Galvin Engineering CliniMix 100.91.10.20 Instruction sheet
© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 14 September 2022, Page 1of 4
CliniMix®BS Lead Safe Thermostatic Cartridge
Assembly for CMV2 Low Flow
PRODUCT CODES
- 100.91.10.20
SPECIFICATIONS
−Designed to be used with CliniMix®CMV2 only.
−Lead Safebrass construction.*
IMPORTANT: All CliniMix®spare parts are tested and leave our premises in good working order.
Water Act (SDWAad when used with respect
TECHNICAL DATA
Inlet
N/A
Outlet
N/A
Headwork
N/A
Working Pressure Range (kPa)
Min
20
Max
500
Working Temperature Range (°C)
Min
5
Max
85
Nominal Flow Rate (LPM)
N/A
Construction
Brass
Finish
Brass
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.
DIMENSIONS
© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 14 September 2022, Page 2of 4
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements.
Water and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of the
product.
1. Close the mains and deinstall Spout
- Close off both (hot and cold) water
mains or power main. Ensure water is
not flowing when hand waving in front
of the sensor.
- Loosen grab screw to unlock the
spout. Pull and gently remove the
spout.
- Removing the disinfection key cover
plug might help with detaching the
faceplate in next steps.
2. Remove the faceplate
- Loosen the grub screw shown on above
picture.
- Unscrew the locking nut and remove.
Remove the flange.
- Carefully remove the faceplate.
- Do not change the position of the backnut if
not necessary.
-
connections.
3. Ensure water is closed
-
position.
4. Remove locking ring
- Break/remove the plastic lock in the centre
of the thermostatic mixing valve.
Plastic ring
© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 14 September 2022, Page 3of 4
5. Remove cartridge
- Use spanner size 28mm and turn the
cartridge in counterclockwise direction
until it reaches the end of its threads.
Pull the thermostatic cartridge out of
the mixer body. Open both (hot and
cold) water mains and check for leaks.
- Open both isolating valves and check
for leaks.
Note: The flow might start from the inner part of the spout if the
main power remained on.
- Remove the cartridge by hand
6. Assembly and testing
- New cartridge can now be re-installed,
by screwing into the mixer body until it
reaches a firm stop. The cartridge
should be tightened to a torque of
15Nm. Re-install or install new plastic
lock supplied with the new cartridge.
- When service is complete, slowly turn the
cold-
position and inspect mixer body for leaks.
Repeat with hot water isolation ball valve.
- Reassemble by reversing steps 1 and 2.
- Re-commission the mixer as per
commissioning procedure (see units
installation instruction for details).
Product Installation Guidelines
Version 1, 14 September 2022, Page 4of 4
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including
but not limited to the implied warranties of merchantability and fitness for a particular purpose.
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Water is not flowing
Water manis closed
Open water main supply, ensure
isolation valves are in open position
Power mains off
Turn on the power
Mixed water is not correct
Unit not re-commitioned
Re-commision the mixer as per units
installation instruction
Supply water conditions out
of requrements
Ansure water supply conditions are as
per requirements (see units installation
instruction for details)
