Galvin Specialised Ezy-Drink CP-BS Lead Safe Instruction sheet

Version 1,30th April 2020, Page 1of 5
Ezy-Drink®CP-BS Lead Safe™ Hob Mounted Bottle
Filler Tap with Reduced Flange
PRODUCT CODES:
- 170.13.33.00
SPECIFICATIONS
Chrome plated assembly for durability and easy cleaning
Lead Safe™ brass construction
Reduced flange size for installations with limited space.
IMPORTANT: All Ezy-Drink®Bottle Filler taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
As ‘lead free’ is not currently defined by low in Australia and New Zealand, we have based our definition of Lead Safe™ on the requirements of s1417 of the USA’s Safe Drinking Water Act (SDWA)
and the relevant US standards NSF61 / NSF372. The SDWA defines ‘lead free’ as “not more than a weighted average of 0.25% lead when used with respect to the wetted surface of pipes, pipe fittings,
plumbing fittings and fixtures”.
TECHNICAL DATA
Inlet
½” BSP – Male
Outlet
Gooseneck
Headworks
Push Button
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
60
Nominal Flow Rate (LPM)
4.0
Construction
Brass
Finish
Chrome Plate
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without notice.
TOOLS REQUIRED
Hex Key
Thread tape
Adjustable spanner

Version 1, 1 May 2020, Page 2of 5
Version 1,30th April 2020, Page 2of 5
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with
these provisions shall void the product warranty and may affect the performance of the product.
1. Disassemble
Remove nut & cup washer from assembly.
2. Fit bottle filler
Fit bottle filler to basin as shown.
PRE-INSTALLATION - MOUNTING DETAILS
If the mounting holes do not already exist, mark out and drill the holes in the bench/trough, as shown in
rough-in dimensions.
Note: Before installation, all lines must be flushed. We recommend that a line strainer be installed prior to the bottle
filler tap to eliminate any foreign material.
Rough-In Dimensions

Version 1, 1 May 2020, Page 3of 5
Version 1,30th April 2020, Page 3of 5
3. Secure bottle filler and connect water
Fit cup washer and nut.
Tighten assembly ensuring it cannot be
turned once installed.
Connect water inlet. Thread tape/sealant
should be used. Ensure the thread tape
doesn’t obscure the inlet opening.
4. Remove spout
Remove spout from assembly as shown.
The spout can be rotated to 4 different positions
to suit installation.
5. Fit & position spout
Position the spout in the desired position
ensuring the position hole lines up with the
grub screw as shown.
Ensure supplied O-Ring is fitted to the filler
inlet.
Insert the filler assembly into the outlet.
Note: We recommend a small amount of an
approved silicone grease is used on the o-ring
before assembly to ensure ease of fitment.
6. Secure spout
Once positioned and the alignment is correct
(see above), tighten the grub screw to secure
the outlet.
Align
Water Inlet

Version 1, 1 May 2020, Page 4of 5
Version 1,30th April 2020, Page 4of 5
7. Test
Once the bottle filler has been installed, turn on mains water and check for leaks and correct operation.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Leaks
Incorrectly installed.
Follow the installation instructions and
ensure the o-ring is correctly installed.
Check for debris in the outlet.
Spout still rotates
Grub screw incorrectly installed.
Ensure the spout inlet position hole is lined
up with the outlet grub screw hole. Re-
install grub screw.
Water is not flowing
Water is turned off
Turn on water
Inconsistent flow
Blocked top assembly
Remove top assembly and clean.

Version 1, 1 May 2020, Page 5of 5
Version 1,30th April 2020, Page 5of 5
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s
warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.