Furnware Storg Elska Magic Corner ST22MCU.450L.CPWH User manual

A
Min. 580
C
B
16-20
500
450
Storg Elska Magic Corner
ST22MCU.450L.CPWH
ST22MCU.450R.CPWH
Do not use powered screw drivers for adjustment.
FITTINGS
27 of 4x16 Self-tapping screws
COMPONENTS
A. Rear frame
B. Lateral bracket
C. Side frame
D. Lower bushing
E. Upper bushing
F. Stop bracket
H. Door bracket
I. Centre pivot
L. Post-connectors
M. Linking arm
N. Cover caps
O. Marking template
P. Basket hooks (inside basket box)
MAINTENANCE
Clean with a soft, dry cloth. Avoid using solvents or abrasive.
TOOLS
A
E
F
B
D
P
O N
H M
L
Ensure cabinet base is
adequately supported!
I
C
Door A B C
450 Min. 410 Min.860/Max. 1010 500

1
Dimensions and diagrams show installation for right hand unit.
For left hand installation, dimensions are opposite.
Pre-drill cabinet following
the dimensions shown or
use the marking template
to mark screw positions.
10
79
138
202
266
330
394
513
53,50
26
52,50
12,50
317
273
D
32
443
730
E
E
C
G
57
4,50
49,50
489
505
491
491
272227.5
92

2
3
Attach the bottom track of the rear frame (A) to the positions given (fig 1).
Mount the upper part of the rear frame (A) to the bottom track (fig 2)
Extend the arms and fix in place (fig 3).
Tighten the grub screws to lock the arms (fig 4).
Remove transport tabs and discard (fig 5)
Mount the lateral bracket (B) and the stop bracket (F) into the
positions shown by following the dimensions or marking the
positions using the marking template (O).
6 of 4x16 Self-tapping screws
9 of 4x16 Self-tapping screws
FIG 1 FIG 2 FIG 3
FIG 4 FIG 5
53,50
26
52,50
12,50
513
10
79
138
266
394
202
330

4
5
Push the lower bushing (D) into the hole in
the stop bracket (F) as shown.
Fit the top pins of the side frame (C) into position in the lateral bracket (B) as shown (fig 1)
Lower the bottom pin of the frame into the bush in the stop bracket (F) (Fig 3)
6Fit the upper bushing (E) and turn until the
tab locks into place.
FIG 1
FIG 2 FIG 3
3
2
1

7
8
Slide the plain end of the centre pivot (I) into
the guide at the bottom of the side frame (C)
and fix in the position previously marked.
Using the post connectors (L) clip the linking
arm (M) into the centre pivot (I) and the 4th
or 5th hole of the rear frame (A) as shown.
9Mark out the door using the marking
template (O) or by following the dimensions
shown and attach the door brackets (H)
295
1 2 3 4 5
8 of 4x16 Self-tapping screws
Y
Y
18
135 291
375
375

10
11
Mount the door brackets (H) onto the side
frame (C) and tighten the locking screws.
Loosen locking screws to make adjustments
as shown.
12 Tighten locking screws after adjustments are complete.

13
14
Use the set screw in the stop bracket (F) to
adjust the opening angle.
Install the cover caps (N) as shown.

15 Insert the basket hooks (P) into the frames
(A, C) and install the baskets,