Furuno TZT2BB User manual

11/09/2023
Furuno USA, Inc.
TZT2BB Brilliance Control of MU Touch Monitor
1. Instruction
1.1. About the Feature........................................................................................................... 1
1.2. Connection..................................................................................................................... 2
1.3. Initial Setup .................................................................................................................... 3
2. Troubleshoot
2.1. Make sure proper IP address is selected on TZT2BB...................................................... 5
2.2. Cycle all System Power including the Power Source of HUBs. ........................................ 5

11/09/2023
Furuno USA, Inc.
1
1. INSTRUCTION
1.1. About this Feature
The Monitor Brilliance will be controlled with the brilliance bar on the TZT2BB via Ethernet.
It can be adjusted by repeatedly pressing the power key or dragging the brilliance bar icon
in the quick access menu. Centralized control of the brilliance for all NAVnet TZtouch2,
TZtouch3 and MU Touch Monitors connected to a TZT2BB can be achieved when activating
the Brilliance Synchronization feature between MFDs. TZT2BB software must be V7 or later.
TZT2BB TZT2 TZT2
Switching HUB
Hatteland Monitor Hatteland Monitor
USB cable
HDMI cable
Ethernet cable
Brilliance Control by TZT2BB
Brilliance Synchronization between NAVnet TZtouch2/ TZtouch3

11/09/2023
Furuno USA, Inc.
2
1.2. Connection
The TZT2BB can connect to MU touch Monitors using Ethernet. This can be done by directly
connecting to the TZT2BB internal Hub or through a HUB101 or similar switch.
MPU-004
HDMI1 HDMI2
USB cable for primally monitor (1) USB cable secondally monitor (2)
PSD003
Ethernet Ethernet
Hatteland Monitor Hatteland Monitor

11/09/2023
Furuno USA, Inc.
3
1.3. Initial Setup
1.3.1. Set a static IP address to the MU Touch Monitors
1) Open “Menu” by pressing the Menu button on the monitor.
2) Go down to “Management Settings” by using Navigation buttons, then touch the Menu
button to enter.
3) Select “Communication” and change the setting to “IP address, Fixed IP”.
4) Change the IP address to one of the IP addresses compatible with the TZT2BB.
(IP address Range: 172.31.26.190 – 199)
5) Repeat the same process at the secondary monitor but you must use a different IP
address from primary monitor, continue as needed for additional TZT2BBs with MU
touch monitors.
6) Cycle the power of monitor(s) by shutting off the breaker or unplug the power cable
for monitor(s) to apply the change, then plug back in.
7) Cycle the power of network Switching HUB. If Monitor(s) connect to TZT2BB internal
HUB, Cycle the power of TZT2BB.

11/09/2023
Furuno USA, Inc.
4
1.3.2. Select proper IP address of “Set External Monitor IP Address” on TZT2BB.
1) Open “Set Ext. Monitor IP address” found under Initial Setup
2) Select the proper IP address on TZT2BB to match the one that was assigned to the
monitor.
3) Repeat the same process at additional monitors, as needed.
4) Brilliance Control will then be available. The brilliance can be adjusted by tapping the
power key or dragging the brilliance bar icon in the quick access menu.

11/09/2023
Furuno USA, Inc.
5
2. TROUBLESHOOT
2.1. Make sure proper IP address is selected on TZT2BB.
The IP address of the setting on the TZT2BB must be same as the connected monitor’s IP
address.
2.2. Cycle all System Power including that for any network HUBs.
Brilliance control uses TCP/IP Communications, so the ARP table which caches the physical
address (MAC address) of each device and its IP address should have the latest information.
The table is disposed and refreshed automatically, but it is executed after elapsing certain
times per devices or when the power is cycled, so if the Brilliance Control feature does not
work, all devices including switching HUBs need to be power cycled to make sure that the
ARP table gets the latest information.
Here is a sample video on how this works.