Furman PWRKITTL User manual

1. AC POWER CORD: This 10 ft. power cord is engineered to provide optimum power transfer, and shield-out performance robbing noise.
2. POWER INLET FACEPLATE: The unique twist-lock connector mates with the AC POWER CORD to provide a safe, secure and
listing agency compliant installation. The modular signal connection allows for a variety of installation options.
3. POWER OUTLET FACEPLATE: This modular interface has added noise filtration to eliminate any unwanted radiated interference.
4. POWER CORD (MPC-IEC): 24 inch IEC power cord.
AC POWER CORD WITH TWISTLOCK CONNECTOR
POWER
INLET
FACEPLATE
POWER
OUTLET
FACEPLATE
Plug into any receptacle for customized filtration needs.
Furman POWERKIT-TL Installation Instructions
POWERKIT-TL A four part kit designed specifically
to provide the ultimate power solution to remote
display devices within a home theater system.
Remote Display Device
(Plasma TV, DLP, etc.)
FURMAN POWER CONDITIONER 2
3
1
1690 Corporate Circle, Petaluma, CA 94954 • Fax [phone] • www.FurmanSound.com
080206
MPC-IEC
POWER CORD
4
Inwall
Romex
(not included)

Power Inlet Faceplate Installation Instructions
4 in.
3 3/4 in.
STEP 1:
Select a location close to the head-end source equipment. Cut a 4-inch wide by 3 3/4-inch high hole
in the wall. Feed the in wall Romex power cable (not included) through this opening and route them
to the location of the Power Outlet Faceplate.
NOTE: For new construction (pre-wire): Use a Carlon new-work electrical box (Model B122A).
A Carlon low voltage add-on bracket (Model SCIOOSC) may be used with the new-work box to
indicate the location and size of the opening needed in the drywall. The low-voltage bracket
may be left in place when installing the Inlet faceplate.
STEP 2:
Run the AC wires through the lower-left entry of the included outlet box. No more than 1-inch
of wire sheath should extend into the outlet box. 3-inches of wire should be able to extend
beyond the opening of the outlet box. Install the outlet box into the right side of the hole.
STEP 3:
Slide the included shrink-wrap tubing over the ground wire
if it is un-insulated. Strip 3/4-inch of insulation off the AC wires
and attach them to the twist-lock connector screw terminals.
Make sure to attach the wires to the correct terminal:
• Green/Ground wire to Center terminal with Green screw
• White wire to Silver terminal
• Black wire to Copper terminal
STEP 4:
Neatly fold the AC wires as you install the inlet faceplate into
the wall with the AC side fitting into the outlet box. Secure the
unit to the outlet box with the included screws.
NOTE: Only the right side screws are used to mount the inlet faceplate into the included outlet box.
The left side screws are for appearance only and are held on with the included plastic washers.
All four screws are used when mounting the protector to a new-work electrical box and low voltage
add-on bracket.
PAGE 2
1
2
3
4
CAUTION: Not for use in “Fire-Break” walls unless used in conjunction with signal-line modules!
NOTE:
To make installation easier, first connect the
included jumpers to the Twistlock Receptacle,
then use the included wire nuts to connect the
jumpers to the building wire. 14 gauge wire is
flexible enough to omit the jumpers. Just strip
1/4” of insulation off the AC wires and attach to
the screw terminals as labeled on the receptacle.
NOTE: Only for use with 15 Amp branch
circuits utilizing 14 or 12 gauge wire.
NOTE: Wire nuts are not recommended for
high-current applications such as powered
subwoofers.

Power Outlet Faceplate Installation Instructions
4 in.
3 3/4 in.
STEP 1:
Select a location close to the display device (Plasma TV, DLP, etc.). In the case of a wall-mounted
Plasma TV, this may be behind the display device and totally hidden from view once the Plasma TV
is mounted. Cut a 4-inch wide by 3 3/4-inch high hole in the wall for the in wall power cable (not included)
and signal wires (not included).
STEP 2:
Run the AC wires through the lower-left entry of the included outlet box. No more than 1 inch of wire
sheath should extend into the outlet box. 3 inches of wire should be able to extend beyond the opening
of the outlet box. Install the outlet box into the right side of the hole.
STEP 3:
Slide the included shrink-wrap tubing over the ground wire to prevent contact with the circuit board.
Use the included wire nuts to connect the wires.
Note: Wire nuts not recommended for high current applications such as powered subwoofers.
STEP 4:
Neatly fold the AC wires as you install the outlet faceplate into the wall with the AC side fitting into
the outlet box. Secure the unit to the outlet box with the included screws.
NOTE: Only the right side screws are used to mount the inlet faceplate into the included outlet box.
The left side screws are for appearance only and are held on with the included plastic washers.
All four screws are used when mounting the protector to a new-work electrical box and low voltage
add-on bracket.
PAGE 3
1
2
4
CAUTION: Not for use in “Fire-Break” walls!
NOTE: For new construction (pre-wire): Use a Carlon new-work electrical box (Model B122A).
A Carlon low voltage add-on bracket (Model SCIOOSC) may be used to indicate the size and location
of the opening needed in the drywall. The low-voltage bracket may be left in place when installing
the outlet faceplate.
3

Furman PowerKit-TL Product Warranty
LIMITED THREE YEAR WARRANTY
Furman Sound, Inc., having its principal place of business at 1690 Corporate Circle., Petaluma, CA 94954
("Manufacturer") warrants its PowerKit-TL (the "Product") as follows:
Manufacturer warrants to the original Purchaser of the Product that the Product sold hereunder will be free from
defects in material and workmanship for a period of three years from the date of purchase. The Purchaser of the
product is allowed fifteen days from the date of purchase to complete warranty registration by mail or on-line at the
Furman website. If the Product does not conform to this Limited Warranty during the warranty period (as herein above
specified), Purchaser shall notify Manufacturer in writing of the claimed defects. If the defects are of such type and
nature as to be covered by this warranty, Manufacturer shall authorize Purchaser to return the Product to the Furman
factory or to an authorized Furman repair location. Warranty claims should be accompanied by a copy of the original
purchase invoice showing the purchase date; this is not necessary if the Warranty Registration was completed either
via the mailed in warranty card or on-line website registration. Shipping charges to the Furman factory or to an autho-
rized repair location must be prepaid by the Purchaser of the product. Manufacturer shall, at its own expense, furnish
a replacement Product or, at Manufacturer's option, repair the defective Product. Return shipping charges back to
Purchaser will be paid by Manufacturer.
THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Manufacturer
does not warrant against damages or defects arising out of improper or abnormal use of handling of the Product;
against defects or damages arising from improper installation, against defects in products or components not manu-
factured by Manufacturer, or against damages resulting from such non-Manufacturer made products or components.
This warranty shall be cancelable by Manufacturer at its sole discretion if the product is modified in any way without
written authorization from Furman Sound. This warranty also does not apply to Products upon which repairs have
been affected or attempted by persons other than pursuant to written authorization by Manufacturer.
THIS WARRANTY IS EXCLUSIVE. The sole and exclusive obligation of Manufacturer shall be to repair or replace the
defective Product in the manner and for the period provided above. Manufacturer shall not have any other obligation
with respect to the Products or any part thereof, whether based on contract, tort, strict liability or otherwise. Under no
circumstances, whether based on this Limited Warranty or otherwise, shall Manufacturer be liable for incidental,
special, or consequential damages. Manufacturer's employees or representatives' ORAL OR OTHER WRITTEN STATE-
MENTS DO NOT CONSTITUTE WARRANTIES, shall not be relied upon by Purchaser, and are not a part of the contract
for sale or this limited warranty. This Limited Warranty states the entire obligation of Manufacturer with respect to the
Product. If any part of this Limited Warranty is determined to be void or illegal, the remainder shall remain in full force
and effect.
1690 Corporate Circle, Petaluma, CA 94954 • Fax [phone] • www.FurmanSound.com
080206