Ganz ZN-DNT352XE-MIR User manual

01A.01 2
INFORMATION TO USER
CAUTION
RISK OF ELECTRIC SHOCK,
DO NOT OPEN
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
CONTACT QUALIFIED SERVICE PERSONNEL FOR INTERNAL PARTS.
This symbol is intended to alert the user the presence of un-insulated
“dangerous voltage”within the product’s enclosure, which may be sufficient
magnitude to constitute a electric shock risk to persons.
!
This symbol is intended to alert the user the presence of important operating
and maintenance (servicing) instructions within the guide manual.

01A.01 3
Table of Contents
1. FEATURES ................................................................................................................. 4
2. PACKAGE CONTENTS ................................................................................................ 5
3. PART NAMES ............................................................................................................ 6
4. INSTALLATION .......................................................................................................... 7
4.1. Installation Template......................................................................................................8
4.3. Setting the Image Attribute ............................................................................................9
5. CONNECTIONS ........................................................................................................ 10
6. CONFIGURATION .................................................................................................... 13
6.1.Set up network environment.........................................................................................13
6.1.1. Generic IP Environment .........................................................................................13
6.1.2. Custom IP Environment .........................................................................................14
6.2. View video on web page...............................................................................................15
6.2.1. View video using IPAdmin Tool ..............................................................................16
6.3. Reset............................................................................................................................17
6.4. Factory Default.............................................................................................................17
APPENDIX (A): SPECIFICATIONS.................................................................................. 18
Summary ............................................................................................................................18
Electrical Characteristics .....................................................................................................19
Environment Condition .......................................................................................................19
Mechanical Condition .........................................................................................................19
APPENDIX (B): POWER OVER ETHERNET .................................................................... 20
PoE compatibility ................................................................................................................20
Power classification.............................................................................................................20
APPENDIX (C): DIMENSIONS....................................................................................... 21
APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE................................... 22
REVISION HISTORY ..................................................................................................... 23

01A.01 4
1. FEATURES
Camera
Full HD outdoor dome IP camera (Vandal proof)
High quality compression in real time streaming
1/2.7” High Quality CMOS Image Sensor
True Day / Night (ICR) and WDR
Improvement of color rolling suppression
Remote Zoom/Focus Control(One Click AF)
36 IR LEDs
Streaming
Dual streaming mode (such as different codec/resolution/bit rate and so on.)
De-interlacing on DSP
Burnt-in text supported
Unicast/Multicast supported
Video/Audio
Video compression: H.264/MPEG4 (Planned for the future release.)/MJPEG,
25/30FPS@1080p(PAL/NTSC)
Audio compression: G.711(µLaw, aLaw)/PCM
Analog video out for external monitors
Video motion detection supported
Two-way mono audio supported
Network
RTSP/ HTTP protocol supported
10/100 Base-T Ethernet
Additional Features
Micro SD card support
PoE support
Built-in Video Content Analysis
Internal fan and heater
IP66 certified
SDK (Software Development Kit) provided

01A.01 5
2. PACKAGE CONTENTS
Unpack carefully and handle the equipment with care. The packaging contains:
Camera
DC power adaptor
DC Jack Cable
9-pin and 2-pin terminal block
Video out cable
Screws and anchors
Installation template
Hex wrench driver
Quick installation guide
Silicon waterproof band
Clamping core
To prevent electromagnetic interference
Note
i
The above contents are subject to change without prior notice.

01A.01 6
3. PART NAMES
①Fan
The fan and heater (underneath the black panel) are implemented for controlling temperature and mois
ture of the internal device.
②Reset button
The reset button can be used for restarting the device or resetting it to Factory Default. Refer to 6.3. Re
set and 6.4. Factory Default for more details. Reset button is located under PCB.
③Output configuration switch
Refer to 4.2.Setting the Lens Positions for more information on the switch
④Video output, audio and IO terminal connector
A 9-pin terminal block is included in the device package. Connect this terminal block into this connector f
or cable connection of video output, audio input/output and digital input/output
⑤LAN connector
RJ45 LAN connector for 10/100 Base-T Ethernet.
⑥Micro SD card slot
Memory card slot for external storage.
⑦Power Adaptor Connector (DC 12V)
DC12V 3.5A adapter for power supply.







* Models herein and their appearance are subject to change without any prior notice.


01A.01 7
4. INSTALLATION
Caution
!
To prevent products from damaging, place the camera on stable and non-vibratin
g surfaces. If the stability is in doubt, consult with safety personnel for reinforcem
ents, and then proceed with the installation.
1) Place the installation template (paper)
that is included in the package on the
desired installation surface.
2) Drill three holes in correct positions
based on the template paper, and insert
anchor blocks into the holes.
3) Place the waterproof silicon band on the
bottom plate of the device and make it
align with screw holes.
4) Place the camera body to the
installation surface and match three
alignment holes with three anchor blocks.
Then tighten the surface anchor studs.
5) Connect all the required cables to the
camera.
6) Adjust the lens position. Detailed
information can be found in 4.2. Setting
the Lens Position.
7) Place the dome cover on the main body
of the camera. Dome cover has three
alignment holes that match camera body’s
alignment holes.
8) Once properly placed, insert screws into
the three holes of the body and tighten
them up.

01A.01 8
4.1. Installation Template
Caution
!
Installation template image’s size scale in this installation guide is not 1:1.
The correct-size template design paper can be found inside the package separ
ately.
Installation template
3502 V1.0

01A.01 9
4.2. Setting the Lens Position
Instruction below describes how to set the lens positions and manually adjust zoom and focus.
1) Remove the dome cover.
2) Set the lens position by rotating the camera gimbal; to pan, rotate the reinforced lower
body of the gimbal; to tilt, vertically adjust the camera gimbal.
Caution
!
Refrain from continuously rotating the camera gimbal with excessive force to a
single direction as it is attached with the IR-LED cable inside the dome.
3) The figure and table below explains the lens switch settings.
4.3. Setting the Image Attribute
Through the camera’s webpage, users can configure image settings.
The camera image’s brightness, contrast, saturation and sharpness are adjustable through the
image settings. (Setup > Video & Audio > Camera).
C. Tilt the lens by vertically
adjusting the camera gimbal
B. To pan, rotate the lower
body of the camera gimbal
A. To adjust lens position,
rotate the camera gimbal
SW1
SW2
SW3
PAL/NTSC
TELE
WIDE
SW4
SW5
SW6
FAR
NEAR
Auto-
Focus

01A.01 10
5. CONNECTIONS
①Audio input/output
The camera has a mono audio input and a mono audio output. Due to low audio output power,
an amplified speaker is recommended for enhanced sound (Do not connect a headphone or
earphone directly to the camera)
②Analog video output connection
Connect a display device (such as a monitor) to the video output connector and check if the
camera is installed properly streaming the images.
③Sensor (DI) connection
The camera provides 1 channel D/I. It can be connected to either a voltage type sensor or a
relay type sensor as the following figures. Settings can be done through the camera’s webpage.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
Input voltage threshold: 1.5V
Mic
Amp Speaker
ETHERNET MICRO SD DC12V
DO DI
1OutOut 1
VIDEO
C C In
AUDIO
+
Reset
SW1 SW2 SW3
SW5 SW6
N / A N / A
N / A N / A
SW1
SW2
SW3
SW4
SW5
SW6




ETHERNET MICRO SD DC12V
DO DI
1OutOut 1
VIDEO
C C In
AUDIO
+
Reset
SW1 SW2 SW3
SW5 SW6
N / A N / A
N / A N / A
SW1
SW2
SW3
SW4
SW5
SW6



01A.01 11
Caution
!
Do not exceed the maximum input voltage or relay rate.
④Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VDC 50mA
Caution
!
Do not exceed the maximum relay rating.
DO
COM
Relay Type
Device
Internal
+3.3V
DI
COM
DI
COM
+
-
Relay Type
Voltage Type
+
-
Output of
Sensor
Output of
Sensor
Internal
Internal
+
-

01A.01 12
⑤LAN connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Connect a LAN cable.
When the device is connected, the orange LED stays on while green LED continues to blink.
⑥12V DC Power
A 12 DC power connector is required for this device.
12V
Red
Black
Green LED Orange LED

01A.01 13
6. CONFIGURATION
6.1.Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of
the device from converting the MAC address’s hexadecimal numbers, which is attached to the
device. Be sure that the device and PC are on a same area network before running the
installation.
6.1.1. Generic IP Environment
In case of generic private network environment where IP address 192.168.XXX.XXX are used,
users may view the live streaming images on a web page using the device’s default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal
Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
2. Start the Microsoft® Internet Explorer web browser and enter the address of the device.
3. Web streaming and device configurations are supported through ActiveX program. When the
ActiveX installation window appears, authorize and install the ActiveX.
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the last two set of hexadecimal numbers to decimal numbers.

01A.01 14
6.1.2. Custom IP Environment
IPAdminTool is provided with SDK at the following SDK path.
{SDK root}\BIN\TOOLS\AdminTool\
IPAdminTool is a management tool, which automatically scans all of the network products for
users to perform administrative tasks, which includes network configurations, firmware update,
device reboot, and device organizations.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select “IP Address”; IP Setup window appears.
3. In the IP Setup’s window, information under ‘Local Network information’ displays the
user/PC’s network area information. Those information need to be incorporated to the IP
Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP Address, which
are to be the unique numbers for the device. Refer to the image above for the setting
4. Click ‘Setup’ to complete the modification.
PC environment Info
Give new unique IP
address in last two sets

01A.01 15
6.2. View video on web page
Type the proper IP address to view the live streaming images through a web browser.
The default username and password is root / pass.
1. The browser asks to install the ActiveX. Click Allow.
2. Setup.exe installation link or pop-up window appears, depends on Microsoft® Internet
Explorer version. Proceed with rest of setup installation.

01A.01 16
Caution
!
3. Follow the instructions of the dialog boxes and complete the installation. Once the
installation is complete, start the web browser again and check if video stream is
displayed in the main view frame.
6.2.1. View video using IPAdmin Tool
IPAdminTool automatically searches all activated network encoders and IP cameras and shows
the product name, IP address, MAC address and etc. IPAdminTool is provided with SDK at the
following SDK path.
{SDK root}\BIN\TOOLS\AdminTool\
1. From the IPAdminTool’s product list, select the device by highlighting it.
2. Right-click the mouse and select web-view
3. The system’s default web browser opens the device’s address.
Whether directly accessing the streaming video through typing IP address on a
web page or taking steps through IPAdminTool, the ActiveX is needed to be
installed for the Microsoft® Internet Explorer to have the complete
configuration privileges.

01A.01 17
6.3. Reset
1. Push the Reset button and hold for 1~2 seonds.
2. Wait for the system to reboot.
6.4. Factory Default
1. Push reset button and hold for 5 seconds..
2. Release the Reset button when power LED blinks.
3. Wait for the system to reboot.
The factory default settings can be inferred as follows:
IP address: 192.168.xx.yy
Network mask: 255.255.0.0
Gateway: 192.168.0.1
User ID: root
Password: pass

01A.01 18
APPENDIX (A): SPECIFICATIONS
Summary
Camera Module
CMOS
Image Sensor
1/2.7” 1080p CMOS
Effective Pixels
1920x1080
Scanning system
Progressive scanning
ELECTRICAL
Resolution
1920 x 1080
Min.
Illumination
Color: 1.0 lux, F1.2
BW: 0 lux (IR LED ON)
AGC Control
Auto
Lens
Vari-Focal,
Remote Zoom/Focus
Control(One Click AF)F1.2
Day & Night
Removal IR Cut Filter
Video
Compression Format
H.264, MPEG-41, MJPEG Selectable per Stream
Number of Streams
Dual Stream, Configurable
Resolution
1920x1080, 1280x720, 800x450, 480x270, 320x180
Compression FPS
Full-frame @1080p
Motion Detection
Built-in
Burnt-in Text (Digital)
Video stream overlay text
Output
Analog video output for installation only
Audio
Input/output
1/1 channel
Compression Format
G.711
Function
Digital Input/output
1/1 channel
RS-485
Not supported
Network
10/100 Base-T
Power over Ethernet
Supported
Protocol
TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP, RTP/TCP,
SNTP, mDNS, UPnP, SMTP, SOCK, IGMP, DHCP,
FTP, DDNS, SSL v2/v3, IEEE 802.1X, SSH, SNMP v2/v3
SD Slot
Supported (MicroSD)
※Micro SD Card not included
1
Planned for the next release.

01A.01 19
Electrical Characteristics
Power Source
DC 12V / PoE IEEE802.3af (Class 0)
Power Consumption
1410mA (Heater On, IR-LED On)
Video Output
1 Vp-p, 75Ω, Composite
Audio Input
Linein, 1.43Vp-p(Min 1.35Vp-p, max 1.49 Vp-p), 39 KΩ
Audio Output
Lineout, 46mW Power, 16 Ω
D/I
Max 50mA@5VDC, TTL level 4.5V threshold
D/O
Max 500mA@24VAC or 1A@12VDC
On-state resistance: 50 Ω (max continuous)
Environment Condition
Operating Temperature
Operating Range
DC12V : -40˚C ~ 50˚C (-40˚F ~ 122˚F)
PoE : 0 ˚C ~ 50 ˚C (32˚F ~ 122˚F)
Cold Start
DC12V : -20˚C (-4˚F)
PoE: 0 ˚C (32˚F)
Operating Humidity
Up to 85% RH
Mechanical Condition
Material
Aluminum Die Casting
Color
White
Dimension
Housing : 115 (Ø) x 129(H) mm
Dome : 100(Ø) mm
Weight (Approx.)
1.2kg

01A.01 20
APPENDIX (B): POWER OVER ETHERNET
The Power over Ethernet (PoE) is designed to extract power from a conventional twisted pair
Category 5 Ethernet cable, conforming to the IEEE 802.3af Power-over-Ethernet (PoE) standard.
IEEE 802.3af allows for two power options for Category 5 cables.
The IEEE 802.3af-2003 standard allows up to 15.4 W power to device. However, 12.95W is the
maximum available power, as some power gets lost in the cable.
PoE has advantages over conventional power in such places where AC powers cannot be
reached or expensive to wire.
Note: For proper activation of 12V PoE, the Category 5 cable must be shorter than 140m and
conform the PoE standard.
PoE compatibility
With non-Power Sourcing Equipment (PSE)
When it is connected with non PSE, the power adaptor should be connected.
With power adaptor
Connecting both PSE and power adaptor does not do any harm to the product, but power
adaptor will be the only power source for the device as it has priority over PSE. In this case,
disconnecting power adaptor while it is operating will cause the device to reboot. And PoE will
be the power source for the device after the reboot.
Power classification
The PoE Power Class supported by the IP device is Class 0.
Class
Usage
Minimum Power Levels
Output at the PSE
Maximum Power Levels at
the Powered Device
0
Default
15.4W
0.44 to 12.95W
Note
i
Unlike the other way, disconnecting PSE or PoE doesn’t reboot the device as
long as a power adaptor is connected.