Fujitsu MB1500EB01 User manual

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 1 -
P
PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC C
M
MB B1 15 5E E0 0x xS SL L
M
MB B1 15 5E E0 0x xS SR R
-MB1500EB01-
-MB1500EB01
Q
-

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 2 -
Table of Contents
1.0 General Description ---------------3
2.0 Design kit content ---------------3
3.0 Setup ---------------3
4.0 Device information ---------------4
5.0 Evaluation board description ---------------5
5.1.Board circuit ---------------5
5.2.Board layout ---------------6
5.3.Components list ---------------7
6.0 Typical Test Data ---------------8
6.1.Measurement condition ---------------8
6.2.Measurement results ---------------8
6.3.Measurement wave form ---------------9
Phase Noise ---------------9
Spurious ---------------9
Lock up time ---------------10
7.0 Additional information ---------------11
Option1 MB1500EB00A ---------------11

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 3 -
General Description
The MB1500EB01 and MB1500EB01Q are the evaluation board for MB15E0xSL and MB15E0xSR.
The difference of the evaluation board part number is the package type. MB1500EB01 is for TSSOP
or SSOP package. MB1500EB01Q is for QFN package. You can evaluate almost performance for
PLL with the evaluation board. (MB1500EB01Q for MB15E03/E07SL only)
When evaluating MB15E0xSL and MB15E0xSR, you can measure the RF loop characteristics by
putting the VCO and the LPF components.
Each output pad for RF VCO output and the external input for REF, CLK, Data, LE are prepared on
the board. Thus it is easy to connect their input/output. VCO and loop filter are not help you on the
board, so you can mount whatever you want.
Regarding CLK, Data and LE input, Fujitsu prepares the software and the cable or the interface board.
This set (Soft ware&Cable) control the data on a PC easily. (The part number of the cable is
MB1500EB00A. The interface board is MB1500EB00)
The socket for IC is set on the board, by which you can try evaluating many samples.
1.0 Design Kit
The design kit includes the following items.
-Evaluation board with the socket for QFN package or SSOP package.
-Evaluation board manual
3.0 Set up
1.VCO and Loop filter
The VCO and LPF are not mounted on the board, so you mount them on the board.
2.REFin
Connect a signal generator or TCXO to the REF pad. If the TCXO module is used, remove the
51ohm resistor.
3.VCO output
Connect RFVCO output pad to the spectrum analyzer or the modulation domain analyzer.
*SMA connector is not mounted on RF VCO output pad.
4.CLK, Data, LE
Connect the output pin of printer port or the special cable through a PC to the pins of CLK,
Data and LE.
Fujitsu prepare the special cable for the Fujitsu’s software of writing data.
The part number is MB1500EB00A. If you need it, please contact the sales.
5.Vcc and Vp
Connect a DC power supply output to the Vcc and Vp pins.
Vcc and Vp must supply equal voltage. Even if either RF-PLLor IF-PLLis not used, power must
be supplied to both VccRF and Vp To keep them equal, it is recommended that the non-use PLLis
controlled by power saving function.

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 4 -
6.PLLIC
The socket is attached on the board. It helps you to measure many PLL samples.
7.Power saving switch
There is a switch to control of power saving mode on the board for SSOP package. You can switch
the power saving mode and the normal mode. Regarding the board for QFN package, there is no switch
for controlling Power saving. Please TP3 shorts to VCC or GND to operate PLL.
4.0 Device (PLLIC) information
The evaluation board, MB1500EB01 can evaluate the following devices.
P/N Data sheet number Function Feature
Japanese English
MB15E03SL DS04-21359-4 DS04-21359-5E 1.2G Integer Single PLL Low current
MB15E05SL DS04-21360-4 DS04-21360-5E 2.0G Integer Single PLL Low current
MB15E07SL DS04-21358-4 DS04-21358-5E 2.5G Integer Single PLL Low current
MB15E05SR DS04-21377-1 DS04-21377-2E 2.0G Integer Single PLL Low noise
MB15E06SR DS04-21379-1 DS04-21379-2E 3.0G Integer Single PLL Low noise
MB15E07SR DS04-21378-1 DS04-21378-3E 2.5G Integer Single PLL Low noise
You can down load the data sheet on the web site.
Fujitsu Electrical Device Group web: http://jp.fujitsu.com/fsl/
*The datasheet is not available for QFN version yet(MB15E03SL).

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 5 -
5.0 Evaluation board description
5.1.Board circuit
MB1500EB01 (SSOP package)
MB1500EB01Q (QFN package)

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 6 -
5.2.Board layout
MB1500EB01(SSOP package)
Top layer Bottom layer
MB1500EB01B(QFN package) MB15E07SL,MB15E03SL only
Top layer Bottom layer
LE
DATA
CLK
PS
Do
LD/fout
LD/fout
1pin
1pin
Vp
Vcc
OSCin
Vvco
VCO LPF
fin
LE
Data
Clock
OSCin
fin
ΦR ΦP
LPF area
V
CO area
OSCout
Vvco
Vcc
Vp
GND
Please connect between Do and LPF line.
ZC PS-Low
PS-High

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 7 -
Item P/N Description TP name Item P/N Description TP name
R0 ---- ---- C12 GRM188B11H102KA01D 1000pF
R1 MCR03EZHJ510 51ΩC27 GRM188B11H102KA01D 1000pF
R2 ---- ---- C28 GRM188B11H102KA01D 1000pF
R3 ---- ---- C29 ---- ----
R5 MCR03EZHJ180 18ΩC30 ---- ----
R6 MCR03EZHJ180 18ΩC31 ---- ----
R7 MCR03EZHJ180 18ΩC11A GRM188B11H102KA01D 1000pF
R8 0ΩC25A GRM188B11H102KA01D 1000pF
R9 ---- ---- C26A GRM188B11H102KA01D 1000pF
R10 0ΩC11B SVC1E106M 10uF/25V
R11 ---- ---- C25B SVC1E106M 10uF/25V
R12 0ΩC26B SVC1E106M 10uF/25V
R13 ---- ---- CN1 5045-03A connector
TP1 LC-22-G TP V VCO VCO
TP2 LC-2-G TP GND SMA1 TSSM-LR-PC
TP3 LC-22-G TP PS SMA2 TSSM-LR-PC
TP4 LC-22-G TP LD/fout SW0 G-13AP SW
TP5 LC-2-G TP GND SW1 G-13AP SW
TP6 LC-2-G TP φP
TP7 LC-2-G TP φR
TP8 LC-22-G TP OSCout
TP9 LC-22-G TP VP
TP10 LC-22-G TP VCC
TP11 LC-2-G TP GND
TP12 LC-22-G TP VCO SW
TP13 LC-22-G TP Do
5.2.Components list MB1500EB01(SSOP)
Item P/N Description
1 C1,C4,C5 MCH185C102K(ROHM) Cap.1000pF
2 C2,C3,C9 MSVC1C106M(NEC)
MCH185C102K(ROHM)
Cap.10uF
Cap.1000pF
3 R1 MCR03EZHJ510(ROHM) Res.51Ω
4 R2,R3,R4 MCR03EZHJ180(ROHM) Res.18Ω
5 SW1 G-13AP -
6 SMA1 REF input Open
7 SMA2 VCO output Open
7 TP1,TP2,TP3,TP4,TP5,TP6 LC-2-G -
8 U1 PLL IC Open
10 U2 RFVCO Open
12 R5,R6,C6,C7,C8 LPF Open
Components list MB1500EB01Q(QFN)
Note: Please note the following in case of using MB1500EB01Q.
-R1 with 51ohm is mounted on the board for connecting a signal generator instead of crystal oscillator.
If crystal oscillator is used, please remove R1.
-SW0 is to monitor Do waveform. If the closed loop with VCO is constructed, please connect between
Do and LPF line.
-SW1 is no mounted. If no high impedance mode is needed, please open.

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 8 -
6.0.Typical Test Data(Ex.MB15E07SR)
6.1Measurement Condition
The data is measured under GSM application using MB15E07SR which has the feature of low noise.
Power supply voltage: :Vcc=Vp=3.75V
Oscillator frequency: :fosc=13MHz
Charge pump current: :ICP=1.5mA
Comparison frequency: :fr=200kHz
VCO frequency: :fvco=1730MHz to 1805MHz
VCO gain :42MHz/V(Vvco=3.3V)
RF Loop filter
C6 C7 C8 R5 R6
CDMA 1000pF 0.015uF 120pF 2.7kΩ27kΩ
*The number of the components is based on the description in 5.0.
6.2 Typical Measurement Results
Parameter Measurement Condition
Lock up time 390us 1730MHz to 1805 MHz +/-1kHz
370us 1805MHz to 1730MHz +/-1kHz
Phase Noise -86.5dBc/Hz Offset 1kHz @1730MHz
Spurious -80.5dBc Offset 200kHz @1730MHz
Do VT(to VCO)
C7
R5
C6
R6
C8

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 9 -
6.3 Measurement wave form
Phase Noise
Spurious

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 10 -
Lock up time
1730MHz -> 1805MHz,within +/-1kHz
Lch ->Hch 390 us Hch ->Lch 375 us
1805MHz -> 1730MHz
,
within +
/
-1kHz

F
Fu uj ji it ts su u P PL LL L F Fr re eq qu ue en nc cy y S Sy yn nt th he es si iz ze er r I IC Cs s
M
MB B1 15 50 00 0E EB B0 01 1_ _0
01 1Q Q E Ev va al lu ua at ti io on n B Bo oa ar rd d M Ma an nu ua al l2012.Apr.Rev6.0
- 11 -
7.0 Additional information
Option
There are two types of Software and Hardware for setting serial data.
Fujitsu provides the software and hardware. The software can work under NT, 2000 and XP.
MB1500EB00A_Parallel port version
-Cable
-Software
-Manual