Fusion 29002 User manual

Part Description
ALight Head
BConnection Tube
CGround Stake
DWire
EConnector
B
A
CD
E
LOW VOLTAGE
FLOOD/PATHWAY LIGHT
model no. 29002
Read all instructions before assembly. Failure to do so may result in incorrect
assembly or possible injury.

Assembly
• Note: Some components may come
preassembled.
• Insert the Connection Tube (Part B) onto the
adapter at the base of the Light Head (Part A),
pressing together until secure.
• Assemble the Connection Tube (Part B) to the
Ground Stake (Part C) by turning in a clockwise
direction until secure.
Important Safety Information
Please read and understand all instructions before attempting to assemble, operate, or install this
product. Keep this manual for future reference.
WARNING:
• Risk of fire or electrical shock. Turn off power before assembly.
• Do not install or connect wires with wet hands.
• Do not install this product within 10 feet (3.05 meters) of a pool, spa, fountain, or other water source.
• The main cable is intended for shallow burial - maximum depth must not exceed 6 inches (15.24 cm).
• For low voltage landscape lighting systems only.
• Do not step on, or drive over the main cable.
CAUTION:
• This lighting fixture is only suitable for 12V power supply.
• This LED lamp is a highly efficient, extremely low wattage, energy saving product. Recommended not to
exceed 80% of the total rated watts of the transformer.
• Use shielded cable for outdoor use in the following sizes: SPT-2W 18G, SPT-2W 16G, SPT-2W 14G, SPT-
2W 12G.
• Do not attempt to service, adjust, or replace any part of the LED light source.
• Do not repair or modify this product in any way.
• Do not submerge in water.
Getting Started
Please do not throw away any packing material until all parts are verified as present.
B
A
C D
E
1
2
1
2

Running the Landscape Wire (Not Included)
RUNNING THE LANDSCAPE WIRE:
• The included cable connectors are to be used only on low voltage power cable with SPT-2W or
equivalent 18, 16, 14, or 12 AWG cable.
• Do not use landscape cable smaller than listed in the chart below.
• The landscape wire should run from the power pack to each light fixture without being cut.
• Do not run the wire within 10 feet (3.05 meters) of a pool, spa, fountain, or other water source.
• The landscape wire should be protected by routing it close to the light fixture; near a building, deck,
fence, or other outdoor structure.
CONNECTING LIGHT FIXTURE TO LANDSCAPE
WIRE (Figures 1 & 2):
• The included cable connectors are to be used only on
low voltage power cable with SPT-2W or equivalent
18, 16, 14, or 12 AWG cable.
1. Open the Connector (Part E) that is attached to the
end of the Wire (Part D). See Figure
2. Align the landscape wire (not included) through the
Connector (Part E), allowing the contact pins (2) to
pierce the wire on both sides. Close the Connector
(Part E) to secure. See Figure
3. Determine the area where you would like to install the
light and insert the stake (Part C). Do not push the
fixture into the ground by the fixture head.
CAUTION: In clay or hard soil conditions, moisten the
ground with water before inserting the stake into
the ground to avoid any breakage.
ADJUSTING THE LIGHT FIXTURE:
• Before you bury the landscape cable underground, it
is recommended you adjust your light fixtures at night
to ensure you are happy with the position and lighting
effect.
BURY THE LANDSCAPE WIRE:
• The landscape wire can be buried under soil, grass,
or stone at a maximum depth of 6 inches (15.24 cm).
See Figure
Contact Pins
Power
Wires
Contact Pins
Power Wires
2
1
Power Pack Wattage Minimum Gauge Cable
240-300 12
120-240 14-12
60-120 16-14-12
0-60 18-16-14-12
DETERMINING LIGHT FIXTURE LOCATION:
• To achieve consistent brightness and longer light
fixture life, install the first light fixture at least 10 feet
(3.05 meters) from the power pack.
3
1
2
3
• CABLE SELECTION: Use the chart to determine
the MINIMUM gauge cable to be used, depending
on the wattage of the power pack. Using larger
cable will ensure maximum light output.

Troubleshooting
If only some of the lights work:
1. Check the contact pins of the connector to make sure they have pierced the landscape wire correctly.
2. The problem could be with the connector, or LED of the light fixture.
4
5
6
4
5
6
If the light does not work at all:
1. Make sure the switch and circuit breaker are on.
2. Make sure the wiring connection is correct.
3. Make sure the connections between the contact
pins of the connector and the landscape wire are
correct.
Should you need to re-connect the Wire (Part D)
to the Connector (Part E):
1. Push up the lever on each side of the Connector
(Part E) to open. See Figure
2. Feed one separated end of the Wire (Part D) into
one of the openings on the Connector (Part E), and
the other separated end of the wire into the other
opening, until each wire reaches the back of the
opening (about 3/4”). See Figure
3. Press both levers down to close. See Figure
Care and Maintenance
• Regulary clean the glass and coated metal surfaces with a non-abrasive cleaner.
• Do not use cleaners containing harsh chemicals, solvents or abrasives.
1-Year Limited Warranty
This product is covered under a one year limited warranty. Fusion Products Ltd. warrants to the original
purchaser that this product is free from defects in materials and workmanship for the period of one year
from date of purchase.
For Technical Support and/or Warranty inquiries please contact:
Fusion Products Ltd.
Monday to Friday
8:00-4:00 PM EST
5 Cherry Blossom Road, Unit 7
Cambridge, Ontario N3H 4R7
Tel: [phone] Fax: [phone]
Email: [email protected]
Website: www.fusionproducts.ca