furniture123 AmberGlo AGL035 User manual

USER MANUAL
AmberGlo
Electric Fire
with LED Effect Lights
AGL035 / AGL036 / AGL037 / AGL053 / AGL054 /
AGL055 / AGL056 / AGL057
Thank you for choosing this AmberGlo electric flame effect heater.
Please read this guide aims to improve your understanding and appreciation of
your new heater, and please retain it for future reference.

2
CONTENTS
SAFETY
3
PARTS SUPPLIED
6
PRODUCT DIAGRAM
7
INSTALLATION
8
OPERATION
10
APP CONNECTION
12
CARE AND MAINTENANCE
19
BATTERY INFORMATION
19
TECHNICAL SPECIFICATION
19
TROUBLESHOOTING
20
SUPPORT
21
PRODUCT FICHE
22

3
SAFETY INFORMATION
When using electrical appliances, basic safety precautions should always be
followed, including the following:
•IMPORTANT: Read all instructions and warnings carefully before starting
installation. Failure to follow these instructions may result in a possible electric
shock or fire hazard and will void the warranty
•Before connecting the appliance, be sure that the mains voltage available matches
that specified on the rating plate, and that the outlet is suitably grounded.
•This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
•Children aged from 3 years and less than 8 years shall only switch on/off the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate, or clean the
appliance or perform user maintenance
•Children under 3 years should be kept away unless continuously supervised.
•Some parts of this product can become very hot and cause burns. Particular
attention has to be given where children and vulnerable people are present.
•If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
•WARNING: In order to avoid overheating, do not cover the heater.
•CAUTION: In order to avoid a hazard due to the inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external switching
device, such as a timer, or connected to a circuit that is regularly switched on and
off by the utility.
•Do not attempt to repair, disassemble or modify the appliance. This unit contains
no user-serviceable parts.
•Always unplug or disconnect the appliance from the mains power supply when not
in use, or when moving or cleaning it. Do not pull the cord to unplug the heater.
•Keep the heater clean. Do not allow any object to enter the ventilation or exhaust
opening as this may cause electric shock, fire, or damage to the heater.
•Do not use the appliance for other than its intended use. It is designed for
domestic indoor use only.
•There may be a trace of odour during the first few minutes of initial use, or after a
period of storage. This is normal and will quickly disappear.
•If the glass is damaged, do not use the heater in order to avoid a hazard.
•Avoid the use of an extension cord, as the cord may overheat and cause a risk of
fire.
•This fireplace is hot when in use. To avoid burns, do not let bare skin touch any
hot surfaces.
•Keep combustible materials, such as furniture, pillows, bedding, papers, clothes
and curtains at least 1 metre from the front and sides of this appliance.

4
•This appliance is designed for indoor use only and is not intended for use in
bathrooms, laundry areas and similar indoor locations. Never locate this
appliance where it may become exposed to water.
•Do not place this fire directly onto a carpeted surface to avoid discolouration due
to the heat.
•Do not run the cord under carpeting. Do not cover the cord with throw rugs,
runners or the like. Ensure the cord is kept away from traffic areas, and kept in a
position which would not present a trip hazard.
•To disconnect this appliance, Press the On/Off button to turn off, then remove the
plug from the outlet.
•This appliance has hot and arching or sparking parts inside. Do not use it in areas
where gasoline, paint, or any flammable liquids are used or stored.
•This appliance should not be used as a drying rack for clothing, nor should
Christmas stockings or decorations be hung on or near it.
•This electric fire is an instant heat source to warm up a room and is great for visual
room ambiance it doesn’t necessarily need to be used as a constant or permanent
source of heating for the home.
•Clean the fire regularly to prevent the build-up of hairs, dust or lint around the fire,
as this may cause the outlet to become blocked.
•Do not use aerosols or steam cleaners on or around the fire.
Manual Handling
•The heater must not be moved while in use. Please allow a suitable amount of
time for the unit to cool before attempting to move it.
•One person should be sufficient to lift the heater. If for any reason it is considered
too heavy then obtain assistance.
•When lifting always keep your back straight. Bend your legs and not your back.
•Avoid twisting at the waist. It is better to reposition your feet.
•Avoid upper body / top heavy bending. Always bend from the knees rather than
the waist. Do not lean forward or sideways whilst handling the heater.
•Always grip with the palm of the hand. Do not use the tips of fingers for support.
•Always keep the heater as close to the body as possible. This will minimize the
cantilever action.
•If required, use gloves to provide additional grip.
•Always use assistance if required.

5
ELECTRICAL SAFETY
The heater must not be located under an electrical socket; the socket must always
be accessible in order to disconnect the heater from the electrical supply for
maintenance and cleaning.
Important! This heater must be earthed. The mains supply must be safely routed
from the heater to an electrical socket.
If the supply cord is damaged, it must be replaced by the manufacturer,
service agent or a similarly qualified person in order to avoid a hazard.
This appliance is supplied with a BS1363 3 pin plug fitted with a 13 Amp fuse.
Should the fuse require replacement, it must be replaced with a fuse rated at 13
Amp and approved to BS1362.
In the event the mains plug has to be removed or replaced for any reason, please
note:
The wires in the mains lead on this appliance are coloured in accordance with the
following code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
As the colours may not
correspond with the
markings identifying the
terminals in your plug,
please proceed as follows.
•The green and yellow wire must be connected to the terminal in the plug
which is marked with the letter E or with the earth symbol or
coloured green and yellow.
•The blue wire must be connected to the terminal marked N or coloured
black.
•The brown wire must be connected to the terminal marked L or coloured
red.
Important - any cut off plug should be disposed of safely to prevent a hazard. There
is a danger of electric shock if a cut off plug is inserted into a socket outlet.

6
PARTS SUPPLIED
Please note: Models AGL035 and AGL056 do
not come with the log accessory.
BEFORE USE!
Before using the appliance for the first time, ensure that it has been fully unpacked,
and that all packaging has been disposed of properly to ensure it does not present a
risk to children of animals.
Due to the size and weight of the fire, we would
advise on 2 people carrying out installation to prevent
injury or damage.
Fireplace
Remote
Wall Plug x 6
Screw x 6
Washer x 6
Pebbles 0.9Kg
Crystals 0.5Kg
Logs x 4
Upper Wall Bracket
Please Note: Some parts are packaged within the cavity of the surround on the rear of the fire.
(For AGL035/AGL036/AGL056/AGL057)

7
PRODUCT DIAGRAMS

8
INSTALLATION INSTRUCTIONS
(For AGL035/ AGL037/AGL053/AGL054/AGL055)
This product is designed to be mounted flat to the wall. Before installation please
ensure that the floor and wall are flat, and there is nothing that would prevent the fire
fitting flush.
1. The fire is designed to be permanently
fixed to a wall with a minimum distance
of 300mm between the base of the fire
and the floor. A distance of 600mm is
recommended for the optimum height
on the wall.
2. The upper bracket should be placed
against the wall 490mm above the
planned position of the base of the fire.
3. While ensuring that the bracket is level
(using a spirit level) mark the position of
the six screw holes in the wall.
4. Put the bracket to one side, drill the
holes marked in step 3 with an 8mm
drill bit to a depth of around 35mm.
5. Clean any dust and debris from drilling,
and insert a wall plug into each hole,
ensuring they are flush with the surface
of the wall.
6. Hold the bracket in position and attach
to the wall using 6 screws.
7. Two people should carefully lift the fire into position, ensuring the top edge of the
fire engages with the bracket.
8. Spread the supplied pebbles / branches (model dependant) in position on the light
at the front of the unit.
NOTES:
•The wall plugs supplied are designed for solid walls, and so depending on the
type of wall, a different type of plug may be required.
•Before drilling into the wall, you must ensure that there is no pipework or wiring
behind the wall which may be damaged during installation.
•The fire must be installed by a competent person, if in any doubt about
installation, the suitability of the wall, or wall plugs supplied, professional advice
should be sought.

9
STEPS TO REPLACE DECORATION (FOR AGL035/AGL036/AGL037)
1. Remove the two screws with a phillips screwdriver
2. Take off the glass, the put decoration well (small pebble/crystal/log set supplied)
3. Install the glass carefully.
INSTALLATION INSTRUCTIONS
(For AGL035/AGL036/AGL056/AGL057)
IMPORTANT! Two people are
needed for wall installation.
1. Fix the Brackets with STD*14 screws
on the top left and right sides on back
of the unit.
2. Using a tape measure, measure the
distance between the two brackets.
Place the tape measure against the
wall and mark on where the two
brackets will be located using a
pencil. Then using an M8 drill bit, drill
holes on the wall and insert the wall
plugs.
3. Then use ST5*35 screws to fix the
product through Brackets.
Two holes are provided for
the screws for extra security.

10
OPERATION
ON/OFF
Press the power button to turn the unit On or Off.
In standby mode, press and hold the power button for 3
seconds to set the wireless network (see Wi-Fi
connection).
Press and hold the power button for 5 seconds in standby
mode to toggle between Celsius and Fahrenheit.
FLAME CONTROL
Press the flame button rapidly to adjust the flame
brightness. There are 5 levels with 5 being the brightest
and one the dimmest.
Press and hold the flame button for 5 seconds to enter the
flame colour settings. You can choose between the
colours
C1 Warm white + Red + Blue.
C2 Warm white + Red
C3 Red + Blue
C4 Warm white + Blue
C5 Blue
C6 Red
C7 Warm white
HEAT
CONTROLLER
Press the heat button repeatedly to change the heat level.
The heat level is indicated on the display by a bar. A small
bar means the heat is LOW a large bar means the heat is
HIGH. Press and hold the heat button to set the
temperature between 18 and 35⁰C.
TIMER
You can set 0-9 hours in 1-hour increments. As soon as
the time you set has elapsed, the fire will automatically go
out. To adjust the you hear a beep and ”F1”is displayed
on the screen. Then press the timer button repeatedly to
select one of the colours. Once you reach ”F9”,the setting
mode is exited and the colour selection start again.

11
REMOTE CONTROL
DISPLAY
Power
Button
Press to turn the appliance On and Off.
Flame Button
To adjust the flame brightness: Press this
button once and then adjust the flame
brightness using the arrow buttons. To
adjust the flame colour, press the flame
button twice, then use the Arrow buttons
to switch between flame colours (C1-C7).
Arrow Buttons
Press these buttons to select between
the different heating levels. The level you
select is shown on the heat indicator.
When the small bar lights up, a low
heating level is set. When both bars are
lit, a high heating level is set.
Temperature
Button
Press this button once and use the arrow
buttons to select the desired temperature
(18-35℃).
Timer On / Off
While the unit is on, press this button to
set the time until it switches off
automatically. You can set 0-9 hours in 1-
hour increments. As soon as the time you
set has elapsed, the fire will automatically
go out. To adjust the you hear a beep
and ”F1”is displayed on the screen. Then
press the timer button repeatedly to
select one of the colours. Once you
reach”F9”,the setting mode is exited and
the colour selection start again.

12
APP CONNECTION
NOTE: Some images may differ from the current app due to continuous product improvement.
2. Read the Privacy policy and
press the Agree Button.
3. Enter your email address or
phone number and press
continue to register.
4. A verification code will be
sent by the method selected
in step 3. Enter the code into
the app.
2. The app is now registered.
It will automatically log you
in following registration.
5. Type in the password you
would like to create. This
needs to be 6-20 characters,
with letters and numbers.
1. Press on the register button
at the bottom of the screen.

13
SETTING UP YOUR HOME WITHIN THE APP
TUYA is designed so it can work with a large number of compatible smart devices within
your home. It can also be set up to work with multiple devices within different houses as
such during the setup process, the app requires that different areas are created and
named to allow easy management of all your devices. When new devices are added,
they are assigned to one of the rooms you have created.
CREATING ROOMS
1. Press on the ADD HOME
button.
3. Type in a name for your
home,
4. Press on the location button
to select the location of your
home. (See SETTING
YOUR LOCATION below)
5. New rooms can be added
by pressing the ADD
ANOTHER ROOM option at
the bottom. (See ADD
ANOTHER ROOM below)
6. Untick any rooms that are
not required on the app.
7. Press DONE in the top right
corner.
SETTING YOUR LOCATION
Use your finger to
move the orange
HOME symbol.
When the symbol
is in the
approximate
location of your
home, press the
confirm button in
the top right corner.
Location details
allows the app to
be set up later to
respond to weather
conditions in your
area.
ADD ANOTHER ROOM
Type in the
name of the
room, and
press Done in
the top right
corner

14
CONNECTING USING THE QUICK CONNECTION METHOD
Before initiating the connection, make sure the WiFi indicator is flashing twice per
second. If not follow the instructions for changing the connection mode. Also ensure
your phone is connected to the WiFi network. (We advise turning mobile data off during
setup)
2. Select the type of device
as “Heater” within the Home
Appliance tab.
3. Press on the orange button at
the bottom of the screen.
4. Enter your Wi-Fi password
and press confirm.
5. This will then transfer the
settings to the heater. Wait for
this to complete. If this fails,
retry.
1. Open app and press “+” to
add device, or use the add
device button

15
CONNECTING USING AP MODE (ALTERNATIVE METHOD)
Before initiating the connection, make sure the unit is in standby mode, with the WiFi
Indicator flashing once per second. If not follow the instructions for changing the WiFi
connection mode. Also ensure your phone is connected to the WiFi network. (We
advise turning mobile data off during setup)
1. Open app and press “+” to
add device, or use the add
device button
2. Select the type of device
as “Heater” within the Home
Appliance tab.
3. Press on the AP mode
button in the top right of the
screen.
4. Ensure the WiFi indicator on
the heater is slowly flashing
(once per second), then
press on the orange button
at the bottom of the screen
to confirm
5. Enter your WiFi password
and press confirm.
6. Go to network settings in your
phone and connect to the
“SmartLife xxx” connection.
There is no password to
enter. Then return back to the
app to complete setup.
This will then transfer the settings to the heater.
Once the connection process has completed, go back to the network settings on your phone to ensure
your phone has reconnected to your WiFi router.

16
CONTROLLING YOUR APPLIANCE THROUGH THE APP
THE HOME SCREEN
NOTE: Due to continuous development of the app, the layout and available features may be subject to change.
Each device has its own entry on the home screen to allow the user to either quickly turn the unit on or off,
or to enter the device screen to make other changes.
Smart Scene: Allows you
to program intelligent
behaviour based on the
internal and external
environment
Add Device: Add a device
to the app, and go through
the setup process.
Profile: Provides the
option for changing
settings,
Name of Heater: Press to
enter the Device Screen
Home: Return to home
screen from the Smart
Scene and Profile screens
Voice Control: Press to
give verbal instructions for
operation.

17
DEVICE SCREEN
The device screen is the main control screen for the heater, providing access to the controls to amend the
functions and settings.
Edit Name: Use to
change the name of the
heater. Device information
and third part control can
also be assessed from this
menu.
Back: Returns to the
Home Screen
Power: Use to turn
the unit on or off.
Device Name
Desired
Temperature:
Displays what has
been set as the
target room
temperature.
Decrease Desired
Temperature
Temperature range
18-35⁰C
Increase Desired
Temperature
Temperature range
18-35⁰C
Current
Temperature:
Displays what the
current temperature
is.
Flame colour: Use
to change the flame
colour between C1
and C7.
Countdown Timer:
Use to set the
countdown timer
between 1 and 9
hours.
Heating: Use to turn
the heating
OFF/ON/LOW/HIGH.
Settings: Enter the
settings menu. You
can access
temperature scale
flame brightness
downlights colour
and the timer
schedule.

18
PROFILE TAB
The profile tab gives you the option to edit both your
detail, and use the added features of the unit.
HOME MANAGEMENT
Home Management proves options for managing
your TUYA account, giving options such as adding
a home, adding and removing rooms, and sharing
devices with family.
MESSAGE CENTRE
View notifications from devices, if alarms are set up
(dependent on device)
HELP CENTRE
Provides assistance using the features provided
within the app
MORE SERVICES
This allows the unit to be integrated with your
favorite home automation hardware such as Google
Home and the Amazon Echo.
FAQ AND FEEDBACK
Access frequently asked questions and
troubleshoot issues.
CONNECTION TROUBLESHOOTING
1. Check whether the device is powered on and is in the correctWiFi connection mode,
if not please refer to the CHANGING BETWEEN CONNECTION MODES section.
2. Ensure the WiFi password has been entered into the app correctly (Case sensitive)
3. Check that the phone is connected to the WiFi you are connecting the device to.
4. Ensure the network you are connecting it to is 2.4Ghz (5Ghz WiFi networks are not
supported), and that there is a strong WiFi signal to the item.
5. If your router is dual band, ensure that the 2.4ghz network has a different network
name (SSID). Further advice on changing router settings will be available from your
Internet service provider / Router manufacturer.
6. Check the settings on the router. Encryption should beWPA2-PSK and authorisation
type should be set to AES
7. Try using the alternative connection method. i.e. If connection is failing when
attempting to connect through CF mode, try AP mode.

19
CARE AND MAINTENANCE
Before cleaning the appliance, the power supply should be disconnected and the unit
should be allowed to cool.
Dust can be removed by lightly wiping the glass surface with clean, lint free cloth
or paper towel. To remove fingerprints or other marks, use a damp cloth with a
good quality household glass cleaner. The front glass panel should be completely
dried before reusing the heater.
CAUTION:
•Do not use abrasive cleaner on glass panel.
•Do not spray liquids directly onto any surface of the unit.
•Do not clean the glass on the inside of the unit as this may cause damage to the
surface
REPLACING THE BATTERIES
The remote control takes a
CR2025 battery. If the remote
becomes unresponsive,
please change the battery
with a new battery, as shown
in the image.
TECHNICAL SPECIFICATION
Description of
Product
Electric Wall Hanging Fire
Rated Voltage
220-240V ~
Rated Frequency
50/60 Hz
Rated Power
Max 2000W
Model
AGL035
AGL036
AGL037
AGL053
Dimensions
(mm)
1210 (W)
660 (H)
230 (D)
1210 (W)
630 (H)
230 (D)
1300 (W)
590 (H)
230 (D)
1205 (W)
589 (H)
250 (D)
Net Weight
28Kg
25Kg
30.8Kg
22.5Kg
Model
AGL054
AGL055
AGL056
AGL057
Dimensions
(mm)
1205 (W)
589 (H)
250 (D)
1205 (W)
589 (H)
250 (D)
1570 (W)
850 (H)
230 (D)
1205 (W)
1080 (H)
250 (D)
Net Weight
22.5Kg
24.7Kg
36.3Kg
36.1Kg

20
TROUBLESHOOTING
Most problems are simple to resolve - please refer to the following table before
calling a service engineer:
Problem
Possible Cause
Check
Fire has stopped
working
The fire has overheated and the
thermal safety device has
activated or a circuit breaker
has tripped.
Check there is power to
the socket where the fire
is connected, check the
fuse in the plug, check the
main power switch on the
unit is turned on and
leave for 10 minutes in
case of thermal cut-out.
Flame is not moving
Flame motor defective
Contact the retailer or
manufacturer.
SERVICING
It is hazardous for anyone, other than a qualified service technician, to carry out any
service or repair operation, which involves removal of any components. The lighting
for the flame effect is by LED bulbs which are designed to last for the life of the product and
are not user replaceable.
WASTE ELECTRICAL RECYCLING
Disposal: Do not dispose this product as unsorted municipal waste. Collection of such
waste must be handled separately as special treatment is necessary.
Recycling facilities are now available for all customers at which you can
deposit your old electrical products. Customers will be able to take any old
electrical equipment to participating civic amenity sites run by their local
councils. Please remember that this equipment will be further handled
during the recycling process, so please be considerate when depositing
your equipment. Please contact the local council for details of your local
household waste recycling centres.