FX LAB G017KC User manual

G017KC
4 Eect Disco Lighting Kit with Stand
2 x LED Par Light | 1 x LED Crystal Light
1 x LED Projection Light | 1x T Bar Lighting Stand kit
Instruction Manual

IMPORTANT
Installer and Users please note:
These instructions should be read carefully and left with the user of the product for future
reference.
BEFORE USE
You must inspect these products including their power supplies before use for any signs of
damage. If the products or their power supplies are damaged in anyway, DO NOT use it, and
contact your supplier immediately.
PRODUCT SAFETY
• These units can be used by children aged 8 years and above, and by persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision and instruction concerning the use of the appliance in a safe way and
understand the hazards involved.
• Children should be supervised to ensure that they do not play with the units.
• Only use on a at stable surface.
• Do not look directly into the beams.
• Do not leave these products connected to the mains when unattended.
• Disconnect the units from the mains when not in use.
• Do not move the unit whilst operating.
• For indoor use only.
• Do not use in bathrooms, or in wet or damp locations.
• Arrange the cables so that they do no cause a trip hazard.
• Not suitable for people with photo sensitive epilepsy or similar conditions.
GENERAL SAFETY REQUIREMENTS
Domestic wiring must be tested periodically by a qualied electrician at least once every 10 years
or at every change of occupancy.
For oce and retail premises, and buildings such as village halls, the wiring must be inspected at
least once every 5 years.
It is recommended that all building be tted with smoke alarms (it is mandatory for new buildings).
OPERATION
Assemble the stand and attach the lighting eects to the T-bar using the nuts and bolts provided.
Make sure the units are rmly attached to the bar and pointing in the general direction required.
Final adjustment can be made by adjusting the hanging brackets.
Plug the mains power supplies in to a wall socket and attach to each of the lighting eects via the
sockets on the rear of the units.
If an extension socket is to be used it must be fully unwound and placed so as not to cause a trip
hazard.
Par Lights:
This has a 3 position switch
Position 1: O
Position 2: Auto scrolling colour changing mode
Position 3: Sound to Light: The unit reacts to the ambient sound in the room.
Led Crystal Effect:
Rotary Switch Control
Fully anti-clockwise position: Turns the unit o
Turning the Switch Clockwise: Switches the unit on and acts as a speed control for the sound to
light function.

OPERATION (CONTINUED)
Led Projection Light:
Switch on via an On/o button on the rear of the product. The unit operates using a sound to light
function.
MAINTENANCE
Always disconnect the units from their power supply before cleaning
Clean the outside of the units with a soft damp cloth, with a drop of washing-up liquid. Dust can
be removed by using a small paint brush or similar.
FAULT-FINDING
Unit Does Not Function:
1) Check the power supplies are plugged into a wall socket and the socket is switched on.
2) Make sure the leads are plugged into the sockets on the back of the units and that all switch’s
are in the correct setting.
PAT TESTING
When used in a workplace, this product must be safety-tested yearly by a qualied electrician (PAT
Tested) in order to comply with the Electricity at Work Regulations.
If hired out, it must be PAT tested prior to each hire.
We recommend that it is PAT tested regularly when used in a domestic environment.
DISPOSAL AND RECYCLING
You must not dispose of this appliance with domestic household waste.
Most local authorities have specic collection system for appliances and disposal is free of charge
to the end-user.
When replacing an existing appliance with a similar new appliance your retailer may take the old
appliance for disposal.
PAT TESTING
When used in a workplace, this product must be safety-tested yearly by a qualied electrician (PAT
Tested) in order to comply with the Electricity at Work Regulations.
TECHNICAL SPECIFICATION
Weight: ....................................................................................................................................... 2 kg
Plug in Mains Power Supply: ..................................................................................4 @ 230V@50Hz
Product In-put Voltage .................................................................................................5V DC @ 6W
Stand Height Max................................................................................................................ 1440mm
Stand Height Min................................................................................................................... 900mm
Bar Length............................................................................................................................. 600mm

SERVICE WARRANTY
Electrovision guarantees the product free from defects in materials and workmanship for a period
of one year.
Should this unit be operated under conditions other than those recommended, at voltages other
than the voltage indicated on the unit, or any attempts made to service or modify the unit , then
the warranty will be rendered void.
The product you buy may sometimes dier slightly from illustrations. This warranty is in addition
to, and does not aect, your statutory rights.
If you have any problems with this product, please call our Help Desk on [phone]. The
help desk is open from 8 am until 1 pm.
Electrovision Ltd.,
Lancots Lane, Sutton,
St. Helens, Merseyside.
WA9 3EX
website: www.electrovision.co.uk