Furuno FM-8800D User manual

VHF RADIOTELEPHONE
FM-8800D/8800S
FM-8800S/D INTL Ver.
FM-8800: 0550215-02.xx/03.xx
HS-8800: 0550216-01.xx
FM-8800S Russian Ver.
FM-8800: 0550220-01.xx
HS-8800: 0550221-01.xx

The paper used in this manual
is elemental chlorine free.
・FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
Telephone : [phone]
Fax : [phone]
A : JUL 2005
.
Printed in Japan
All rights reserved.
C : AUG . 18, 2010
Pub. No. SME-56420-C
*
00015637400
*
*
00015637400
*
(NAYO ) FM-8800D/S
*
00015637400
*
*
00015637400
*
* 0 0 0 1 5 6 3 7 4 0 0 *

Panel Speaker
X X X X X X X X X X
Panel Speaker
X X X X X X X X X X
RB-8810/HS-880 RB-8800/HS-880 Remote station-Other Handset ear speaker
Panel Speaker
X X X X X X X X X
Panel Speaker
X X X X X X X X X
RB-8810/HS-880 RB-8800/HS-880 Remote station-X Handset ear speaker
X
X
X
X
X
X
X
X
X
X
X
X
Panel Speaker
X X X X X X X X
FM-8800D/S Handset ear speaker
X X X X X X X X
Remote Station-X Handset Off-hook On-hook Off-hook On-hook Off-hook On-hook Off-hook On-hook Off-hook On-hook Off-hook On-hook Off-hook On-hook Off-hook On-hook
On-hook/off-hook Status Main Handset Off-hook On-hook Off-hook On-hook Off-hook On-hook Off-hook On-hook
OFFHOOK SPKR OFF ON OFF ON
Volume Menu Setting Monitor Domain XXXX Private Public
The table lists the active speakers according to Volume menu settings and on-hook/off-hook status of the handsets. Regular (DSC Individual call, other than PSTN) call and PSTN call are set though the individual menu. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

(Addenda No.9 of this page is missing.)

Procedure: DSC Test between No. 1 and No. 2 FM-8800S/Ds
1) On No. 1 FM-8800S/D, press [CALL] key to create DSC message.
- CALL TYPE: Test
- SHIP ID: MMSI of No. 2 VHF Own ship
2) Press and hold down [CALL] key more than 3 seconds to transmit DSC message on
No. 1 FM-8800S/D. “Call in progress on CH70” message appears and immediately
“Test request call received” message appears. And then alarm is output.
Press [CANCEL] key and stop the alarm.
Note: This is a “loop-back” test where the transmitted signal is received from CH70
WR and this RX message appears on the window.
2/5
When TEST ACK is transmitted from own
ship, “TEST ACK” log is not recorded in
“RCVED ORDINARY” window.
Fig. 1 Communication Test
Check LOG
Dotted line shows DSC TEST
CALL is received by CH70 WR.

3) On No. 2 FM-8800S/D, TEST message is received from No. 1 FM-8800S/D. “Test
request call received” message appears and alarm is released.
Press [CANCEL] key and stop the alarm.
4) Press [ENT] key on No. 2 FM-8800S/D. Then “Received Message” window is
changed to “Send Message” one.
Press and hold down [CALL] key more than 3 seconds to transmit TEST ACK
message.
After the transmission, the “CH16” window is displayed.
5) No. 1 FM-8800S/D receives “TEST ACK” message from No. 2 FM-8800S/D. And
then “Test acknowledge received” message appears and alarm is released.
Press [CANCEL] key and stop the alarm.
6) On No. 1 FM-8800S/D, check the “TEST ACK” message received from No. 2
FM-8800S/D.
7) On No. 1 FM-8800S/D, open “RCVD ORDINARY” LOG and check an unread icon
“TEST CALL” and a LOG of “TEST ACK”.
8) DSC Test from No. 2 FM-8800S/D to No. 1 FM-8800S/D is made in accordance with
the above procedure.
3/5

DSC Test by only one FM-8800S/D
Note: When RT ANT is used together with CH70 WR ANT, TX radio wave is transmitted to
RX Circuit of CH70 WR. So, function test for DSC and CH70 WR can be carried out.
Procedure:
1) Select [SHIFT] -> [5: ACK] and set to “MANUAL ACK”.
2) If possible, select [MENU] -> ERASE LOG and delete a LOG of “RCVED
ORDINARY”.
3) Select [MENU] -> [0: HI/LO] and set a power to “LOW”.
1) Press [CALL] key to create DSC message.
- CALL TYPE: Test
- SHIP ID: MMSI of No. 2 VHF Own ship
2) Press and hold down [CALL] key more than 3 seconds to transmit DSC message.
“Call in progress on CH70” message appears and immediately “Test request call
received” message appears. And then alarm is released. Press [CANCEL] key and
stop the alarm.
4/5
Fig. 2 Communication Test by only one VHF
Check LOG
Dotted line shows DSC TEST
CALL is received by CH70 WR.

3) Press [ENT] key. Then “Received Message” window is changed to “Send Message”.
Press and hold down [CALL] key more than 3 seconds to transmit TEST ACK
message.
After the transmission, the “CH16” window is displayed.
4) Open “RCVD ORDINARY” LOG window and check a LOG of “TEST CALL”.
5/5

Changes in FM-8800D/S system
1. Software update history
No. 6 and 7 units in below table are manufactured in October 2009.
No. Unit INTL or
Russian Ext. ALM output Software Ver. CPU Board
Ｖｅｒ． ITU-R No. Type
approval RTC kit
1
FM-8800
S/D
INTL Normal Open 0550215-03.06 05P0773 M.493-10 MED not
equipped
2 Russia Normal Open 0550220-01.03 05P0773A M.493-11 Russian equipped
3 INTL Normal Close 0550215-03.06 05P0773B M.493-10 MED not
equipped
4 Russia Normal Close 0550220-01.03 05P0773C M.493-11 Russian equipped
5 INTL Normal Open 0550215-04.01 05P0773D M.493-11 MED equipped
6 INTL Normal Close 0550215-04.01 05P0773E M.493-11 MED equipped
7 HS-8800 INTL 0550216-01.03 05P0781 M.493-11 MED
8 Russia 0550211-01.02 05P0781A M.493-11 Russian
Note: Alarm output of CPU Board, “Normal Open” or “Normal “Close” can be selected.
On all boards, the program can be updated to be compliant with Recommendation
ITU-R M.493-11.
2. DMC-5, not connectable
When the program of software is updated to 04.01/01.03, DMC-5 is not connectable. So,
install IC-350 in place of DMC-5.
3. AUTO REVERT function
“AUTO REVERT” function is selected from User menu. Remote Handset has the same
function.
4. Contrast adjustment
Contrast is adjusted in “CONTRAST” menu. To reset it to the default setting, press and
hold down [SHIFT] key.
5. Position Data
The data of own ship’s position is displayed in 1/10000 min. and it is displayed on
“Received Message” and “Send Message” windows.
2/6

6. Distress relay
When the same distress relay message is received more than twice within one hour, the
alarm is not activated.
7. Compose Message
The indication on “Compose Message” window is
changed from “TCmd1” and “TCmd2” to “KAIND”,
“COMM MODE” and “COMM MODE”.
On the last line, a message is displayed whether
transmitted message is requested ACK or not. “ACK
REQ” message is displayed for Call and Distress alert
and “NO ACK REQ” is displayed for all Call and Group
call. “Polling Call” and “AREA CALL” are deleted from
this window.
8. Transceiver unit and Remote Handset Operation Panel
The indications of “AUTO CH” setting and “DATA/TIME” from RTC are added on the
operational panel.
Position data is displayed in 1/10 000 min.
FM-8800S/D Operation Panel Remote Handset Operation Panel
- AUTO CH: ENB/DIS (Set in [MENU] -> AUTO CH)
The state of AUTO ACK is set to ON and ON-HOOK.
When receiving the INDVIDUAL/ROUTINE call, communication CH is changed
automatically after transmitting AUTO ACK.
When CH is set to “ENA”, it changes automatically. And when set to “DIS”, it changes
manually.
- Year/Day/Time
Year/Month/Date/Time data using for LOG of Time stamp are displayed.
Data priority is displayed in ZDA > RMC > manual. When it is set by manual, set data in
[MENU] -> RTC.
3/6