Momentum Aria User manual

Aria
QUICK START GUIDE

Assembly Guide
Mounting
Bracket
Bracket Screws
Wire Nuts
Gasket
Junction Box
(not included)

Bracket
Screw
Mounting
Base
Mounting Base
Screw
Floodlight

Aria Floodlight
Gasket
Mounting Bracket
Screwdriver
Wire Nuts (x3)
#8 Long Bracket Screw
#10, #8, #6 Short Bracket
Screws (x2 each)
#10 #8 #6
Note: There are three sizes of screws provided. #8 is the most
commonly used, however your junction box may use #10 or #6 size
screws instead. Make sure to use the screw size that fits your
junction box.
What’s Included

Shut OFF the power at the fuse or
circuit breaker box.
DO NOT rely on a wall switch alone to
turn off the power.
If you’re unsure which switch it isto
turn off the floodlight power, please
consult with a licensed electrician.
Make sure your setup location will have
strong Wi-Fi reception.
WARNING: Failing to shut off the
power could result in a serious injury,
electrical shock, and/or risk of fire.
Before you Begin

Download the Momentum App from
the Apple App Store or Google Play.
You may also scan the QR code above
for the direct link to the app.
Create a new account if you don’t have
one already.
Important:Make sure the app you
download matches the same logo as
shown above.
Step 1: Download the app

Use a screwdriver or another tool to
remove your existing floodlight from
the junction box.
Disconnect the three sets of wires from
the floodlight.
If there is a mounting bracket attached
to your junction box, you may remove
that as well.
Step 2: Remove your existing floodlight

Use the provided screws in the box to
installthe mounting bracket onto your
junction box. Make sure it is tight and
secure.
With the provided gasket, peel off the
white tape and stick that side around
the opening in the wall. Make sure the
center hole lines up with the center
bracket hole and that there are no
openings around the gasket.
Step 3: Install the bracket and gasket

You should see three sets of wires from
both your wall and the Aria mounting
base:a ground wire (usually green or
copper), black wire, and white wire.
Use the provided wire nuts to twist the
open ends of the matching wires
together.
Step 4: Connect the wires

First, make sure that the Aria mounting
base is set properly.
With the provided long screw, push the
screw through the middle screw-hole of
the mounting base. Use the provided
screwdriver to tightly secure it.
Ensure that the gasket and base is tight
and does not move.
Step 5: Install the mounting base

The floodlight can now be mounted
ontothe mounting base. Make sure the
screw-hole at the top matches on both
the mounting plate and the floodlight,
then use the provided screw and
screwdriver to screw them tightly in
place.
Step 6: Mount the Aria floodlight

Turn on the power from the power
breaker. Once the power is back on,a
sound will play from the Aria notifying
you that it’s ready to pair.
Go back into the Momentum app and
follow the in-app screens to complete
the pairing process.
Step 8: Pair the Aria

Reset
1. To perform a factory reset, you must
open the camera and hold its internal
reset button for 10 seconds.
2. If you want to pair the Aria to a
different Wi-Fi network, hold the reset
button for 3 seconds and redo the
pairing process again.
Quick tips
Reset button

Light Indicators & Status
1. Solid Red – Booting
2. Blinking Red – Failed to connect to
Wi-Fi
3. Double Blinking Blue – Ready to
connect to Wi-Fi
4. Blinking Blue – Aria is connected to
Wi-Fi
5. Solid Blue – User is live streaming
Quick tips

Apollo Tech USA, Inc.
8608 Utica Ave. #220,
Rancho Cucamonga, CA 91730
Customer Service: [phone]
E-mail: [e-mail]
Version 1.0

www.momentumcam.com