Fujitsu PRIMERGY TX300 S5 User manual

Edition September 2009
PRIMERGY TX300 S5
Operating manual

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected]ujitsu.com.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2009 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability. The right to technical modification is reserved.
All hardware and software names used are trade names and/or trademarks of their respective
manufacturers.

TX300 S5 Operating manual
Contents
1 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.1 Concept and target groups for this manual . . . . . . . . . . 7
1.2 Documentation overview . . . . . . . . . . . . . . . . . . . . 8
1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.4 Notational conventions . . . . . . . . . . . . . . . . . . . . 19
1.5 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . 19
2 Installation steps, overview . . . . . . . . . . . . . . . . . . 23
3 Important information . . . . . . . . . . . . . . . . . . . . . 25
3.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 25
3.2 ENERGY STAR . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.3 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.4 FCC Class A Compliance Statement . . . . . . . . . . . . . 33
3.5 Transporting the server . . . . . . . . . . . . . . . . . . . . 34
3.6 Notes on installing in the rack . . . . . . . . . . . . . . . . . 35
3.7 Environmental protection . . . . . . . . . . . . . . . . . . . 36
4 Hardware installation . . . . . . . . . . . . . . . . . . . . . . 39
4.1 Unpacking the server . . . . . . . . . . . . . . . . . . . . . 40
4.2 Setting up the floorstand model . . . . . . . . . . . . . . . . 40
4.3 Installing/removing the rack model . . . . . . . . . . . . . . 42
4.3.1 Rack requirements . . . . . . . . . . . . . . . . . . . . . . . . 42
4.3.2 Installation in PRIMECENTER/DataCenter rack . . . . . . . . . 47
4.3.3 Installation in Classic Rack . . . . . . . . . . . . . . . . . . . 50
4.3.4 Installation in 3rd party racks . . . . . . . . . . . . . . . . . . 59
4.4 Connecting devices to the server . . . . . . . . . . . . . . . 60

Operating manual TX300 S5
Contents
4.5 Connecting the server to the mains . . . . . . . . . . . . . . 61
4.5.1 Using cable ties . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4.6 Notes on connecting/disconnecting cables . . . . . . . . . . 64
5 Starting up and operation . . . . . . . . . . . . . . . . . . . . 65
5.1 Access to the drives . . . . . . . . . . . . . . . . . . . . . . . 65
5.1.1 Access to the accessible drives (floorstand model) . . . . . . . . 65
5.1.2 Access to the HDD modules (floorstand model) . . . . . . . . . 67
5.2 Controls and indicators . . . . . . . . . . . . . . . . . . . . . 68
5.2.1 Front of server . . . . . . . . . . . . . . . . . . . . . . . . . . 68
5.2.1.1 ID card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.2.1.2 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.2.1.3 Indicators on the control panel . . . . . . . . . . . . . . . . 70
5.2.1.4 Indicators on the drives . . . . . . . . . . . . . . . . . . . . 71
5.2.2 Rear of server . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
5.2.2.1 Indicators on the connection panel . . . . . . . . . . . . . . 73
5.2.2.2 Indicator on hot-plug power supply unit . . . . . . . . . . . . 76
5.3 Switching the server on and off . . . . . . . . . . . . . . . . 77
5.4 Configuring the server . . . . . . . . . . . . . . . . . . . . . 79
5.4.1 Configuring the SAS/SATA RAID controller . . . . . . . . . . . . 79
5.4.2 Configuring the server and installing the operating system with
the ServerView Installation Manager . . . . . . . . . . . . . . . 80
5.4.3 Configuring the server and installing the operating system without
the ServerView Installation Manager . . . . . . . . . . . . . . . 81
5.5 Cleaning the server . . . . . . . . . . . . . . . . . . . . . . . 82
6 Property and data protection . . . . . . . . . . . . . . . . . . 83
6.1 BIOS Setup security functions . . . . . . . . . . . . . . . . . 83
7 Troubleshooting and tips . . . . . . . . . . . . . . . . . . . . 85
7.1 Power-on indicator remains unlit . . . . . . . . . . . . . . . . 85
7.2 Server switches itself off . . . . . . . . . . . . . . . . . . . . 86
7.3 Screen remains blank . . . . . . . . . . . . . . . . . . . . . . 86

TX300 S5 Operating manual
Contents
7.4 Flickering stripes on monitor screen . . . . . . . . . . . . . 87
7.5 No screen display or display drifts . . . . . . . . . . . . . . 87
7.6 Incorrect date and time . . . . . . . . . . . . . . . . . . . . 88
7.7 Hard disk drive error messages at system boot . . . . . . . 88
7.8 Added drive reported as defective . . . . . . . . . . . . . . 89
7.9 Error message on screen . . . . . . . . . . . . . . . . . . . 89
8 CSS components . . . . . . . . . . . . . . . . . . . . . . . . 91
8.1 Hot-plug components . . . . . . . . . . . . . . . . . . . . . 91
8.1.1 Hot-plug power supply units . . . . . . . . . . . . . . . . . . . 92
8.1.1.1 Replacing the hot-plug power supply unit . . . . . . . . . . 92
8.1.2 Hot-plug hard disk drives . . . . . . . . . . . . . . . . . . . . 93
8.1.2.1 3.5-inch HDD module and dummy module . . . . . . . . . . 94
8.1.2.2 2.5-inch HDD module and dummy module . . . . . . . . . . 95
8.1.2.3 Handling hard disk drives and HDD modules . . . . . . . . 96
8.1.2.4 Removing/installing the dummy module . . . . . . . . . . . 97
8.1.2.5 Installing the HDD module . . . . . . . . . . . . . . . . . . 98
8.1.2.6 Removing the HDD module . . . . . . . . . . . . . . . . . 100
8.1.3 Replacing hot-plug fan modules . . . . . . . . . . . . . . . . . 102
8.2 Non-hot-plug components . . . . . . . . . . . . . . . . . . . 105
8.2.1 Replacing a memory module . . . . . . . . . . . . . . . . . . 106
8.2.1.1 Removing and installing a fan bracket . . . . . . . . . . . . 106
8.2.1.2 Removing a defective memory module . . . . . . . . . . . 108
8.2.1.3 Installing a new memory module . . . . . . . . . . . . . . . 108
8.2.2 Replacing an expansion card . . . . . . . . . . . . . . . . . . 109
8.3 Opening/closing the housing . . . . . . . . . . . . . . . . . 111
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

TX300 S5 Operating manual 7
1 Preface
With top dual processor performance, the PRIMERGY TX300 S5 tower server
is an all-purpose server for medium sized companies and branches of large
enterprises. The system is ideal for use as a versatile business server for
business critical applications and dedicated tasks. Thanks to internal SAS/SATA
hard disk capacity of up to 6 or 8 TB, the PRIMERGY TX300 S5 is also suitable
for use as a platform for highly data intensive solutions. Furthermore, it is the
ideal solution for smaller mySAP installations and directory or cache services in
medium sized and large companies.
The PRIMERGY TX300 S5 offers a balanced architecture that incorporates
next generation main memory (DDR3) and I/O technologies (PCIe Gen2). The
HDD backplane is already provided for SAS 2.0 and 6 Gbit/s SAS and the
chipset prepared for the next generation of 6-core processors. High perfor-
mance, scalability, impressive reliability and excellent extension options are
combined in a powerful design.
The Cool-safe™ cooling concept with improved air flow cooling technology
(comb design) ensures the highest possible performance of the processors at
work; at the same time, the system is extremely reliable thanks to the reduced
heat dissipation.
The new PRIMERGY TX300 S5 can also be converted quickly and easily into a
space-saving rack system that only takes up 4 height units (HU).
1.1 Concept and target groups for this manual
This operating manual describes how to install, set up and operate your server.
This operating manual is intended for those responsible for installing the
hardware and ensuring that the system runs smoothly. It contains all the infor-
mation you need to put your PRIMERGY TX300 S5 into operation.
To understand the various expansion options, you will need to be familiar with
the fields of hardware and data transmission and you will require a basic
knowledge of the underlying operating system.

8 Operating manual TX300 S5
Documentation overview Preface
1.2 Documentation overview
More information on your PRIMERGY TX300 S5 can be found in the following
documents:
– "Quick Start Hardware - PRIMERGY TX300 S5" leaflet (only included as a
printed copy)
– "Quick Start Software - Quick Installation Guide" DVD booklet (only included
with the PRIMERGY ServerView Suite as a printed copy)
– "Safety notes and other important information" manual
– "Warranty" manual
– "PRIMERGY ServerView Suite Local Service Concept - LSC" manual
– "Returning used devices" manual
– "Helpdesk" leaflet
– Technical manual for the system board D2619
– "PRIMERGY TX300 S5 Server Operating Manual"
– "PRIMERGY TX300 S5 Server Options Guide"
– "D2619 BIOS Setup Utility for PRIMERGY RX300 S5 and TX300 S5"
manual
IPRIMERGY manuals are available in PDF format on the PRIMERGY
ServerView Suite DVD 2. The PRIMERGY ServerView Suite DVD 2 is
part of the PRIMERGY ServerView Suite supplied with every server.
If you no longer have the ServerView Suite DVDs, you can obtain the
relevant current versions using the order number U15000-C289.
The PDF files of the manuals can also be downloaded free of charge
from the Internet. The overview page showing the online documentation
available on the Internet can be found using the URL:
http://manuals.ts.fujitsu.com. The PRIMERGY server documentation can
be accessed using the Industry standard servers navigation option.

TX300 S5 Operating manual 9
Preface Features
Further sources of information:
– PRIMERGY Abbreviations and Glossary on the PRIMERGY
ServerView Suite DVD 2
– Manual for the monitor
– Documentation for the boards and drives
– Operating system documentation
– Information files in your operating system
1.3 Features
Customer Self Service (CSS)
The Fujitsu Technology Solutions Customer Self Service (CSS) concept
enables you to identify and replace the affected component yourself in the case
of certain error scenarios.
In the CSS concept, you can replace the following components yourself in the
event of an error:
– Hot-plug hard disk drives
– Hot-plug power supply units
– Memory modules
– System fans
– Expansion cards
For information on replacing these components, see chapter "CSS compo-
nents" on page 91.
CSS indicators on the control panel and on the back of the PRIMERGY server
provide you with information if a CSS event arises (for more information on the
behavior of these indicators, see chapter "Starting up and operation" on
page 65 and the "PRIMERGY ServerView Suite Local Service Concept - LSC"
manual on the PRIMERGY ServerView Suite DVD 2).
You can also fit your server with a ServerView Local Service Panel, which
enables you to identify the type of component affected by the error directly on
the server (for more information, see the "PRIMERGY ServerView Suite Local
Service Concept - LSC" manual on the PRIMERGY ServerView Suite DVD 2).
In addition, CSS errors are displayed in the ServerView Operations Manager,
the server management software from Fujitsu Technology Solutions.

10 Operating manual TX300 S5
Features Preface
In the event of errors, the ServerView Operations Manager refers you directly to
the affected component and its order information in the Illustrated Spares
catalog of the server in question.
System board
The features of the system board are described in the technical manual for the
system board D2619 for the hardware and in the BIOS Setup manual for the
firmware.
Trusted Platform Module (TPM)
A Trusted Platform Module (TPM) for safer storage of keys can be implemented
as an option. This module enables programs from third party manufacturers to
store key information (e.g. drive encryption using Windows Bitlocker Drive
Encryption).
The TPM is activated via the BIOS system (for more information, refer to the
Fujitsu Technology Solutions BIOS manual).
VCAUTION!
– When using the TPM, note the program descriptions provided by the
third party manufacturers.
– You must also create a backup of the TPM content. To do this, follow
the third party manufacturer's instructions. Without this backup, if the
TPM or the system board is faulty you will not be able to access your
data.
– If a failure occurs, please inform your service about the TPM
activation before it takes any action, and be prepared to provide them
with your backup copies of the TPM content.
Slots for expansion cards
The server can be flexibly expanded via seven slots (two PCIe Gen2 x8 and five
PCIe Gen2 x4). PCIe Gen2 doubles the bandwidth of currently existing PCIe
busses and allows improved system performance.
One of these slots is occupied with one of two possible SAS/SATA RAID
controllers.

TX300 S5 Operating manual 11
Preface Features
Fujitsu Technology Solutions offers a unique patented solution to deliver the
highest possible bandwidth with four PCIe Gen2 x8 slots: two of the four PCIe
Gen2 x4 slots can each be used as PCIe Gen2 x8 slots if the neighboring slot
is free.
Hard disk drives
The server is shipped with one of the following drive cages:
– For up to six 3.5-inch SAS/SATA hard disk drives:
Up to six SAS/SATA HDD modules can be used in the drive cage. Each HDD
module can accommodate a SAS/SATA hard disk drive with a maximum
height of 1 inch. The module is connected to the SAS/SATA backplane
wirelessly. This allows HDD modules to be plugged in and pulled out easily.
Optionally, you can also install a hard disk expansion box (Multibay 2, see
also section "Accessible drives" on page 12) (with up to two 3.5-inch
SAS/SATA HDD modules). The hard disk drives in this expansion box are
controlled by the 8-Port RAID Controller.
– For up to twelve 2.5-inch SAS/SATA hard disk drives:
Up to twelve SAS/SATA HDD modules can be used in the drive cage. Each
HDD module can accommodate an SAS/SATA hard disk drive with a 2.5-
inch format. The module is connected to the SAS/SATA backplane
wirelessly. This allows HDD modules to be plugged in or pulled out easily.
Optionally, you can also install a hard disk expansion box (with up to eight
2.5-inch SAS/SATA HDD modules). An additional SAS controller must be
installed in order to control the hard disk drives in this expansion box.

12 Operating manual TX300 S5
Features Preface
SAS/SATA RAID controller
The server is available with the following SAS/SATA RAID controllers for
operating the internal SAS/SATA hard disk drives:
– Modular RAID 0/1 controller with "Integrated Mirroring Enhanced"
(SAS IME)
RAID levels 0, 1 and 1E are supported for internal hard disk drive configura-
tions.
For more information on configuring the controller, see section "Configuring
the server" on page 79.
– Modular RAID 5/6 controller with "MegaRAID functionality"
(SAS MegaRAID)
RAID levels 0, 1, 10, 1E, 5, 50, 6 and 60 are supported for internal hard disk
drive configurations. As an option, a battery backup unit (BBU) can save the
memory content even if the power fails. Cache memory sizes of 256 Mbyte
and 512 Mbyte are available.
For more information on configuring the controller, see section "Configuring
the server" on page 79.
IFurther information on SAS/SATA RAID controllers is provided in the
"Modular RAID Controller Installation Guide" (on PRIMERGY
ServerView Suite DVD 2 under Industry Standard Servers - Expansion Cards
- Storage Adapters - LSI RAID / SCSI Controllers).
Further information on other SAS/SATA RAID controllers (e.g. for
operating external SAS/SATA hard disk drives or tape drives) is available
on PRIMERGY ServerView Suite DVD 2 under Industry Standard Servers
- Expansion Cards - Storage Adapters - LSI RAID / SCSI Controllers.
Accessible drives
The server has three 3.5-inch bays.
You can use these bays as follows:
– You can equip the individual bays with DVD drives or magnetic tape drives.
– You can install the Multibay 1 in the bottom bay. The Multibay 1 has bays for
a Slimline DVD drive and the ServerView Local Service Panel (LSP) or the
ServerView Local Service Display (LSD).

TX300 S5 Operating manual 13
Preface Features
– In the two lower bays, you can install the Multibay 2. The Multibay 2 has bays
for two additional 3.5-inch hard disk drives, a Slimline DVD drive and the
ServerView Local Service Panel (LSP) or the ServerView Local Service
Display (LSD).
– You can install the Multibay 1 in the bottom bay (see above) and the
expansion box for 2.5-inch SAS hard disk drives in the two upper bays (see
also section "Hard disk drives" on page 11).
Cooling and power supply
The Cool-safe™ cooling concept with split-level cooling (different fresh air
channels and fans for processors and memory modules) ensures maximum
performance of the new processors and maximum reliability by keeping all
components cool.
The efficient cooling system prevents high temperatures and results in lower fan
speed and less noise. The fans use less power.
Two versions of the server are available in terms of fan and power supply:
– Non-redundant configuration: The server has a hot-plug power supply unit
and three standard fan modules.
As an option, the power supply can be expanded with an extra power supply
unit to create a redundant power supply. If a power supply unit fails, the
redundant configuration assures continued operation. The defective power
supply unit can be replaced during operation (for further details see section
"Hot-plug power supply units" on page 92).
– Redundant configuration: The server has two hot-plug power supply units
and three redundant fan modules.
If a power supply unit or a fan module fails, the redundant configuration
assures continued operation. The defective power supply unit or fan module
can be replaced during operation (for further details, see sections "Hot-plug
power supply units" on page 92 and "Replacing hot-plug fan modules" on
page 102).

14 Operating manual TX300 S5
Features Preface
High level of availability and data security
When memory data is accessed, 1-bit errors are identified in the main memory
and automatically corrected with the error correcting code (ECC) method. The
patented memory scrubbing function regularly starts up the EDC mechanism,
ensuring continuous data integrity.
The memory modules used support SDDC technology (Chipkill™), which
further increases the effectiveness of memory error monitoring and correction.
Support is likewise provided for hot-spare memory technology, in which a
memory bank is used like a replacement bank. If a memory module fails, the
bank with the defective memory is automatically deactivated and the
replacement bank is activated (provided it has been configured for appropriately
in the BIOS). The deactivated memory bank is no longer used and the faulty
memory module can be replaced at the next opportunity. In order to be able to
use the hot-spare memory function, all occupied memory banks be equipped
with identical memory modules.
Memory modules can be protected against failure by mirroring (Memory
Mirroring). Memory Mirroring is roughly comparable to RAID level 1 for hard disk
arrays. The basic configuration requires two identical memory modules in two
different banks.
ASR&R (Automatic Server Reconfiguration and Restart) restarts the system in
the event of an error and automatically "hides" the defective system compo-
nents.
The PDA (Prefailure Detection and Analysis) technology from Fujitsu
Technology Solutions analyzes and monitors all components that are critical for
system reliability.
The SAS/SATA RAID controller supports different RAID levels and increase the
availability and data security of the system.

TX300 S5 Operating manual 15
Preface Features
iRMC S2 with integrated service LAN port
IThe features of the iRMC S2 Advanced Video Redirection and Remote
Storage are available as an option.
The iRMC S2 (integrated Remote Management Controller) is a BMC with
integrated service LAN port and expanded functionality that was previously only
available with additional plug-in cards. In this way, the iRMC S2 enables
complete control of PRIMERGY servers, regardless of system status, and thus
particularly the control of PRIMERGY servers that are in the "out-of-band"
system status.
Major functions supported by the iRMC S2 include the following:
●Browser access via iRMC S2-s own Web server
●Secure communication (SSH, SSL)
●Power Management for the managed server (depending on its system
status)
●Power Consumption Management
●Connecting virtual drives as remote storage
●Text-based and graphic console bypass (Advanced Video Redirection)
●Command Line Interface (CLI)
●Simple, interactive or script-based iRMC S2 configuration
●Customer Self Service (CSS)
●iRMC S2-s own user management
●Multi-computer, global iRMC S2 user administration using an LDAP
Directory Service
●Automatic network configuration via DNS / DHCP
●Power supply of the iRMC S2 via the system standby supply
●Full-coverage alarm management
●System Event Log (SEL) reading and processing
More information about the iRMC S2 can be found in the "iRMC S2 - integrated
Remote Management Controller" user’s guide (on the PRIMERGY
ServerView Suite DVD 2 under Industry Standard Servers - Software - PRIMERGY
ServerView Suite - Out-Of-Band Management).

16 Operating manual TX300 S5
Features Preface
Server management
Server management is implemented using the ServerView Operations Manager
supplied combined with PDA (Prefailure Detection and Analysis) technology
from Fujitsu Technology Solutions. PDA reports the threat of a system error or
overload at an early stage, allowing preventive measures to be taken.
The ServerView Operations Manager enables the management of all
PRIMERGY servers in the network via a central console. The ServerView
Operations Manager supports the following functions:
●Round-the-clock monitoring, regardless of server status
●High-performance, graphical console bypass (AVR) protected by
HTTPS/SSL (128-bit)
●Remote storage via USB
●Remote power on (Wake On LAN)
●Intrusion detection in the floorstand model
●Temperature monitoring of the CPU and the surrounding area
●Monitoring of PCI bus loading
●Detailed status and error reports for bus systems, processors and main
memory
●Watchdog timer for Automatic Server Reconfiguration and Restart (ASR&R)
in the event of failure of memory modules or processors
●Power monitoring
●End-of-life monitoring of fans with prompt notification before failure
●Watchdog timer for monitoring the operating system and applications with
ASR&R
Further information on the ServerView Operations Manager is provided in the
"ServerView Operations Manager - Server Management" User’s Guide (on the
PRIMERGY ServerView Suite DVD 2 under Industry Standard Servers - Software
- PRIMERGY ServerView Suite - Server Installation and Deployment).

TX300 S5 Operating manual 17
Preface Features
ServerView Installation Manager
You can configure the PRIMERGY server quickly and precisely with the
ServerView Installation Manager software provided. User-guided menus are
available for installing the server operating system (for further details see
section "Configuring the server" on page 79).
Service and support
PRIMERGY servers are service-friendly and modular, enabling quick and easy
maintenance.
The handles and locks (touch point) on the various hot pluggable components
are colored green to ensure simple and immediate recognition.
In order to prevent the components from being damaged by incorrect handling
when they are being installed and removed, the areas of all components that
can be touched without damaging them are also marked green.
PRIMERGY diagnostic LEDs fitted on the system board show which component
on the board (memory module, processor, fan) is not functioning properly.
The Flash EPROM program supplied with the Fujitsu Technology Solutions
utilities supports a fast BIOS update.
With the iRMC S2 (integrated Remote Management Controller) on the system
board, the PRIMERGY TX300 S5 server can also be maintained and serviced
remotely. This enables remote diagnosis for system analysis, remote configu-
ration and remote restart should the operating system or hardware fail.

18 Operating manual TX300 S5
Features Preface
ServerView Remote Management
ServerView Remote Management is the remote management solution from
Fujitsu Technology Solutions for PRIMERGY servers. ServerView Remote
Management and the relevant hardware components integrated on the system
board allow remote monitoring and maintenance as well as fast restoration of
operation in the event of errors.
Remote monitoring and maintenance avoids time-consuming and costly on-site
repairs and reduces service costs. This leads to a reduction in the total cost of
ownership and an excellent return on investment for the remote management
solution.
The administrator can access all system information and information from the
sensors such as fan speeds or voltages via the iRMC S2's Web interface (see
section "iRMC S2 with integrated service LAN port" on page 15). He can also
start the text-based or graphic console bypass (Advanced Video Redirection,
AVR) and get information about remote storage.
IThe features of the iRMC S2 Advanced Video Redirection and Remote
Storage are available as an option.
More information about the iRMC S2 can be found in the "iRMC S2 -
integrated Remote Management Controller" user’s guide (on the
PRIMERGY ServerView Suite DVD 2 under Industry Standard Servers -
Software - PRIMERGY ServerView Suite - Out-Of-Band Management).

TX300 S5 Operating manual 19
Preface Notational conventions
1.4 Notational conventions
The following notational conventions are used in this manual:
1.5 Technical data
Electrical data
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters and terms that are being
emphasized.
Êdescribes activities that must be performed in the order
shown.
VCAUTION! pay particular attention to texts marked with this symbol.
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips.
Rated voltage range 100 V - 240 V
Frequency 50 Hz - 60 Hz
Rated current with basic configuration 100 V - 240 V / 4.4 A - 1.5 A
Max. rated current 100 V - 240 V / 9.0 A - 5.0 A
Effective power max. 560 W
Apparent power max. 570 VA
Heat dissipation 2016 kJ/h (1911 btu/h)
Main power fuse 16 A
Protection class I

20 Operating manual TX300 S5
Technical data Preface
Compliance with regulations and standards
Product safety and ergonomics
International IEC 60950-1
Europe
Safety EN 60950-1
Ergonomics ISO 9241-3
EN 2941-3
EK1-ITB 2003:2007
UL 60950-1
USA / Canada CSA-C22.2 60950-1-03
Taiwan CNS 14336
China GB 4943
Electromagnetic compatibility
International CISPRA 24
Europe EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
ETS 300386
USA / Canada 47CFR part 15 Class A / ICES-003
Taiwan CNS 13438 Class A
China GB 9245 / GB 17625
Japan VCCI Class A / Jeida
CE marking to EU
directives
Low Voltage Directive 2006/95/EC
Electromagnetic compatibility 2004/108/EC