Futek F9300 User manual
使 用 手 冊
FUTEK F9300 點矩陣式印表機
FUTEK F9300
I
Important Safety Instructions (English)
Read the following instructions thoroughly before starting up your printer.
•Never carry out maintenance or repair work yourself. Always contact a qualified service technician.
•Keep this Operator’s Manual in a place which is easily accessible at all times.
•Place the printer on a solid and even base so that it cannot fall.
•Never place the printer in the vicinity of inflammable gas or explosive substances.
•Ensure the printer is connected to a socket with the correct mains voltage.
•Always disconnect the printer from the mains before opening the device to perform maintenance work
or remedy errors.
•Do not expose the printer to high temperatures, direct sunlight or dust.
•Keep all liquids away from the printer.
•Protect the printer from shock, impact and vibration.
Make sure that the printer and computer are switched off before connecting the data cable.
•The print head will become very hot during printing; avoid contact with the print head after printing has
finished.
•Do not perform any operation or action in any way other than those provided in this manual. When in
doubt, contact your dealer or your customer support.
The device and mains-socket must all times be easily accessible.
FUTEK F9300
IV
TRADEMARK ACKNOWLEDGEMENTS
“IBM” is a trademark of International Business Machines Corporation.
“EPSON” is a trademark of Epson America Incorporated.
“DEC” is a trademark of Digital Equipment Corporation.
“Centronics” is a trademark of Centronics Data Computer Corporation.
“DOS” is a trademark of Microsoft Corporation.
“SAP” is a trademark of SAP AG.
“Windows”, “Windows 7”,”Windows 8”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows 2000”, “Windows
2003/2008/2013 Server”, “Windows XP” and “Windows Vista” are trademarks of Microsoft Corporation.
All other product names and company names appearing in this manual are the registered trademarks or
trademarks of the individual companies.
FUTEK F9300
1
TABLE OF CONTENTS
1 Printer at a glance ............................................................................................................................... 1
1.1 Unpacking the printer .................................................................................................................. 1
1.2 Remove transport locks............................................................................................................... 1
1.3 Prepare your printer..................................................................................................................... 2
1.4 Parts description.......................................................................................................................... 4
2 Installation ........................................................................................................................................... 5
2.1 Placing the printer........................................................................................................................ 5
2.2 Connecting the printer ................................................................................................................. 5
2.2.1 Parallel interface (IEEE 1284) ........................................................................................... 6
2.2.2 USB 2.0 (Full Speed)......................................................................................................... 6
2.2.3 Ethernet............................................................................................................................. 6
2.2.4 Serial Interface (RS-232C) as option................................................................................. 7
2.2.5 Connecting the power ....................................................................................................... 7
2.2.6 Switch on the printer.......................................................................................................... 7
2.3 Installing the ribbon cartridge ...................................................................................................... 8
3 Installing the paper ............................................................................................................................ 10
3.1 Adjusting the print gap for various form thicknesses ..................................................................10
3.2 Paper path introduction ..............................................................................................................11
3.2.1 Cut sheet paper handling (front friction only)....................................................................11
3.2.2 Fanfold paper handling.....................................................................................................12
3.2.3 Top-Of-Form adjustment ..................................................................................................16
4 Control Panel Operation......................................................................................................................... 17
4.1 Operation of the LCD Panel.............................................................................................................17
4.1.1 The LC display .................................................................................................................17
4.1.2 Online mode.....................................................................................................................18
4.1.3 Offline mode .....................................................................................................................18
4.1.4 Setup mode......................................................................................................................19
4.2.5 Power on functions...........................................................................................................19
5 Setting parameters for the printer ............................................................................................................ 20
5.1 Setting the parameters through the LCD Panel ..........................................................................20
5.1.1 Enabling access to menu mode .......................................................................................20
5.1.3 Menu configurations .........................................................................................................21
5.1.4 Menu handling..................................................................................................................23
5.1.5 Selecting the LCD display language.................................................................................24
5.2 Menu structure ...........................................................................................................................25
5.3 Full list parameters setting..........................................................................................................26
5.3.1 Menu Configuration list.....................................................................................................26
5.3.2 Advanced Menu ...............................................................................................................33
5.4 Display messages ......................................................................................................................36
5.4.1 Messages LCD Panel.......................................................................................................36
Symbols used Important information is highlighted in this manual by two
symbols.
CAUTION highlights information which must be observed in
order to prevent injuries to user and damage to the printer.
NOTE highlights general or additional information about a
specific topic.
FUTEK F9300
1
1 Printer at a glance
1.1 Unpacking the printer
Besides this manual, the package will contain: a power cord, a ribbon cartridge, a tractor, a CD
and 6 pieces of U-wire paper support.
1.2 Remove transport locks
FUTEK F9300
2
1.3 Prepare your printer
Front View
Rear View
FUTEK F9300
3
For Fanfold
For Cut Sheets
FUTEK F9300
4
1.4 Parts description
1Control PanelLCD: A LCD display and two keys indicates the operating
status and allows simple settings of the printer.
2LatchSliding it down unfolds the cut sheet support.
3Front CoverUnlocking the front cover unfolds the cut sheets support.
4Power SwitchTurns on and off the printer.
5Hand WheelTurn the knob to load or clear the paper. It should be
inserted the full way until you can hears some sort of
“Click”.
6Paper SupportAt slanted position, it stacks cut sheets; at flat position, it
separates fanfold printouts from incoming forms.
7Top Covers 1&2Protect the internal parts and reduce the noise.
8Head Gap Lever Adjusts the gap between the print head and various
form thickness.
9Paper Path Lever Selects various paper sources.
10Upper Friction Guides the form when cut sheets or fanfold forms are used.
11Power Socket A power cord is plugged into the socket to supply the
power.
12Interfaces The interface cable of the host computer is plugged into
one of the interfaces.
13Mute Cover Latch You must open it before you open the top cover 1.
14Print Head Utilizes 24 needles to strike on ink ribbon and paper.
15Ribbon Cartridge Holds the ink ribbon fabric.
16Tractors Holds and transports fanfold forms.
17Paper Guides
Left/Right
Sliding the guides varies the form width and the left
margin on a cut sheet.
18Cut Sheet Support A flat surface supports a sheet or multi-part form.
FUTEK F9300
5
2 Installation
2.1 Placing the printer
Place the printer on a solid, flat, stable surface such that the printer sits firmly and cannot
move. Select an environment with sufficient ventilation, easy access to the control panel and
paper input areas as well as the printed output.
When selecting the printer location, observe the following additional requirements:
1) Never place the printer near to any flammable gas or explosive
substances.
2)Do not expose the printer to direct sunlight. If you cannot avoid
placing the printer near a window, protect it from the sunlight with a
curtain.
3) When connecting a computer to the printer, make sure the maximum
recommended cable length is not exceeded.
4) Ensure sufficient distance between the printer and any heating
devices/radiators.
5) Avoid exposing the printer to extreme temperature or air humidity
fluctuations. Above all, avoid dusty environments.
2.2 Connecting the printer
This printer is configured with a Parallel, USB and Ethernet interface as standard. An optional
Serial interface can be installed additionally.
FUTEK F9300
6
2.2.1 Parallel interface (IEEE 1284)
Make sure that the printer and the computer are switched off and connect the parallel cable
between the printer and the computer. Lock the connector with the 2 clips on the printer
interface connector; tighten up the 2 screws on the other end connecting to the computer.
2.2.2 USB 2.0 (Full Speed)
Plug in the USB cable to the printer and the computer.
2.2.3 Ethernet
FUTEK F9300
7
2.2.4 Serial Interface (RS-232C) as option
2.2.5 Connecting the power
Plug in the power cord to the printer power socket as shown in the diagram.
Connect the printer to the correct voltage power source.
The socket-outlet shall be installed near the equipment and shall
be easily accessible.
2.2.6 Switch on the printer
Switch on the printer as shown in the diagram.
FUTEK F9300
8
2.3 Installing the ribbon cartridge
1) Switch off the power.
2) Unfold the top cover and follow the steps 1.2.3.4 in the below picture.
3) Flip the upper friction assembly
FUTEK F9300
9
4) Insert the ribbon cartridge till it is tightly locked in position.
5) Insert the ribbon fabric in between the print head and ribbon mask.
6) Turn the knob on the left hand side several times in order to tighten the fabric, and the
fabric will slide downwards into the correct position between printhead and ribbon mask
after the moving.
7) Restore the upper friction assembly to its original position.
Print head may be hot, please move the printhead by moving the carriage.
FUTEK F9300
10
3 Installing the paper
The printer can handle either single sheets or continuous forms. The printer is able to print up
to 5 copies (original plus 5).
To ensure the print quality and protect the print head, set a proper print gap by the
gap lever (see 3.1) for the form thickness and do not load folded, damaged,
wrinkled, or curled paper.
3.1 Adjusting the print gap for various form thicknesses
The print gap lever is on the left side of the printer inside the top cover.
Take care to adjust the print gap lever to a suitable position whenever you change the number
of copies being printed. Using the wrong print gap may cause print head damage or paper
jams.
The recommended gap lever position for different form thickness is:
Paper type Lever position
1-part 1
Original + 1 copy 2
Original + 2 copies 3
Original + 3 copies 4
Original + 4 copies 5
Original + 5 copies 6
The position “Ribbon” only is suitable for loading the ribbon. When the lever is set higher than
appropriate it will result in poor print. The ribbon and head life will be shortened.
FUTEK F9300
11
3.2 Paper path introduction
3.2.1 Cut sheet paper handling (front friction only)
1) Place the paper path lever to the cut sheet position.
2) Unlock the front cover with the latch to unfold the cut sheet support.
3) Adjust the gap lever if necessary; see 3.1.
4) It is recommended to align the left paper guide exactly to the mark > I <. This marks the left
edge of the stationery. Slide the right guide to the position of the right edge of the stationery.
5) Insert the stationery straightly all the way into the guided slot until it stops.
6) Press the load key to feed the paper to the correct print position, automatically. The
printer clears the Paper End condition and goes into the ready or online state.
FUTEK F9300
12
3.2.2 Fanfold paper handling
3.2.2.1 Front push tractors for fanfold
1) Close the front cover if previously opened. Switch the paper path lever to one of the
desired tractor positions.
2) Move the paper path lever to the desired position.
3) Adjust the head gap lever if necessary.
4) Open the front cover by tilting the cover from bottom to the top, and make sure it’s locked in
place (see below pictures).
Lock the front cover in the way that is shown in the pictures.
Make sure the front cover is locked.
FUTEK F9300
13
5) If you do not need to adjust the left margin go to the next step. Open the right and left
tractor flaps, insert fanfold paper into the left-hand tractor, and make sure that at least
three paper transport holes are positioned on the tractor pins, close the tractor flap,
open the latch lever and align the tractor so that the first printing position on the
paper matches the IIIIXIIII mark on the printer housing, then lock the lever again.
6) Align the right-hand tractor to the width of the paper and insert the paper (Make sure that it
is inserted by the same length as on the left-hand tractor in order to avoid any paper jam).
Then close the tractor flap and slide the tractor to the right until the paper is slightly
tensioned, then lock the tractor.
7) Lower the front cover, switch the printer on.
For LCD: The active paper source (TrFront) appears in the display, the paper will
automatically load when the printer is in online mode and receives data from the
computer. Also, you can press the load key (key 4) only to load paper before
starting the printout.
FUTEK F9300
14
3.2.2.2 Rear tractors for fanfold
FUTEK F9300
15
3.2.2.3 Top pull tractors for fanfold
For the steps ②and ③, please refer to the 2.3
FUTEK F9300
16
3.2.3 Top-Of-Form adjustment
For pull tractor (PullTr), follow the steps below to adjust the first print position:
1) Remove Paper from printer.
2) Power on the printer.
3) Lift the Top Cover so you can see the transparent ribbon guide in front of the
print head.
4) Install the paper into the pull tractor.
5) Move the paper with the hand wheel so the perforation of the fanfold paper
lies exactly at the top of the transparent ribbon guide.
6) Close the Top Cover.
7) Press the Load key on the panel.
8) The printer now moves the paper to the correct first print position on a page (TOF).
Table of contents
