Fujitsu SK-96650_6A0_380-120PMC User manual

Fujitsu Semiconductor Europe
User Guide
FMEMCU-UG-960031-13
F²MC-16FX FAMILY
MB96650/6A0/6C0/380 SERIES
EVALUATION BOARD
SK-96650_6A0_380-120PMC
USER GUIDE

Change even page title here
Revision History
FMEMCU-UG-960031-13 - 2 - © Fujitsu Semiconductor Europe GmbH
Revision History
Date
Issue
13.04.2011
V1.0, SWi: First Release
06.06.2011
V1.1, Swi: JP47 added in description
Chapter 2.3: title changed
02.03.2011
V1.2, SWi: name convention
24.04.2012
V1.3, SWi: new chapter about CE conformity declaration
This document contains 39 pages.

Change odd page title here
Warranty and Disclaimer
© Fujitsu Semiconductor Europe GmbH - 3 - FMEMCU-UG-960031-13
Warranty and Disclaimer
The use of the deliverables (e.g. software, application examples, target boards, evaluation boards,
              Fujitsu
Semiconductor Europe GmbH ment and/or
the Sale and Purchase Agreement under which agreements the Product has been delivered, (ii) the
technical descriptions and (iii) all accompanying written materials.
Please note that the deliverables are intended for and must only be used for reference in an
evaluation laboratory environment.
The software deliverables are provided on an as-is basis without charge and are subject to
alterations. 
functionality, qualification and compliance with component specifications.
Regarding hardware deliverables, FSEU warrants that they will be free from defects in material and
workmanship under use and service as specified in the accompanying written materials for a duration
of 1 year from the date of receipt by the customer.
              
exclusive remedy shall be, at FSEU´s sole discretion, either return of the purchase price and the
license fee, or replacement of the hardware deliverable or parts thereof, if the deliverable is returned
               
transport. However, this warranty is excluded if the defect has resulted from an accident not
attributable to FSEU, or abuse or misapplication attributable to the customer or any other third party
not relating to FSEU or to unauthorised decompiling and/or reverse engineering and/or
disassembling.
FSEU does not warrant that the deliverables do not infringe any third party intellectual property right
(IPR). In the event that the deliverables infringe a third party IPR it is the sole responsibility of the
customer to obtain necessary licenses to continue the usage of the deliverable.
In the event the software deliverables include the use of open source components, the provisions of
the governing open source license agreement shall apply with respect to such software deliverables.
To the maximum extent permitted by applicable law FSEU disclaims all other warranties, whether
express or implied, in particular, but not limited to, warranties of merchantability and fitness for a
particular purpose for which the deliverables are not designated.
To the maximum extent per          
gross negligence. FSEU is not liable for consequential damages.
Should one of the above stipulations be or become invalid and/or unenforceable, the remaining
stipulations shall stay in full effect.
The contents of this document are subject to change without a prior notice, thus contact FSEU about
the latest one.

Change even page title here
Contents
FMEMCU-UG-960031-13 - 4 - © Fujitsu Semiconductor Europe GmbH
Contents
REVISION HISTORY............................................................................................................2
WARRANTY AND DISCLAIMER .........................................................................................3
CONTENTS..........................................................................................................................4
1OVERVIEW......................................................................................................................6
1.1 Abstract...................................................................................................................6
1.2 Features..................................................................................................................7
1.3 General Description.................................................................................................8
1.3.1 MCU Clocks...............................................................................................8
1.3.2 RS-232 and LIN.........................................................................................8
1.3.3 CAN Bus....................................................................................................8
1.3.4 MCU Pins ..................................................................................................8
1.3.5 Power Supply ............................................................................................8
1.3.6 User Buttons..............................................................................................8
1.3.7 User LEDs and optional LCD.....................................................................8
1.3.8 I2C Bus......................................................................................................9
1.3.9 Emulator System .......................................................................................9
1.3.10 On-Chip Debug System (OCDS) ...............................................................9
2INSTALLATION.............................................................................................................10
2.1 Connection/Power-On...........................................................................................10
2.2 Default Jumper Settings........................................................................................11
2.3 Jumper Location....................................................................................................13
2.3.1 MB96650.................................................................................................13
2.3.2 MB966A0/6C0.........................................................................................14
2.3.3 MB96380.................................................................................................15
3JUMPERS AND SWITCHES..........................................................................................16
3.1 P17_0 (JP51)........................................................................................................16
3.2 Operating Mode (S1).............................................................................................16
3.3 Power Supply (S2, JP: 8, 15, 16, 17, 22, 61, 62, 63, 64) .......................................17
3.4 Subclock (JP: 1, 2)................................................................................................19
3.5 Analog Power Supply Voltage (JP: 11, 12, 13, 14)................................................20
3.6 Alarm Comparator (JP: 78)....................................................................................20
3.7 Reset Generation (JP: 33, 41, 46, 48)...................................................................21
3.8 User Buttons SW1, SW2, SW3, SW4, SW5, SW6 (JP: 3, 4, 5, 6, 7)......................22
3.9 I2C pull-up resistor (JP: 9, 10)................................................................................22
3.10 LIN / UART............................................................................................................23

Change odd page title here
Contents
© Fujitsu Semiconductor Europe GmbH - 5 - FMEMCU-UG-960031-13
3.10.1 LIN-UART 0 (JP: 19, 21, 23, 25, 27, 28, 29, 31) ......................................23
3.10.2 LIN-UART 2 (JP: 36, 37, 38, 39, 40, 42, 43, 45) ......................................24
3.11 CAN interfaces (JP: 24, 26, 34, 35).......................................................................24
3.12 3rd Monitor Voltage (JP24).....................................................................................25
4CONNECTORS..............................................................................................................26
4.1 Power connector (X7)............................................................................................26
4.2 MCU pin header connectors (X1 and X2)..............................................................26
4.3 LIN-UART connectors (X5, X9) .............................................................................26
4.4 CAN Connector (X6, X8).......................................................................................27
4.5 USER-LEDs & optional LC-Display (J1)................................................................28
4.6 In-Circuit-Programming Connector (X4) ................................................................29
4.7 Debug Connector (X12).........................................................................................29
4.8 Alarm Comparator Connector (J2).........................................................................29
4.9 External Supply Voltage Vin (J3)...........................................................................29
4.10 Vcc 5 Volts (J4).....................................................................................................30
4.11 Vcc 3.3 Volts (J5)..................................................................................................30
4.12 LIN Bus Inhibit (J6)................................................................................................30
4.13 LIN Bus Inhibit (J11)..............................................................................................30
4.14 VCC Connector (J7)..............................................................................................30
4.15 GND Connector (J8)..............................................................................................30
5PROGRAMMING THE INTERNAL FLASH MEMORY...................................................31
5.1 Asynchronous Mode..............................................................................................31
5.1.1 Reset (optional) .......................................................................................32
5.1.2 Flash Programming .................................................................................32
5.2 Synchronous Mode ...............................................................................................33
6ON-CHIP DEBUG HARDWARE CONFIGURATION...................................................... 34
7APPENDIX.....................................................................................................................35
7.1 Related Products...................................................................................................35
8INFORMATION IN THE WWW....................................................................................... 36
9EU-KONFORMITÄTSERKLÄRUNG / EU DECLARATION OF CONFORMITY............. 37
10CHINA-ROHS REGULATION........................................................................................38
11RECYCLING..................................................................................................................39

Change even page title here
Chapter 1 Overview
FMEMCU-UG-960031-13 - 6 - © Fujitsu Semiconductor Europe GmbH
1 Overview
1.1 Abstract
The SK-96650_6A0_380-120PMC is a multifunctional evaluation board for the Fujitsu
MB96600 Flash microcontroller MB96650, MB966A0 and MB966C0 Series as well as for the
MB96300 Flash microcontroller MB96380 Series.
It can be used stand-alone for software development and testing or as a simple target board
to work with the emulator system.
The board allows the designer immediately to start software development before his own
final target system is available.

Change odd page title here
Chapter 1 Overview
© Fujitsu Semiconductor Europe GmbH - 7 - FMEMCU-UG-960031-13
1.2 Features
Supports following Fujitsu products:
MB96600 series Microcontroller MB96650, MB966A0 and MB966C0 series with 120
pin PMC / M21 package
Embedded Emulator MB2100-01-E
MB96300 Microcontroller MB96380 Series with 120 pin PMC / M21 package
MB2198 Emulator System with the Probe Cable MB2198-16FX-120P-M21
9-15V unregulated external DC power supply
On-board 3.3V and 5.0V switching mode voltage regulators
Power-LEDs for all supply voltages
Onboard voltage supervisor monitor
In-Circuit serial Flash programming (UART0 or UART2)
All resources available for evaluation
All MCU pins routed to connectors
4 MHz main crystal
32 kHz crystal for sub clock operation
Two RS232- or LIN interfaces
Two CAN interfaces
3 V capable CAN, LIN, and RS232 transceivers
8 User LEDs
Optional: alphanumeric standard LC-Display connectable instead of LEDs
Reset button, Reset LED
5 User buttons
ON-Chip Debug Connector
This board must only be used for test applications
in an evaluation laboratory environment.

Change even page title here
Chapter 1 Overview
FMEMCU-UG-960031-13 - 8 - © Fujitsu Semiconductor Europe GmbH
1.3 General Description
The SK-96650_6A0_380-120PMC supports the F2MC-16FX MB96600 Flash microcontroller
MB96650, MB966A0 and MB966C0 Series as well as the F2MC-16FX Flash microcontroller
MB96380 Series with LQFP120-M21 (PMC) package.
It can be used as a stand-alone evaluation board or as a target board for the emulator
debugger.
1.3.1 MCU Clocks
The board is supplied with a socketed 4 MHz crystal as main oscillation source. Using the
internal PLL of the µC, internal clock rates up to 56 MHz can be achieved.
1.3.2 RS-232 and LIN
Two separate RS232 transceivers and two single-wire LIN-transceivers are available to
connect two out of three on-chip UARTs to 9-pin D-Sub connectors (X5, X9). The
transceivers generate the adequate RS232 levels for the receive (RXD) and transmit (TXD)
and LIN bus lines. In RS232 mode, either the DTR line or the RTS line can be selected with
jumpers (JP23 and JP38) to generate a system reset. The RTS signal can be shortcut to
CTS using the jumpers JP19 and JP36. Each of the four D-Sub connectors can be
configured as RS232 or LIN. The LIN Vs line can be powered by the unregulated supply
input of the board, so no additional supply is needed (JP28 and JP42).
All transceivers are fully 3.3V IO compatible to enable low voltage applications.
In-circuit programming (asynchronous) can be done via LIN-UART 0 and 2 (X5, X9).
1.3.3 CAN Bus
Two high-speed CAN transceivers (TLE6250GV33) can be connected to the CAN interfaces
of the MCU to allow easy connection to CAN networks.
All transceivers are fully 3.3V IO compatible to enable low voltage applications.
1.3.4 MCU Pins
All pins of the microcontroller except the oscillator pins X0/X1 and X0A/X1A as well as pin 62
are connected to edge connectors and are directly available to the user.
1.3.5 Power Supply
The on-board switching mode voltage regulators allow the user to connect an unregulated
DC input voltage of +9V to +15V, and supplies all voltages needed by the board and an
optional graphic sub-board. The regulators are rated with 3A (5V and 3.3V) and are
thermally protected against overload.
1.3.6 User Buttons
There are six push button switches on the board, which can be connected to input ports of
the microcontroller. This allows the user to evaluate external Interrupts, external timer trigger
-
button for the microcontroller, controlled by the supply monitor IC.
1.3.7 User LEDs and optional LCD
Eight user LEDs are connected to Port 09 and grounded by two 1k resistor networks (RN1,
RN2). If these LEDs are not required, these resistor networks can be removed to disconnect
the LEDs and to free the I/O port.

Change odd page title here
Chapter 1 Overview
© Fujitsu Semiconductor Europe GmbH - 9 - FMEMCU-UG-960031-13
1.3.8 I2C Bus
Additional 10 kOhm pull-up resistors can be connected to the I²C bus lines by setting the
according jumpers. JP9 is for SDA0 and JP10 for SCL0.
1.3.9 Emulator System
If the board is used as an emulator target board for the MB96300 super series, the
microcontroller must be removed from the socket and the corresponding probe cable has to
be mounted:
Table 1-1: Emulation System
1.3.10 On-Chip Debug System (OCDS)
If the On-Chip debugging on the MB96600 microcontroller is applied, then the embedded
emulator MB2100-01-E must be connected to the target board via SMA jack on the PCB.
Series
V-Chip
Probe cable
Socket
MB96380
MB96V300B
MB2198-16FX-120P-M21
NQPACK120SD, HQPACK120SD

Change even page title here
Chapter 2 Installation
FMEMCU-UG-960031-13 - 10 - © Fujitsu Semiconductor Europe GmbH
2 Installation
2.1 Connection/Power-On
Carefully remove the board from the shipping carton.
First, check if there are any damages before powering up the evaluation board.
For the power supply a DC input voltage of 9V –15V is recommended. The positive
voltage (+) must be connected to the center pin, and ground (GND) must be
connected to the shield of the connector X7!
After power-on (Switch S2 or JP22), the red power-on LEDs (LD9, LD10, LD11, and LD12)
should be lit. If the LEDs do not light up, switch off the power supply and check input polarity
and current capability of the DC supply used. Please do not look directly into the LEDs to
prevent harming your eyes.
The in-circuit programming allows the user to program own applications into the Flash
memory. The procedures for Flash programming are described in chapter 5.
If the board shall be used as an 16FX-MB96300 emulator target board, switch off the power
supply and remove the microcontroller from the socket. Now the probe cable can be
mounted on the socket. Take care of the pin 1 marking on the socket and fasten the probe
cable with the provided screws.
Do not use any other probe cable than MB2198-16FX-120P-M21 only!
Connect the probe cable to the MB2198-500-E emulation Adapter Board. Check all jumper
settings of the evaluation board, the Probe Cable, and the Adapter Board.
When turning on the system, be sure to use the following power-up sequence:
1. Power up the Emulator Main Unit (MB2198-01)
2. Power up the Adapter Board (MB2198-500), if needed
3. Power up the target Board (SK-96650_6A0_380-120PMC)
To turn off the system, switch off the components in reverse order, beginning with the target
Board.
Please refer to the corresponding user manuals and application notes for the emulator how
-LED of the emulator must be on.
In case of appropriation of the MB96600 microcontroller with the embedded emulator
MB2100-01-E it is referred to its operation manual.
Note:
Some customers experience connectivity problems when connecting the MCU into
the socket adapter. Only the small red screwdriver available in your box should be
used to connect the cover (HQPACK) onto the socket (NQPACK).
If the four screws are not tightening equally, then it may cause a poor contact.
Do not screw the cover too tight (max 0.054 Nm). If you have connectivity problems
then please loosen the screws and tighten again the screws equally.
Do not clean NQPACK, YQPACK, and YQSOCKET with steam. Cleaning material will
contaminate inside of connector.

Change odd page title here
Chapter 2 Installation
© Fujitsu Semiconductor Europe GmbH - 11 - FMEMCU-UG-960031-13
2.2 Default Jumper Settings
The following table lists all jumpers including its default setting and location on the starterkit.
Jumper
Description / Function
Type
Default Setting
Coordinates
MB96650
MB966A0
MB966C0
MB96380
JP1
X1A
Jumper 3 pin
1-2
1-2
1-2
J 10
JP2
X0A
Jumper 4 pin
1-2
1-2
1-2
J 10
JP3
Switch SW1 : INT0/NMI
Jumper 2 pin
Closed
Closed
Closed
H 6
JP4
Switch SW2 : INT5
Jumper 2 pin
Closed
Closed
Closed
H 6
JP5
Switch SW3 : TIN1
Jumper 2 pin
Closed
Closed
Closed
H 6
JP6
Switch SW4 : IN0 / TTG4/0
Jumper 2 pin
Closed
Closed
Closed
I 6
JP7
Switch SW5 : IN1 / TTG5/1
Jumper 2 pin
Closed
Closed
Closed
I 6
JP8
C pin
Jumper 2 pin
Closed
Closed
Closed
I 13
JP9
SDA0 pull-up
Jumper 2 pin
Open
Open
Open
L 15
JP10
SCL0 pull-up
Jumper 2 pin
Open
Open
Open
L 15
JP11
AVCC
Jumper 2 pin
Closed
Closed
Closed
I 14
JP12
AVRH
Jumper 2 pin
Closed
Closed
Closed
I 10
JP13
AVRL
Jumper 2 pin
Closed
Closed
Closed
J 14
JP14
AVSS
Jumper 2 pin
Closed
Closed
Closed
K 14
JP15
Voltage selection for MCUVCC
Solder JP 3 pin
1-2
1-2
1-2
K 15
JP16
MCUVCC
Jumper 2 pin
Closed
Closed
Closed
K 14
JP17
DVCC
Jumper 3 pin
1-2
1-2
1-2
L 12
JP18
DVSS
Jumper 2 pin
Closed
Closed
Closed
L 11
JP19
UART0 : CTS / RTS
Jumper 2 pin
Closed
Closed
Closed
I 3
JP20
CAN0 Transceiver type
Solder JP 3 pin
1-2
1-2
1-2
D 4
JP21
SIN0 : RS232 / LIN transceiver
Jumper 3 pin
1-2
1-2
1-2
H 5
JP22
Mains Switch
Jumper 2 pin
Open
Open
Open
L 16
JP23
UART0 : DTR / RTS
Jumper 3 pin
Open
Open
Open
H 3
JP24
CAN0 RxD
Jumper 2 pin
Closed
Closed
Closed
D 4
JP25
SOT0 : RS232 / LIN transceiver
Jumper 3 pin
1-2
1-2
1-2
H 5
JP26
CAN0 TxD
Jumper 2 pin
Closed
Closed
Closed
D 3
JP27
UART0 : RS232 / LIN
Jumper 3 pin
1-2
1-2
1-2
I 3
JP28
UART0 : LIN VBat
Jumper 2 pin
Open
Open
Open
H 3
JP29
UART0 : LIN-Enable
Jumper 2 pin
Open
Open
Open
I 3
JP30
LIN0 Transceiver type
Solder JP 3 pin
1-2
1-2
1-2
I 5
JP31
UART0 : LIN Master
Jumper 2 pin
Open
Open
Open
J 3
JP32
CAN1 Transceiver type
Solder JP 3 pin
1-2
1-2
1-2
G 4
JP33
Reset by UART 0 / 2
Jumper 3 pin
Open
Open
Open
I 5
JP34
CAN1 RxD
Jumper 2 pin
Closed
Closed
Closed
G 4
JP35
CAN1 TxD
Jumper 2 pin
Closed
Closed
Closed
G 3
JP36
UART2 : CTS / RTS
Jumper 2 pin
Closed
Closed
Closed
K 3
JP37
SIN2 : RS232 / LIN
Jumper 3 pin
1-2
1-2
1-2
J 5
JP38
UART2 : DTR / RTS
Jumper 3 pin
Open
Open
Open
K 3
JP39
SOT2 : RS232 / LIN
Jumper 3 pin
1-2
1-2
1-2
K 5
JP40
UART2 : RS232 / LIN
Jumper 3 pin
1-2
1-2
1-2
K 3
JP41
UART Reset / Inverter
Jumper 3 pin
Open
Open
Open
I 7
JP42
UART2 : LIN Vbat
Jumper 2 pin
Open
Open
Open
K 3
JP43
UART2 : LIN-Enable
Jumper 2 pin
Open
Open
Open
K 3
JP44
LIN2 Transceiver type
Solder JP 3 pin
1-2
1-2
1-2
L 4
JP45
UART2 : LIN Master
Jumper 2 pin
Open
Open
Open
M 3
JP46
Direct Reset / Delayed
Solder JP 3 pin
1-2
1-2
1-2
J 7
JP47
Voltage Monitor
Solder JP 4 pin
2-4
2-4
2-4
J7
JP48
MCU Reset
Jumper 2 pin
Closed
Closed
Closed
J 8
JP51
P17_0
Jumper 2 pin
open
open
Closed
K10

Change even page title here
Chapter 2 Installation
FMEMCU-UG-960031-13 - 12 - © Fujitsu Semiconductor Europe GmbH
Jumper
Description / Function
Type
Default Setting
Coordinates
MB96650
MB966A0
MB966C0
MB96380
JP61
DVCC Pin 53
Jumper 2 pin
Open
Closed
Closed
K11
JP62
DVSS Pin 54
Jumper 2 pin
Open
Open
Closed
K11
JP63
DVCC Pin 41
Jumper 2 pin
Open
Open
Closed
K12
JP64
DVSS Pin 42
Jumper 2 pin
Open
Closed
Closed
K12
JP78
ALARM0
Jumper 2 pin
Closed
Closed
Closed
L 13
Table 2-1: Jumper Settings

Change odd page title here
Chapter 2 Installation
© Fujitsu Semiconductor Europe GmbH - 13 - FMEMCU-UG-960031-13
2.3 Jumper Location
The following figures show the silk plot of the starter-kit with marked default jumper settings
depending on the microcontroller series.
2.3.1 MB96650
A
B
C
D
E
F
G
H
I
J
K
L
M
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
19
19
20
A
B
C
D
E
F
G
H
I
J
K
L
M
20
Figure 2-1: Default Jumper Setting with MB96650

Change even page title here
Chapter 2 Installation
FMEMCU-UG-960031-13 - 14 - © Fujitsu Semiconductor Europe GmbH
2.3.2 MB966A0/6C0
A
B
C
D
E
F
G
H
I
J
K
L
M
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
19
19
20
A
B
C
D
E
F
G
H
I
J
K
L
M
20
Figure 2-2: Default Jumper Setting with MB966A0/6C0

Change odd page title here
Chapter 2 Installation
© Fujitsu Semiconductor Europe GmbH - 15 - FMEMCU-UG-960031-13
2.3.3 MB96380
A
B
C
D
E
F
G
H
I
J
K
L
M
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
19
19
20
A
B
C
D
E
F
G
H
I
J
K
L
M
20
Figure 2-3: Default Jumper Setting with MB96380

Change even page title here
Chapter 3 Jumpers and Switches
FMEMCU-UG-960031-13 - 16 - © Fujitsu Semiconductor Europe GmbH
3 Jumpers and Switches
This chapter describes all jumpers and switches that can be modified on the evaluation
board. The default setting of a jumper is highlighted by a grey shaded area. When the
settings depend on the microcontroller, then for each derivate a column with the respective
settings is listed.
3.1 P17_0 (JP51)
Depending on the MCU and the operation mode the MCU the connection between pin 63
and DIP switch is closed.
JP50: Connects DIP switch to temporary mode pin P17_0 (MB96300: MD1)
Jumper
Setting
Description
MB96650
MB966A0
MB966C0
MB96380
JP51
(P17_0)
Closed
Closed
Closed
Pin 63 connected to DIP Switch S1
Open
Open
Open
Pin 63 disconnected to DIP Switch S1
Table 3-1: P17_0 Jumper Configuration
3.2 Operating Mode (S1)
This switch controls the MCU operation mode after Reset.
Please take care of the following mode settings:
DIP switch
Setting
Logical value
S1-1
(MB96600:DEBUG
I/F, MB96300: MD0)
ON (closed)
0 (low)
OFF (open)
1 (high)
S1-2
(MB96600: P17_0,
MB96300: MD1)
ON (closed)
0 (low)
OFF (open)
1 (high)
S1-3
(MB96600: MOD,
MB96300: MD2)
ON (closed)
0 (low)
OFF (open)
1 (high)
S1-4
(Not used)
ON (closed)
Not connected
OFF (open)
Not connected
Table 3-2: MCU Operating Mode

Change odd page title here
Chapter 3 Jumpers and Switches
© Fujitsu Semiconductor Europe GmbH - 17 - FMEMCU-UG-960031-13
Note: JP51  Note: JP51 closed
Figure 3-1: MCU mode switch: RUN mode (Fixed Vector Mode)
Note: JP51  Note: JP51 closed
Figure 3-2: MCU mode switch: Flash Programming mode
3.3 Power Supply (S2, JP: 8, 15, 16, 17, 22, 61, 62, 63, 64)
The on-board voltage regulator provides stabilized 5V *1 and 3.3V supplies to the MCU *1 and
peripherals. Even though they are thermally protected against overload, care must be taken
when supplying current for additional circuitry.
The LIN Vs line can be connected directly to the input supply of the board by jumpers. In this
case, the input voltage to the board has to be suitable for the connected bus devices (mostly
around 12V). Since there is a protection diode between Vin and Vs, it is not possible to
power the board over the LIN bus.
S2 Power Switch
JP8 Core power supply stabilization capacitor
JP15 Selects the power supply voltage for the microcontroller
JP16 Connects the power supply voltage to the microcontroller. An ampere meter can be
used instead for power consumption measurement.
JP17 Selects the Stepper Motor Driver Voltage (3.3V or 5V)
JP22 Jumper to override the power switch S2
JP61 Connects DVCC power supply with Pin 53
JP62 Connects DVSS power supply with Pin 54
JP63 Connects DVCC power supply with Pin 41
JP64 Connects DVSS power supply with Pin 42
On
Off
1 2 3 4
DEBUG I/F
P17_0
MD nc
DIP Switch:
RUN Mode On
Off
1 2 3 4
MD0MD1MD2nc
MB96600 MB96300
On
Off
1 2 3 4
DEBUG I/F
P17_0
MD nc
DIP Switch:
Programming
Mode
On
Off
1 2 3 4
MD0MD1MD2nc
MB96600 MB96300

Change even page title here
Chapter 3 Jumpers and Switches
FMEMCU-UG-960031-13 - 18 - © Fujitsu Semiconductor Europe GmbH
Jumper
Setting
Description
MB96650
MB966A0
MB966C0
MB96380
JP8
(C-pin)
Closed
Closed
Closed
An external capacitor is connected
Open
Open
Open
An external capacitor is not connected
JP15
(MCUVCC)
1 - 2
1 - 2
1 - 2
Power supply (VCC) for MCU is set to 5V
2 - 3
2 - 3
2 - 3
Power supply (VCC) for MCU is set to 3V3
JP16
(MCUVCC)
Closed
Closed
Closed
MCU is connected to VCC
Open
Open
Open
MCU is disconnected from VCC
JP17
(DVCC)
1 - 2
1 - 2
1 - 2
SMC (DVCC) supply voltage is set to 5V
2 - 3
2 - 3
2 - 3
SMC (DVCC) supply voltage is set to 3.3V
JP22
(Mains)
Closed
Closed
Closed
Board is always switched on
Open
Open
Open
Board power is controlled by switch S2
JP61
(DVCC_53)
Closed
Closed
Closed
Pin 53 is connected to SMC (DVCC)
supply voltage
Open
Open
Open
Pin 53 is disconnected to SMC (DVCC)
supply voltage
JP62
(DVSS_54)
Closed
Closed
Closed
Pin 54 is connected to SMC (DVSS)
supply voltage
Open
Open
Open
Pin 54 is disconnected to SMC (DVSS)
supply voltage
JP63
(DVCC_41)
Closed
Closed
Closed
Pin 41 is connected to SMC (DVCC)
supply voltage
Open
Open
Open
Pin 41 is disconnected to SMC (DVCC)
supply voltage
JP64
(DVSS_42)
Closed
Closed
Closed
Pin 42 connected to SMC (DVSS) supply
voltage
Open
Open
Open
Pin 43 is disconnected to SMC (DVSS)
supply voltage
Table 3-3: Power Supply Configuration
By default, all Board supplies are set to 5V.

Change odd page title here
Chapter 3 Jumpers and Switches
© Fujitsu Semiconductor Europe GmbH - 19 - FMEMCU-UG-960031-13
3.4 Subclock (JP: 1, 2)
All MB9600 microcontrollers and all MB96300 derivates with ordering post-
MB96F38xRW support a 32 kHz sub-clock (X0A, X1A), other devices like e.g. MB96F38xRS
do not support a sub-clock but will offer additional port-pins (e.g. P04_0, P04_1) instead.
Please check the related datasheet.
JP1: defines usage of pin 69 (X1A)
JP2: defines usage of pin 68 (X0A)
Jumper
Setting
Description
JP2
(X0A)
1-4
Pin 68 is connected to the 32 kHz sub-clock (X0A)
2-4
Pin 68 is used as port pin P04_0
3-4
Pin 68 is connected to GND (in case that subclock-
device is used, but no 32 kHz crystal is connected)
JP1
(X1A)
1-2
Pin 69 is connected to the 32 kHz sub-clock (X1A)
2-3
Pin 69 is used as port pin P04_1
Table 3-4: Subclock
Default: JP1: 1-2, JP2: 1-4
By default, the 32 kHz sub-clock-crystal is connected to the microcontroller.
4
3
1
2
Pin-out JP2:

Change even page title here
Chapter 3 Jumpers and Switches
FMEMCU-UG-960031-13 - 20 - © Fujitsu Semiconductor Europe GmbH
3.5 Analog Power Supply Voltage (JP: 11, 12, 13, 14)
The power supply as well as the positive reference voltage for the A/D-converter can be
provided internally or externally.
JP11, JP14 connects analog power supply voltages (AVcc and AVss)
JP12 connects the low pass filtered analog reference voltage AVRH to AVcc
JP13 connects the low pass filtered analog reference voltage AVRL to AVss
Jumper
Setting
Description
JP11
(AVcc)
Closed
AVcc is connected to Vcc
Open
AVcc is disconnected from Vcc
JP12
(AVRH)
Closed
AVRH is connected to AVcc
Open
AVRH defined by resistor network*1
JP13
(AVRL)
Closed
AVRL is connected to AVss
Open
AVRL defined by resistor network*1
JP14
(AVss)
Closed
AVss is connected to GND
Open
AVss is disconnected from GND
*1By default the resistor network (R16, R17, R20, R21) is not mounted on the board
Table 3-5: ADC Supply
Default: JP11, JP12, JP13, and JP14 are closed
By default, the A/D-converter supply and reference voltage is the same as the
microcontroller supply voltage.
Note:
If JP11 and JP14 are open, the user has to supply an adequate analog voltage supply (AVcc
and AVss) to the A/D-converter.
If JP12 and JP13 are open, the resistors R16, R17, R20, and R21 define AVRH and AVRL.
By default the resistor network (R16, R17, R20, and R21) is not mounted on the board.
3.6 Alarm Comparator (JP: 78)
Potentiometer RP2 is connected to ALARM0 in order to evaluate comparator 0 of the
microcontroller. Any voltage between VCC and GND can be set. Additionally the adjusted
voltage can be measured at connector J2.
JP78 One potentiometer can be connected to the ALARM0/AN8
Jumper
Setting
Description
JP78
(ALARM0)
Closed
Pin 26 (ALRAM0/AN8) of the MCU is connected to RP2
Open
Pin 26 (ALRAM0/AN8) of the MCU is not connected
Table 3-6: Alarm Comparator