GAMEMAX Abyss TR User manual

INSTALLATION GUIDE
CopyRight @ 2020.6

1
Front Back Top
Specification
Model No.
Dimension
N/A
3.5”HDD*3/2.5”SSD*3
E-ATX/ATX/Micro-ATX/ITX
170mm
USB3.0*2,USB2.0*2 (User option)
Abyss TR (MFG. M908 TR)
210(W)x 527(H)x 512(L)mm
Steel/ABS
7 Slots Support VGA card 420mm
Top: 120mm*3/140mm*2 (User option)
Front: 120mm*2 (User option)
Rear: 120mm*1 (User option)
Bottom dust filter*1; Top dust filter*1
HD Audio/MIC
Material
M/B Type
5.25"Drive Bay
HDD Drive Bay
Expansion Slots
Height of CPU
Cooling system
Dust filter
I/O Panel
RGB LED*5 connector
Fan speed*5 connector
RGB+PWM control
Standard ATX PSUPSU
Bottom Side

2
1
3
5
7
9
13
11
ODD place
15
2
4
6
8
10
Front fan place
Top dust filter
12
14
Top fan place
Top panel
16
16
Front panel
Left side panel
Rear fan place
PSU Place
SSD rack
Foot
Right side panel
M/B place
3.5/2.5 HDD Rack
Bottom dust filter
RGB+PWM
control board

3
Power S/W
M/B Connector
USB3.1 GEN1
M/B I/O Connector
USB2.0
M/B I/O Connector
H/D audio
M/B Connector
HDD LED
M/B Connector
Fan Contrller
Fan Connector
Reset S/W
M/B Connector
Power LED S/W
M/B Connector
LED M/B
Connector

How to install M/B
Clean dust filters
Remove the dust filter from the PSU position
How to install PSU
Insert PSU Fix with screws
4
How to install 3.5"HDD&2.5"SSD
Install M/BInsert the hard drive into placeRemove the bay bracket

How to install 2.5"SSD
SSD place 1
5
Install SSD,fix with screwsLosen screws,remove SSD bracket Insert SSD bracket into place
Fix with screws
SSD place 2
Fix with screwsInsert SSD

6
Power for fan
controller 4pin
Cable connection instrution
HDD LED M/B connector
POWER LED M/B connector
Reset S/W M/B connector
Power S/W M/B connector
Power for fan
controller 3pin

7
How to install the water cooling
Put the radiator in top place
Put the radiator in front placePut the radiator in the rear
panel then fix with screws Fix with screws
Fix with screws
Front panel : 240/360mm
Top panel: 280/360mm
Rear panel: 120mm
The size of water-cooling:

8
( User option )
No.1 How to install VGAcard fix
unit (User option)
No.2 How to install water tank(User option)
Fix with screws
Install water tank
No.3 How to use RAM cooler guide install2.5"/3.5"HDD/SSD
1、Loosen screw 1,adjust A
3、Loosen screw 3 and screw 4 ,adjust B
2、Loosen screw 2 and screw 5,adjust C

9
HV1.7 ARGB (RAINBOW) HUB CONTROLLER
1. Product features
1.18 color models.
2. Mode and color adjustment.
3. Brightness adjustment.（can be Selection）
4. SATA power supply.
5. Compatible with programmable RGB interface of
RAINBOW motherboard.
6. Can connect LED strip of ASUS.
Schematic diagram of connection
- Switch mode
In the controller mode, press the MODE key 3S, and the white light
flickers. If you connue to press the key, the light will be turned off.
Press the MODE key again to turn on the light.
- Mode and color buon
Short press one mes mode and color buon to change mode.Short
press two mes mode and color buons to change colors in the
same mode.
- Brightness buon
Short press brightness buon can adjust the brightness of LED.
This funcon depends on different versions to decide whether to
provide.
3. Interface definitions
3-1. ARGB
ARGB connect fan or light bar. The triangle mark on the plug is
aligned with the arrow on the controller.
3-2. MB ARGB
MB ARGB is connected to the motherboard ARGB interface.
The triangle mark on the plug is aligned with the arrow on the
controller.
3-3. SATA
SATA is the power supply interface and Output 5V DC voltage.
3-4. SW
SW is the switch interface. Some products have mode and
color control functions, and some products have brightness
adjustment function.
3-5. STRIP
Can connect lights strip of ASUS for 3PIN.
LED strip
connetor
Manual control switch
connetion port
Rainbow
connector
Connector to PSU
Motherboard
Rainbow
connector
1：mode and color
2：GND
3：brightness
1 2 3
2. Functional description
2-1. Change MB and controller mode.
The default mode is controller mode. Press the MODE key for 3s,
and the white light flickers. It prompts you to switch into MB mode,
release the key and enter the MB mode. After entering the MB mode,
press the MODE key and enter the controller mode again.
2-2. Switch mode
In the controller mode, press the MODE key 3S, and the white light
flickers. If you continue to press the key, the light will be turned off.
Press the MODE key again to turn on the light.
2-3. Memory function.
This controller has memory function.
2-4. Mode and color button.
Short press one time mode and color button to change mode.
Short press two times mode and color button to change colors in the
same mode.
2-5. Brightness button
Short press brightness button can adjust the brightness of LED.
This function depends on different versions to decide whether to
provide.
2-6. AURA SYNC
After connecting the interface, the light control of the MB can be
realized by key-press operation.
2-7. Strip
It can be connected LED strip with ASUS standard.