Galaxy GLX RV-100 User manual

RV-100 DIGITAL REVERB

OWNER’S MANUAL
BATTERY REPLACEMENT
1. Loosen the screw on the pedal to
open it.
2. Remove the battery from the
battery compartment and
disconnect the battery cable.
3. Connect a new battery to the
battery cable and put it back
in the battery compartment.
Make sure that the polarity
of the battery is correct and the
battery cable does not interfere with
the spring or pedal cover.
4. Push the coil spring into the spring
base and close the pedal.
5. Insert the thumb screw into the guide bush hole and firmly tighten the
screw.
IMPORTANT NOTES
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this apparatus near water.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers,
stoves or any other apparatus (including amplifiers) that create heat.
8. WARNING: to reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
9. Protect the power cord from being walked on or being pinched.
10. Unplug this apparatus when unused for long periods of time.
11. There are no user serviceable parts inside. All servicing has to be done by
qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as when the power supply cord or plug
is damaged, when liquid has been spilled or objects have fallen into the
apparatus, when the apparatus has been exposed to rain or moisture, when
the apparatus does not operate normally or when it has been dropped.
PANEL DESCRIPTION
1. AC Adaptor Jack: Connect an AC adaptor (100-140V/50-60Hz).
An AC adaptor allows long and secure operation without worrying about
battery life.
Use the proper supply for your area’s Mains line voltage.
2. Indicator LED: This LED indicates when the effect is turned on.
• Operating on battery power only: when the LED becomes dim or does
not light the battery needs to be replaced.
INSTRUCTIONS
Thanks for purchasing our product. In order to make the best use of your
RV-100, please read the following carefully.
FEATURES
The RV-100 is a high quality, multifunction digital reverb effect. It features
spring, plate, hall, room, gate and modulate reverb. Stereo output and studio
quality sound ensure that the pedal can be used in any environment.
3. Level Knob: Use this control to adjust the output level of the effect.
4. Tone Knob: Use this control to adjust the tone of the reverb. Rotate
clockwise for a brighter sound and counter-clockwise for a warm sound.
5. Time Knob: Use this control to adjust the reverb time.
6. Mode Knob: Use this control to switch the reverb mode. Ordinary reverbs
include spring, plate, hall, room and gate. Specialized reverbs include
modulate.
7. Output Jacks A/B: Use the jacks to connect an amplifier or other units.
Use Jack A for mono output.
8. Pedal: Press the pedal to turn the effect on and off.
9. Thumb Screw: Loosen the screw to open the pedal for battery
replacement. (For details of the battery replacement, see “BATTERY
REPLACEMENT”)
10. Input Jacks A/B: Connect your instrument to this jack. To prolong battery
life, disconnect all cables from the pedal when it’s not in use.
SPECIFICATIONS
Input Impedance 1MΩ
Output impedance 1kΩ
Recommended Load
Impedance 10kΩ or greater
Residual Noise -92dBu (IHF-A, Typ.)
Power Supply DC 9V; Dry Battery (6F22/9V), AC adaptor
Connections Input A (Mono) / B,
Output A (Mono) / B,
AC Adaptor
Controls Pedal Switch, Level, Tone,
Time, Mode
Indicator Check indicator (serves also
as battery check indicator)
Current draw 55mA, (DC 9V)
Dimensions 72*128*60 mm.
Weight 415g (no battery)
Option AC adaptor
RV-100 DIGITAL REVERB
CONNECTIONS
1. Connecting an instrument to this jack will automatically switch the unit on.
Be sure to disconnect the cord from this jack when the unit is not being
used.
2. Before connecting or disconnecting any instrument, make sure that the
volume of the amplifier is turned down.
3. For monaural output, use Output Jack A. Both the dry and the processed
signal are output.
4. For stereo use:
Output A: only the processed
signal is output.
Output B: only the dry
(unprocessed) signal is
output.
5. When you use a high output
guitar, the sound may be
distorted. If distortion occurs,
turn down the volume of the
guitar or use a limiter.