Gamber Johnson 7160-1028 User manual

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Rev.A INST-808
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Revision
© Copyright 2017 Gamber-Johnson, LLC
7160-1028
VEHICLE BASE - JEEP COMPASS 2017+
PS-001
Form
Printing Spec:
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Product
INSTALLATION INSTRUCTIONS
•You must read and fo ow a of these insta ation instructions. Fai ure to fo ow the insta ation
instructions may resu t in serious bodi y injury or death
•DO NOT insta or use this assemb y in the area in which the airbag on the vehic e may be
dep oyed. The insta er and user of this assemb y are responsib e for insta ing and using this
assemb y outside the area in which an airbag may be dep oyed. (See Product Mounting
Disc aimer Be ow)
•Keep these insta ation instructions with the product and readi y avai ab e in the vehic e
for future reference of other users of the product.
•Additiona copies of the insta ation instruction can be obtained from Gamber-Johnson.
If you need assistance or have any questions, go to www.gamberjohnson.com or
ca Gamber-Johnson at 1-800-456-6868.
•DO NOT remove the warning abe form product under any circumstances.
•This assemb y shou d not be positioned in the area where the airbag may be dep oyed.
•DO NOT position the equipment in front of an airbag. Equipment positioned in front of an
airbag may cause serious injury or death if an airbag is activated.
•If insta ation of the equipment requires that the equipment be p aced in front of an airbag,
the airbag shou d be deactivated. In order to secure permission for deactivating the airbag
you must contact the Nationa Highway Traffic Safety Administration at 1-800-424-9393 to
gain permission to do so. If you have any questions or need assistance, ca Gamber-Johnson
at 1-800-456-6868.
•High speed vehic e turns may cause parts of the assemb y to swive , interfering with the
driver or other equipment.
RISER
VEHICLE BASE
MOUNTING HOLES

To Insta :
Using a T45 torx bit, remove the front passenger seat bo ts and oosen the rear seat 1.
bo ts. The seat may need to be moved forward or backwards to access the seat
bo ts.
Lift the passenger seat and p ace the base between the seat and the vehic e f oor.2.
Reinsta the front passenger seat bo ts and tighten. Tighten the rear passenger seat 3.
bo ts.
Attach the riser using the 3/8-16 hex head bo ts and washers inc uded in the 4.
hardware bag.
To mount a po e onto the riser use the 3/8-16 carriage bo ts,washers and nuts 5.
inc uded in the po e's hardware bag.
Base Installed With DS-LOWER-9 Pole
FRONT SEAT BOLT
POLERISER
BASE