pen or other small object to press the button.

2Use the TIMER SET ( / ) buttons (Fig. 6 Q) to

adjust the clock to the current time.

button: Press to advance the time.

button: Press to reverse the time.

(Each time the buttons are pressed, the time will be advanced/reversed in

one-minute increments; hold the buttons depressed to change the time

quickly in ten-minute increments.)

3Press the CLOCK ADJUST button (Fig. 6 Y) again.

This completes the time setting and starts the clock.

To Use the Remote Control Unit

●The Remote Control Unit must be pointed at signal receiver (Fig. 1 4) to operate

correctly.

●Operating Range: About 7 meters.

●When a signal is properly received by the air conditioner, a beeping sound will

be heard.

●If no beep is heard, press the Remote Control Unit button again.

Remote Control Unit Holder

3To remove the Remote

Control Unit (when use at

hand).

1Mount the Holder. 2Set the Remote Control

Unit.

Screws

Insert

Press in

Slide up

Pull out

En-5

To Select Mode Operation

1Press the START/STOP button (Fig.6 S).

The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 ) will light.

The air conditioner will start operating.

2Press the MASTER CONTROL button (Fig.6 K) to se-

lect the desired mode.

Each time the button is pressed, the mode will change in the following

order.

AUTO COOL DRY

HEAT FAN

About three seconds later, the entire display will reappear.

To Set the Thermostat

Press the SET TEMP. button (Fig. 6 M).

button: Press to raise the thermostat setting.

button: Press to lower the thermostat setting.

●Thermostat setting range:

AUTO .................................. 64-88 °F

Heating ............................... 60-88 °F

Cooling/Dry ........................ 64-88 °F

The thermostat cannot be used to set room temperature during the FAN mode (the

temperature will not appear on the Remote Control Unit’s Display).

About three seconds later, the entire display will reappear.

The thermostat setting should be considered a standard value, and may differ

somewhat from the actual room temperature.

To Set the Fan Speed

Press the FAN CONTROL button (Fig. 6 R).

Each time the button is pressed, the fan speed changes in the following order:

AUTO HIGH MED LOW QUIET

About three seconds later, the entire display will reappear.

When set to AUTO:

Heating : Fan operates so as to optimally circulate warmed air.

However, the fan will operate at very low speed when the temperature

of the air issued from the indoor unit is low.

Cooling : As the room temperature approaches that of the thermostat setting,

the fan speed becomes slower.

Fan : The fan runs at the low fan speed.

The fan will operate at a very low setting during Monitor operation and at the

start of the Heating mode.

SUPER QUIET Operation

When set to Quiet:

SUPER QUIET operation begins.The indoor unit’s airflow will be reduced for qui-

eter operation.

●SUPER QUIET operation cannot be used during Dry mode. (The same is true

when dry mode is selected during AUTO mode operation.)

●During Super Quiet operation, Heating and Cooling performance will be reduced

somewhat. If the room does not warm up/ cool down when using SUPER QUIET

Operation, please adjust the air conditioner’s Fan Speed.

OPERATION

ssss

Example: When set to COOL.

Example: When set to 80°F.

Example: When set to AUTO.

sss

En-6

To Stop Operation

Press the START/STOP button (Fig. 6 S).

The OPERATION Indicator Lamp (red) (Fig. 3 ) will go out.

About AUTO CHANGEOVER Operation

AUTO: ●When AUTO CHANGEOVER operation first selected, the fan will oper-

ate at very low speed for about one minute, during which time the unit

detects the room conditions and selects the proper operating mode.

If the differance between thermostat setting and actual room tempera-

ture is more than +4 °F →Cooling or dry operation

If the difference between thermostat setting and actual room tempera-

ture is within ±4 °F →Monitor operation

If the difference between thermostat setting and actual room tempera-

ture is more than –4 °F →Heating operation

●When the air conditioner has adjusted your room’s temperature to near

the thermostat setting, it will begin monitor operation. In the monitor

operation mode, the fan will operate at low speed. If the room tem-

perature subsequently changes, the air conditioner will once again

select the appropriate operation (Heating, Cooling) to adjust the tem-

perature to the value set in the thermostat.

(The monitor operation range is ±4 °F relative to the thermostat set-

ting.)

●If the mode automatically selected by the unit is not what you wish,

select one of the mode operation (HEAT, COOL, DRY, FAN).

About Mode Operation

Heating: ●Use to warm your room.

●When Heating mode is selected, the air conditioner will operate at very

low fan speed for about 3 to 5 minutes, after which it will switch to the

selected fan setting. This period of time is provided to allow the indoor

unit to warm up before begin full operation.

●When the room temperature is very low, frost may form on the outside

unit, and its performance may be reduced. In order to remove such

frost, the unit will automatically enter the defrost cycle from time to

time. During Automatic Defrosting operation, the OPERATION Indica-

tor Lamp (Fig. 3 ) will flash, and the heat operation will be inter-

rupted.

●After the start of heating operation, it takes some time before the room

gets warmer.

Cooling: ●Use to cool your room.

Dry: ●Use for gently cooling while dehumidifying your room.

●You cannot heat the room during Dry mode.

●During Dry mode, the unit will operate at low speed; in order to adjust

room humidity, the indoor unit’s fan may stop from time to time. Also,

the fan may operate at very low speed when adjusting room humidity.

●The fan speed cannot be changed manually when Dry mode has been

selected.

Fan: ●Use to circulate the air throughout your room.

During Heating mode:

Set the thermostat to a temperature set-

ting that is higher than the current room

temperature. The Heating mode will not

operate if the thermostat is set lower than

the actual room temperature.

During Cooling/Dry mode:

Set the thermostat to a temperature set-

ting that is lower than the current room

temperature. The Cooling and Dry modes

will not operate if the thermostat is set

higher than the actual room temperature

(in Cooling mode, the fan alone will oper-

ate).

During Fan mode:

You can not use the unit to heat and cool

your room.

En-7

2Press the AIR CLEAN button (Fig. 6 L).

The AIR CLEAN Indicator Lamp (green) (Fig. 3 7) will light up.

● Air conditioning and Air Cleaning will function simultaneously.

Air cleaning

●During operation, the unit produces a small amount of ozone that can be smelled.

●When this unit is used in combination with the ultrasonic humidifier, white parti-

cles may become attached to the plasma filter unit. If this happens, clean the

plasma filter unit as soon as possible. (Refer to page 13, 14.)

●The air cleaning operation cannot remove gases such as carbon monoxide and

alcohol from the air. During operation, ventilate the room often to prevent as-

phyxiation or suffocation.

●If the intake filter is removed during operation, a safety device will stop the op-

eration of the plasma filter unit. If this happens, the AIR CLEAN Indicator Lamp

(orange) on the indoor unit will flash after some time has passed. Use the START/

STOP button on the remote controller to stop the operation, install the intake

filter, and then use the START/STOP button to restart the operation.

●Use the FAN CONTROL button to change the fan speed. (Refer to page 5.) The

plasma filter unit operates most effectively at the highest fan speed.

●The AIR CLEAN Indicator Lamp (orange) will flash to inform you that the periodic

cleaning of the plasma filter unit is required. (Refer to page 13, 14.)

AIR CLEANING OPERATION

If you wish to stop Air Clean

Press the AIR CLEAN button (Fig. 6 L) once again.

The AIR CLEAN Indicator Lamp (orange) (Fig. 3 7) will go out.

●This will only stop the Air Cleaning, the air conditioner will continue operating.

To also stop the air conditioner

Press the START/STOP button (Fig. 6 S).

The OPERATION Indicator Lamp (red)

(Fig. 3 )

will go out.

●The next time the START / STOP button (Fig. 6 S) is pressed air conditioning

and air cleaning will both resume operating.

If you wish to eliminate dirt,dust,cigarette smoke, pollen, or just simply purify the

air of the room, use the Air Cleaning Mode.

1Press the START/STOP button (Fig. 6 S).

The OPERATION Indicator Lamp (red) (Fig. 3 ) will light.

(If the unit is already in operation, please proceed to step 2.)

En-8

TIMER OPERATION

Before using the timer function, be sure that the Remote Control Unit is set to the correct current time (☞P. 4).

To Use the ON timer or OFF timer

1Press the START/STOP button (Fig. 6 S)

(if the unit is already operating, proceed to step 2).

The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 ) will light.

2Press the TIMER MODE button (Fig. 6 P) to select the

OFF timer or ON timer operation.

Each time the button is pressed the timer function changes in the follow-

ing order:

CANCEL OFF ON

PROGRAM(OFF →ON, OFF ←ON)

The indoor unit’s greenTIMER Indicator Lamp (Fig. 3 6) will light.

3Use the TIMER SET buttons (Fig. 6 Q) to adjust the

desired OFF time or ON time.

Set the time while the time display is flashing (the flashing will continue

for about five seconds).

button: Press to advance the time.

button: Press to reverse the time.

About five seconds later, the entire display will reappear.

To Use the Program timer

1Press the START/STOP button (Fig. 6 S).

(if the unit is already operating, proceed to step 2).

The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 ) will light.

2Set the desired times for OFF timer and ON timer.

See the section “To Use the ON timer or OFF timer” to set the desired

mode and times.

About three seconds later, the entire display will reappear.

The indoor unit’sTIMER Indicator Lamp (green) (Fig. 3 6) will light.

3Press the TIMER MODE button (Fig. 6 P) to select the

PROGRAM timer operation (OFF ON or OFF ON

will display).

The display will alternately show “OFF timer” and “ON timer”, then change

to show the time setting for the operation to occur first.

●The program timer will begin operation. (If the ON timer has been se-

lected to operate first, the unit will stop operating at this point.)

About five seconds later, the entire display will reappear.

About the Program timer

●The program timer allows you to integrate OFF timer and ON timer operations in

a single sequence. The sequence can involve one transition from OFF timer to

ON timer, or from ON timer to OFF timer, within a twenty-four hour period.

●The first timer function to operate will be the one set nearest to the current time.

The order of operation is indicated by the arrow in the Remote Control Unit’s

Display (OFF →ON, or OFF ←ON).

●One example of Program timer use might be to have the air conditioner auto-

matically stop (OFF timer) after you go to sleep, then start (ON timer) automati-

cally in the morning before you arise.

To Cancel the Timer

Use the TIMER button to select “CANCEL”.

The air conditioner will return to normal

operation.

To Change the Timer Settings

Perform steps 2and 3.

To Stop Air Conditioner Operation

while the Timer is Operating

Press the START/STOP button.

To Change Operating Conditions

If you wish to change operating conditions

(Mode, Fan Speed, Thermostat Setting,

SUPER QUIET mode), after making the

timer setting wait until the entire display

reappears, then press the appropriate

buttons to change the operating condition

desired.

To Cancel the Timer

Use the TIMER MODE button to select

“CANCEL”.

The air conditioner will return to normal

operation.

To Change the Timer Settings

Follow the instructions given in the section

“To Use the ONTimer or OFFTimer” to se-

lect the timer setting you wish to change.

2. Press the TIMER MODE button to select

either OFF ON or OFF ON.

To Stop Air Conditioner Operation

while the Timer is Operating

Press the START/STOP button.

To Change Operating Conditions

If you wish to change operating conditions

(Mode, Fan Speed, Thermostat Setting,

SUPER QUIET mode), after making the timer

setting wait until the entire display reap-

pears, then press the appropriate buttons to

change the operating condition desired.

En-9

SLEEP TIMER OPERATION

Unlike other timer functions, the SLEEP timer is used to set the length of time until air conditioner operate is stopped.

To Use the SLEEP Timer

While the air conditioner is operating or stopped, press the

SLEEP button (Fig. 6 J).

The indoor unit’s OPERATION Indicator Lamp (red) (Fig. 3 ) lights and theTIMER

Indicator Lamp (green) (Fig. 3 6) light.

To Change the Timer Settings

Press the SLEEP button (Fig. 6 J) once again and set the time

using the TIMER SET ( / ) buttons (Fig. 6 Q).

Set the time while the Timer Mode Display is flashing (the flashing will continue

about five seconds).

button: Press to advance the time.

button: Press to reverse the time.

About five seconds later, the entire display will reappear.

To Cancel the Timer:

Use the TIMER MODE button to select

“CANCEL”.

The air conditioner will return to normal

operation.

To Stop the Air Conditioner During

Timer Operation:

Press the START/STOP button.

About the SLEEP Timer

To prevent excessive warming or cooling during sleep, the SLEEP timer function automatically modifies the thermostat setting

in accordance with the set time setting. When the set time has elapsed, the air conditioner completely stops.

During Cooling/Dry operation:

When the SLEEP timer is set, the thermostat setting is auto-

matically raised 2 °F every sixty minutes. When the thermo-

stat has been raised a total of 4 °F, the thermostat setting at

that time is maintained until the set time has elapsed, at which

time the air conditioner automatically turns off.

SLEEP timer setting

During Heating operation:

When the SLEEP timer is set, the thermostat setting is

automatically lowered 2 °F every thirty minutes. When the

thermostat has been lowered a total of 8 °F, the thermostat

setting at that time is maintained until the set time has elapsed,

at which time the air conditioner automatically turns off.

SLEEP timer setting

4 °F 6 °F 8 °F

minutes

2 °F

1 hour

30 minutes

Set time

1 hour

2 °F 4 °F

MANUAL AUTO OPERATION

Use the MANUAL AUTO operation in the event the Remote Control Unit is lost or otherwise unavailable.

How To Use the Main Unit Controls

Press the MANUAL AUTO button (Fig. 2 2) on the main unit

control panel.

To stop operation, press the MANUAL AUTO button (Fig. 2 2) once again.

(Controls are located inside the Open Panel)

●When the air conditioner is operated

with the controls on the Main Unit, it

will operate under the same mode as

the AUTO mode selected on the Re-

mote Control Unit (see page 6).

●The fan speed selected will be “AUTO”

and the thermostat setting will be

standard.(76°F)

En-10

ADJUSTING THE DIRECTION OF AIR CIRCULATION

●Adjust the up, down, left, and right AIR directions with the AIR DIRECTION buttons on the Remote Control Unit.

●Use the AIR DIRECTION buttons after the Indoor Unit has started operating and the airflow-direction louvers have

stopped moving.

RDANGER!

●Never place fingers or foreign objects in-

side the outlet ports, since the internal fan

operates at high speed and could cause

personal injury.

●Always use the Remote Control Unit’s

SET button to adjust the vertical airflow

louvers. Attempting to move them

manually could result in improper op-

eration; in this case, stop operation and

restart. The louvers should begin to

operate properly again.

●During use of the Cooling and Dry

modes, do not set the Air Flow Direc-

tion Louvers in the Heating range (4-

6) for long periods of time, since wa-

ter vapor may condense near the out-

let louvers and drops of water may drip

from the air conditioner. During the

Cooling and Dry modes, if the Air Flow

Direction Louvers are left in the heat-

ing range for more than 30 minutes,

they will automatically return to posi-

tion 3.

●When used in a room with infants, chil-

dren, elderly or sick persons, the air

direction and room temperature

should be considered carefully when

making settings.

Vertical Air Direction Adjustment

Press the SET button (Vertical) (Fig. 6 T).

Each time the button is pressed, the air direction range will change as follows:

12346

Types of Air flow Direction Setting:

1,2,3: During Cooling/Dry modes

4,,6: During Heating mode

The Remote Control Unit’s display does

not change.

●Use the air direction adjustments within the ranges shown above.

●The vertical airflow direction is set automatically as shown, in accordance with

the type of operation selected.

During Cooling/Dry mode : Horizontal flow 1

During Heating mode : Downward flow

●During AUTO mode operation, for the first minute after beginning operation,

airflow will be horizontal 1; the air direction cannot be adjusted during this pe-

riod.

●Direction 1 2

Only the direction of the Air Flow Direction Louver changes; the direction of the

Power Diffuser does not change.

Horizontal Air Direction Adjustment

Press the SET button (Horizontal)(Fig. 6 U).

●Each time the button is pressed, the air direction range will change as follows:

1234

The remote control unit’s

display does not change.

En-11

To select SWING Operation

Press the SWING button (Fig. 6 V).

The SWING Display (Fig. 7 f) will light.

Each time the SWING button is pressed, the swing operation will change in the

following order.

To stop SWING Operation

Press the SWING button and select STOP.

Airflow direction will return to the setting before swing was begun.

SWING OPERATION

COIL DRY OPERATION

The Indoor unit can be dried by pressing the COIL DRY button on the Remote Control Unit so as to avoid going moldy and

restrain the breed of bacterium.

The COIL DRY Operation will operate for 20 minutes after pressing the COIL DRY button and it will stop automatically.

To select COIL DRY Operation

Press the COIL DRY button (Fig. 6 N) during operation or when

it stops.

The COIL DRY Display (Fig. 7 d) will light.Then it will disappear after 20 minutes.

To cancel COIL DRY Operation

Press the START/STOP button (Fig. 6 S) during COIL DRY

Operation.

The COIL DRY Display (Fig. 7 d) will go out .Then the operation stops.

About COIL DRY Operation

●Press the COIL DRY button again during COIL DRY Operation, COIL DRY Opera-

tion can be reset.

●The COIL DRY Operation cannot get rid of the existed mould or bacterium, and it

has no sterilization effect either.

Begin air conditioner operation before performing this procedure.

Up/down swing operation Left/right swing operation

Swing operation stops Up/down/left/right swing operation

About Swing Operation

● Up/down swing: Swing operation begins using the

following range according to the current airflow direc-

tion.

Airflow direction is 1–4 (for cooling, dry).

With the upper airflow-direction louver in the

horizontal position, the lower airflow-direction

louver moves (swings) to direct airflow to a wide

area.

Airflow direction is 3–6 (for heating).

With the airflow-direction louvers set for down-

ward or straight down airflow, airflow is directly

mainly at the floor.

● Left/right swing: The airflow-direction louvers move

(swing) in the left/right airflow direction.

● Up/down/left/right swing: The airflow-direction louvers

move (swing) in both the up/down and left/right airflow

directions.

●The SWING operation may stop temporarily when the

air conditioner’s fan is not operating, or when operating

at very low speeds.

●If the SET button(Vertical) is pressed during the up/

down swing operation, the up/down swing operation

will stop and if the SET button(Horizontal) is pressed

during the left/right swing operation, the left/right

swing operation will stop.

En-12

Cleaning the Intake Grille

1. Remove the Intake Grille.

1Place your fingers at both lower ends of the grille

panel, and lift forward; if the grille seems to catch

partway through its movement, continue lifting up-

ward to remove.

2Pull past the intermediate catch and open the Intake

Grille wide so that it become horizontal.

2. Clean with water.

Remove dust with a vacuum cleaner; wipe the unit with

warm water, then dry with a clean, soft cloth.

3. Replace the Intake Grille.

1Pull the knobs all the way.

2Hold the grille horizontal and set the left and right

mounting shafts into the bearings at the top of the

panel.

3Press the place where the arrow on the diagram indi-

cates and close the Intake Grille.

CLEANING AND CARE

●Before cleaning the air conditioner, be sure to turn it off and disconnect the Power Supply Cord.

●Be sure the Intake Grille (Fig. 1 8) is installed securely.

●When removing and replacing the air filters, be sure not to touch the heat exchanger, as per-

sonal injury may result.

CAUTION!

Cleaning the Air Filter

1. Open the Intake Grille, and remove the air

filter.

Lift up the air filter’s handle, disconnect the two lower

tabs, and pull out.

2. Remove dust with a vacuum cleaner or by

washing.

After washing, allow to dry thoroughly in a shaded place.

3. Replace the Air Filter and close the Intake

Grille.

1Align the sides of the air filter with the panel, and push

in fully, making sure the two lower tabs are returned

properly to their holes in the panel.

2Close the Intake Grille.

(For purposes of example, the illustration shows the unit

without Intake Grille installed.)

●Dust can be cleaned from the air filter either with a vacuum

cleaner, or by washing the filter in a solution of mild de-

tergent and warm water. If you wash the filter, be sure to

allow it to dry thoroughly in a shady place before rein-

stalling.

●If dirt is allowed to accumulate on the air filter, air flow

will be reduced, lowering operating efficiency and increas-

ing noise.

●During periods of normal use, the Air Filters should be

cleaned every two weeks.

●When used for extended periods, the unit may accumulate dirt inside, reducing its performance.We recommend that the

unit be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized service

personnel.

●When cleaning the unit’s body, do not use water hotter than 104 °F, harsh abrasive cleansers, or volatile agents like

benzene or thinner.

●Do not expose the unit body to liquid insecticides or hairsprays.

●When shutting down the unit for one month or more, first allow the fan mode to operate continuously for about one-half

day to allow internal parts to dry thoroughly.

Intake Grille

Air filter handle

Hooks (two places)

Intake

Grille

Hooks (two places)

Intake Grille

Mounting

shaft

Knob

Intake Grille

Bearing

Mounting shaft

Knob

Mounting

shaft

Knob

En-13

CLEANING THE PLASMA AIR CLEANING FILTER

CAUTION!

WARNING!

●Make sure the plasma filter unit is properly mounted before cleaning or performing other tasks

on it. If the unit is not properly mounted, it could fall off and cause damage or injury.

●You can be injured if you touch the heat exchanger when removing or installing the plasma filter

unit. Do not insert your fingers between the plasma filter unit and the heat exchanger.

Before cleaning the plasma filter unit, be sure to turn off the power supply to the air conditioner.

Electric shock may result.

Regarding the Air Cleaning check function

●This function is illustrated by the flashing of the AIR CLEAN Indicator Lamp (orange), indicating that the unit requires

maintenance.

After Air Cleaning Mode has been in use for approximately 400 hours, the AIR CLEAN Indicator Lamp (orange) will begin

to slowly flash (approximately once every 7 seconds). When this occurs, the unit requires maintenance.

After Air Cleaning Mode has been in use for approximately 500 hours, the AIR CLEAN Indicator Lamp (orange) will begin

to flash quickly (approximately once every 3 seconds). At this point, Air Cleaning will cease functioning. Please carry out

appropriate maintenance for the unit.

●Please carry out unit maintenance every 6 months.

●If a squeaking or chirping sound is heard, unit maintenance needs to be carried out, even if the AIR CLEAN Indicator Lamp

(orange) is not flashing.

Cleaning the dust collection unit

1. Open the intake grille and remove the air

filter on the right.

●Please consult the instructions for cleaning the air

filter on page 12.

4. Wash with water and dry.

1Soak the plasma filter unit in warm water (104 to

113˚F) for 10 to 15 minutes. If the plasma filter unit is

extremely dirty, extremely dilute a mild synthetic laun-

dry detergent (low alkalinity or isotope detergent) to

15 times the standard concentration and allow the

plasma filter unit to soak in it.

2Gently move up and down and to the right and left. A

soft sponge can also be used to wipe the surface.

3Rinse with clean water.

4Shake the plasma filter unit to drain off the water. (If

the plasma filter unit is extremely dirty, repeat Steps

1through 4two or three more times.)

Place the plasma filter unit in the shade and allow it

to dry completely.

●Only use a mild synthetic laundry detergent (low

alkalinity or isotope detergent).

● Never disassemble the plasma filter unit.

● Never soak the plasma filter unit in hot water.

● Never wipe the plasma filter unit with a scrub brush

or other hard or abrasive items. This will damage

the honey comb filter.

●Never insert a brush into the inside of plasma filter

unit for washing.This will damage the internal parts

and cause malfunctioning of the plasma filter unit.

●Never use dryer or other device to blow hot air on

the plasma filter unit. This will cause deformation

or other damage.

●Before re-installing the unit, please wait until it is

completely dry. If the unit is installed when still wet

and then put into operation, the OPERATION Indi-

cator Lamp (red) and the TIMER Indicator Lamp

(green) will flash and Air Cleaning will stop.

handle

2. Remove the dust collection unit.

Securely grasp the dust collection unit by the handle and

pull it out (as shown by the arrow).

(The above figure is only for reference, so the intake grille

is not included).

3. Remove the air cleaning & deodorizing fil-

ter from the cleaning unit.

1Open the filter case at the rear of cleaning unit.

2Remove the air cleaning & deodorizing filter.

Claw Claw

Filter case

Air cleaning &

deodorizing filter

En-14

Cleaning the dust collection unit

5. Install the unit.

(The above figure is only for reference, so the intake grille

is not included.)

●Please ensure that the dust collection unit is

completely dry before installing.

●After installing the dust collection unit, please

ensure that it has been inserted fully into its place.

If it has not been installed correctly, the OPERATION

Indicator Lamp (red) and the TIMER Indicator Lamp

(green) will flash, and Air Cleaning will stop.

6. Install the air filter.

●

Please consult instructions for cleaning the air filter

on page 12.

7. Close the intake grille.

Push the intake grill in at 4 points (the two ends of its

lower side as well as two center points of the lower side,

as shown in the figure) to close it.

●If, after cleaning the dust collection unit, the

operation indicator lamp and the timer indicator

lamp flash during Air Cleaning, please ensure that

the unit is not damp and that the intake grille is

properly closed.

●If, after having checked that the unit is fully dry and

that the intake grille is closed properly, the indicator

lamps continue to flash, the dust collection unit may

be damaged. Please consult an authorised dealer

to obtain a replacement.

Align the two ends of the dust collection

unit with the guide rail and slide in.

Slide in until it clicks.

Guide rail

“Click”

Please ensure that the intake grille is

closed properly.

WARNING!

● Be sure the Intake Grille (Fig. 4 8) is installed

securely.

En-15

Air-cleaning and Deodorizing filter

maintenance

As well as ensuring the maintenance of the dust collecting

unit, please also take care of the filter.

(Please carry out maintenance on the filter every 6 months.)

1. Open the intake grille and remove the air

filter from the right side.

●

Please consult step 1 of cleaning the air filter on page 12.

2. Take out the unit and remove the Air-

cleaning and Deodorizing filter.

● Please consult steps 2 and 3 of cleaning the air filter

on page 13.

3. Air-dry after washing.

1Wash using lukewarm or warm water. If quite dirty,

wash using a mild detergent.

2Rinse it under running water.

3Allow it to dry thoroughly in a shaded place.

4. Install the Air-cleaning and Deodorizing

filter.

●Please consult the instructions on how to install the

filter on page 15.

5. Install the air filter and close the intake

grille.

●Please consult step 3 of cleaning the air filter on

page 12.

Regarding the Air-cleaning and Deodorizing filter

●Please change the filter approximately every 2 years to

ensure good Air-cleaning performance. (This is only

possible if the filter is cleaned once every six months)

●Please only install filters that are licensed by our

company.

●Regarding storage and care of the filter, please avoid

exposing it to high temperatures and high humidity.

Also, use it as soon as possible after opening its

packaging.

Hook

Filter case

Filter Case

Hook

Hook Hook

“Click”

❇When removing the filter, please follow these

steps backwards.

How to install or remove the Air-

cleaning and Deodorizing filter

1. Remove the dust-collecting unit.

●Please consult steps 1 and 2 of cleaning the dust-

collecting unit on page 13.

2. Install or remove the Air-cleaning and

Deodorizing filter into the unit.

1Open the filter case inside the dust-collecting unit.

2Insert or remove the Air-cleaning and Deodorizing filter

into the dust-collecting unit.

3Close the filter case.

3. Install the dust-collection unit.

● Please consult steps 5, 6 and 7 of cleaning the dust-

collection unit on page 14.

Filter

●Please ensure that the filter case is properly

closed. If the filter case is not properly closed,

the filter could fall out.

“Click”

When changing the filter, please make sure you purchase

the correct model (UTR

–

FA15).

Please do not rub the filter, it may cause its Air-

cleaning performance to be reduced.

Remove

Install

●Please place the air cleaning & deodorizing

filter, with the black surface upward.

En-16

TROUBLESHOOTING

WARNING!

Symptom

Doesn’t operate immedi-

ately:

Noise is heard:

Smells:

Mist or steam are

emitted:

Airflow is weak or stops:

Water is produced from

the outdoor unit:

The AIR CLEAN Indicator

Lamp (orange) will begin

to slowly flash (as shown

in the figure):

The AIR CLEAN Indicator

Lamp (orange) will begin

to flash quickly (as shown

in the figure):

Problem

●If the unit is stopped and then immediately started again, the com-

pressor will not operate for about 3 minutes, in order to prevent

fuse blowouts.

●

Whenever the Power Supply Plug is disconnected and then re-

connected to a power outlet, the protection circuit will operate for

about 3 minutes, preventing unit operation during that period.

●During operation and immediately after stopping the unit, the

sound of water flowing in the air conditioner’s piping may be

heard. Also, noise may be particularly noticeable for about 2 to 3

minutes after starting operation (sound of coolant flowing).

●During operation, a slight squeaking sound may be heard.This is

the result of minute expansion and contraction of the front cover

due to temperature changes.

●

During Heating operation, a sizzling sound may be heard occasional.

This sound is produced by the Automatic Defrosting operation.

●Some smell may be emitted from the indoor unit. This smell is

the result of room smells (furniture, tobacco, etc.) which have

been taken into the air conditioner.

●During Cooling or Dry operation, a thin mist may be seen emitted

from the indoor unit.This results from the sudden Cooling of room

air by the air emitted from the air conditioner, resulting in con-

densation and misting.

●During Heating operation, the outdoor unit’s fan may stop, and

steam may be seen rising from the unit.This is due to Automatic

Defrosting operation.

●When Heating operation is started, fan speed is temporarily very

low, to allow internal parts to warm up.

●During Heating operation, if the room temperature rises above

the thermostat setting, the outdoor unit will stop, and the indoor

unit will operate at very low fan speed. If you wish to warm the

room further, set the thermostat for a higher setting.

●During Heating operation, the unit will temporarily stop opera-

tion (between 7 and 15 minutes) as theAutomatic Defrosting mode

operates. During Automatic Defrosting operation, the OPERATION

Indicator Lamp will flash.

●The fan may operate at very low speed during Dry operation or

when the unit is monitoring the room’s temperature.

●During SUPER QUIET operation, the fan will operate at very low

speed.

●In the monitor AUTO operation, the fan will operate at very low

speed.

●During Heating operation, water may be produced from the out-

door unit due to Automatic Defrosting operation.

●After approximately 400 hours of Air Cleaning Mode use, the AIR

CLEAN Indicator Lamp will begin to flash slowly (as shown in the

figure). When this occurs, please stop the system, remove the

mains socket and carry out maintenance on the dust collecting

unit's air filter.

●After approximately 500 hours of Air Cleaning Mode use, the AIR

CLEAN Indicator Lamp will begin to flash quickly (as shown in

the figure). At this point, Air Cleaning will stop functioning. Please

stop the system, remove the mains socket and carry out mainte-

nance on the dust collecting unit's air filter.

See Page

—

13 - 14

NORMAL

FUNCTION

In the event of a malfunction (burning smell, etc.), immediately stop operation, turn off the elec-

trical breaker or disconnect the power supply plug, and consult authorized service personnel.

Merely turning off the unit’s power switch will not completely disconnect the unit from the power

source. Always be sure to turn off the electrical breaker or disconnect the power supply plug to

ensure that power is completely off.

Before requesting service, perform the following checks:

En-17

TROUBLESHOOTING

Symptom

Doesn’t operate at all:

Poor Cooling performance:

The unit operates

differently from the Remote

Control Unit’s setting:

See Page

—

8 - 9

—

CHECK ONCE

Items to check

●Is the Power Supply Plug disconnected its outlet?

●Has there been a power failure?

●Has a fuse blown out, or a circuit breaker been tripped?

●Is the timer operating?

●Is the Air Filter dirty?

●Air the air conditioner’s intake grille or outlet port blocked?

●Did you adjust the room temperature settings (thermostat) cor-

rectly?

●Is there a window or door open?

●In the case of Cooling operation, is a window allowing bright sun-

light to enter? (Close the curtains.)

●In the case of Cooling operation, are there heating apparatus and

computers inside the room, or are there too many people in the

room?

●Is the unit set for SUPER QUIET operation?

●Are the Remote Control Unit’s batteries dead?

●Are the Remote Control Unit’s batteries loaded properly?

OPERATING TIPS

If the problem persists after performing these checks, or if you notice burning smells, or both the ORERATION Indicator Lamp

(Fig. 3 ) and the TIMER Indicator Lamp (Fig. 3 6) flashes, or only the TIMER Indicator Lamp (Fig. 3 6) flashes, immediately

stop operation, disconnect the Power Supply, and consult authorized service personnel.

Operation and Performance

Heating Performance

●This air conditioner operates on the heat-pump princi-

ple, absorbing heat from outdoor air and transferring that

heat indoors. As a result, the operating performance is

reduced as outdoor air temperature drops. If you feel that

insufficient heating performance is being produced, we

recommend you use this air conditioner in conjunction

with another kind of heating appliance.

●Heat-pump air conditioners heat your entire room by

recirculating air throughout the room, with the result that

some time may be required after first starting the air con-

ditioner until the room is heated.

Microcomputer-controlled Automatic Defrosting

●When using the Heating mode under conditions of low

outdoor temperature and high humidity, frost may form

on the outdoor unit, resulting in reduced operating per-

formance.

In order to prevent this kind of reduced performance, this

unit is equipped with a Microcomputer-controlled Auto-

matic Defrosting function. If frost forms, the air condi-

tioner will temporarily stop, and the defrosting circuit will

operate briefly (for about 7-15 minutes).

During Automatic Defrosting operation, the OPERATION

Indicator Lamp (red) will flash.

AUTO Restart

In Event of Power Interruption

●The air conditioner power has been interrupted by a

power failure. The air conditioner will then restart auto-

matically in its previous mode when the power is restored.

●Operated by setting before the power failure.

●

If a power failure occurs during TIMER operation, the timer

will be reset and the unit will begin (or stop) operation at the

new time setting. In the event that this kind of timer fault

occurs the TIMER Indicator Lamp will flash (see Page. 3).

●Use of other electrical appliances (electric shaver, etc.) or

nearby use of a wireless radio transmitter may cause the

air conditioner to malfunction. In this event, temporarily

disconnect the Power Supply Plug, reconnect it, and then

use the Remote Control Unit to resume operation.

Other manuals for Inverter Halcyon ASU24RLXQ

This manual suits for next models

Table of contents

Other Fujitsu Air Conditioner manuals

Fujitsu

Fujitsu AS* A09LEC Original operating manual

Fujitsu

Fujitsu ASYG09LLCB Original operating manual

Fujitsu

Fujitsu AUU7RLF Service manual

Fujitsu

Fujitsu ARYG45LMLA User manual

Fujitsu

Fujitsu AIRSTAGE AJY126GALH User manual

Fujitsu

Fujitsu ABT series User manual

Fujitsu

Fujitsu AGYG09LVCB User manual

Fujitsu

Fujitsu ARY9LUAB User manual

Fujitsu

Fujitsu ASUH18LPAS Service manual

Fujitsu

Fujitsu ASTG24JF User manual

Fujitsu

Fujitsu ARYG30LMLE User manual

Fujitsu

Fujitsu General ARXG45KHTB User manual

Fujitsu

Fujitsu ARTG30LHTA User manual

Fujitsu

Fujitsu 9319357041 User manual

Fujitsu

Fujitsu ASY18LMA-W User manual

Fujitsu

Fujitsu AirStage AJ 072GALDH Series User manual

Fujitsu

Fujitsu Inverter ASBA30JFC User manual

Fujitsu

Fujitsu AU* G24LVLA Original operating manual

Fujitsu

Fujitsu ABY45LBAG User manual

Fujitsu

Fujitsu ASYG07KMCC Service manual

Fujitsu

Fujitsu ASYG07KPCA Service manual

Fujitsu

Fujitsu AUT Series User manual

Fujitsu

Fujitsu ASYG07LMCA User manual

Fujitsu

Fujitsu ABYA45LCT User manual

Popular Air Conditioner manuals by other brands

LG AB-H1208VA0 Service manual

Daikin

Daikin FDA125A5VEB Installer and user reference guide

NuAire

NuAire UNI-X Series installation manual

Gree

Gree E-TAC Installation and operation instructions

Innova

Innova IGZCAPS NI Series owner's manual

Argo

Argo Relax Service manual

PR KLIMA

PR KLIMA GPC10AL operating instructions

Daikin

Daikin RZQSG-LV1 Technical data

Soleus Air

Soleus Air GM-PAC-10E2 operating instructions

Panasonic

Panasonic CS-LZ9ZKA operating instructions

Daikin

Daikin RX15RMVJU installation instructions

Haier

Haier 1U71S2SS5FA installation manual

Frigidaire

Frigidaire FFMS121CQ10 installation manual

Frico

Frico AD100 Original instructions

Seeley

Seeley CP18CW1 owner's manual

DeLonghi

DeLonghi PAC N90E instruction manual

Chigo

Chigo CHV Mini Series Service manual

DeLonghi

DeLonghi Pinguino CT300H instructions

Fujitsu Inverter Halcyon ASU24RLXQ User manual

Popular Air Conditioner manuals by other brands