G4S SmartAlarm P5 User manual

Alarms and false alarms
The panel sends an alarm signal to the Monitoring Service. The Monitoring Service will
then respond as arranged with you. Typically, a guard will be dispatched to your home.
If you arrive at the panel when the alarm condition is active - with a sounding siren
(the siren falls silent after 3 min.) and the red LED flashes do the following:
!
1) Press the key to display the activated sensors.
2) Then enter your user code. Services are now turned off and a ‘clear’ message is
automatically sent to the Monitoring Service. The red LED will continue to flash until
the panel is reconnected, or if you browse through the event log.
If you want information about where in the house the alarm is enabled do the
following:
1) Enter followed by the code
2) Select the event log by pressing 6-1, use the and keys to view previous
events.
3) To finish viewing the event log press the key 3 times.
If you have caused an alarm by mistake, it must be reported to the Monitoring
Service. This must be done immediately after you have caused the alarm:
1) You can cancel a false alarm simply by entering your user code.
This stops the siren and sends a message to the Monitoring Service if the alarm is
turned off by an authorized user.
Control your alarm online
!
APP - for Smartphone
"mitG4S" allows you to control and monitor your G4S SmartAlarm P5 from your Wi-Fi or
3G Iphone, Smartphone or android.
With G4S's "mitG4S" you can arm and disarm your alarm, change contacts, etc.
The app is available for Android phones and tablets on the Android Market and the App
Store for iPhone and iPads.
Customer log in via www.G4S.dk
Useful phone numbers:
Monitoring Service:([phone]
Contact Center :([phone]
G4S Security Services A/S
Roskildevej 157
2620 Albertslund
Phone: [phone]
!
!
!
User!Manual!
SmartAlarm!–!P5!
!
! !

Congratulations on your new G4S SmartAlarm P5. In this folder you can find
information about the SmartAlarm, its capabilities and how you can use them.
To view the full version of the user manual, please see our website -
www.g4s.dk/vejledning - to find a printable PDF file.
The Front Panel
The SmartAlarm consists of one front panel, various sensors and a number of optional
units. The front panel is the brain of the system. It communicates with all the devices
connected to the system. For example, in the event of a burglary, a detector sends a
signal to the front panel indicating that it has sensed motion on the premises. On
receiving this signal, the front panel makes the decision to report the alarm to your
Monitoring Service and activate the siren
You can operate the alarm in several different ways. Apart from the keys on the front
panel the system can contain a number of peripheral devices, such as panels and
keyfobs. The panel keys on the SmartAlarm, includes all the features you need to control
the alarm.
LCD display System
status
indicators
Arming keys Menu
navigation
keys
Alphanumeric
keypad
Keyfobs
For SmartAlarm can be purchased keyfobs. The functions of the keyfob’s buttons are
shown underneath. You can purchase up to 19 keyfobs.
Armed Disarmed Armed Disarmed
Perimeter Partial Perimeter Partial
Arming Arming Arming Arming
LEDs
The LEDs on the panel provides information on the system status, e.g. activation,
deactivation, alarm and power fault conditions. If the yellow LED flashes, this may mean
that it is nearing time to change batteries in room sensors etc. The alarm will
automatically send a message to G4S Service Center, which will make sure that the
batteries are changed before they run completely dry. There will typically be 2-3 months
of battery back when the LED starts to flash.
Photo activation of alarm
There are three activation modes: Full, Part and Perimeter. With these modes you can
activate (Arm) the system in various ways.
Full Arming: Full Arming activates the entire system. This arming
method is used when you intend to leave your home, leaving the
premises empty.
Partial Arming: Part Arming enables you to arm a section of your
home while remaining on a different part of the premises.
Perimeter Arming: Perimeter Arming enables you to activate the
perimeter zones (the windows and doors of your home) enabling you to
move freely within the protected area.
The options for your home depend on what is agreed with the installer.
Disarming the system
When you walk through the front door the countdown begins for entering the disarming
code. You must disarm (disconnect) the alarm during this timeframe and the system will
not trigger an alarm.
Remote Activation / deactivation via text messaging.
If you have chosen GSM solution and chosen "text arm and disarming", you can remotely
control your alarm by sending text commands from a mobile phone to the alarm.
The following example shows how
you disarm the alarm:
The following example shows how
to arm the alarm:
"Your code" is your user code.
These commands are sent to the alarm’s
cell no., as provided to you by your installer if you have opted for this option.