Ganz ZC-PT series User manual

Installation Guide
1
Preface
Information given in this manual was current when published. The company reserves the
right to revise and improve its products. All specifications are subject to change without
notice.
Notice
This manual provides installation information for the outdoor Integrated High
Speed Dome Camera. To work with the Dome Cameras, any installer or
technician must have the following minimum qualifications:
•A basic knowledge of CCTV systems and components
•A basic knowledge of electrical wiring and low-voltage electrical
hookups
•A basic knowledge of network system setting
•Have read this manual completely
Copyright
Under copyright laws, the contents of this installation guide may not be copied,
photocopied, translated, reproduced or reduced to any electronic medium or
machine-readable format, in whole or in part, without prior written permission
of the company.
Important Information
Before proceeding, please read and observe all instructions and warnings in
this manual. Retain this manual with the original bill of sale for future
reference and, if necessary, warranty service. When unpacking your unit,
check for missing or damaged items. If any item is missing, or if damage is
evident, DO NOT INSTALL OR OPERATE THIS PRODUCT. Contact your
dealer for assistance.
Regulation
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.

Installation Guide
2
This symbol on the product or on its packaging indicates
that this product shall not be treated as household waste in
accordance with Directive 2002/96/EC. Instead it shall be
handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By proper
waste handling of this product you ensure that it has no
negative consequences for the environment and human
health, which could otherwise be caused if this product is
thrown into the garbage bin. The recycling of materials will
help to conserve natural resources.
For more details information about recycling of this product,
please contact your local city office, your household waste
disposal service or the shop where you purchased the
product.
Compliance is evidenced by written declaration from our
suppliers, assuring that any potential trace contamination
levels of restricted substances are below the maximum
level set by EU Directive 2002/95/EC, or are exempted due
to their application.

Installation Guide
3
Warnings and Cautions
•Handle the camera carefully
Do not abuse the camera. Avoid striking, shaking, etc. The camera could
be damaged by improper handing or storage.
•Installing electricity wiring carefully
Ask qualified personnel of electrical wiring for the installation. Please note
that input electricity to the unit is at tolerance of DC 12V/AC 24V ± 10%.
The camera is capable of surge protection; ensure AC power model unit
grounded appropriately against damage of heavy current or electric
shock.
•Do not disassemble the camera
To prevent electric shock, do not remove screws or covers. There are no
user serviceable parts inside. Ask a qualified service person for servicing.
•Do not block cooling holes on the bracket
This camera has a cooling fan inside. Blocking the cooling holes leads to
build up of heat the camera and may cause malfunction.
•Do not operate the camera beyond the specified temperature,
humidity or power source ratings
Use the camera under conditions where temperature is between -50°C ~
50°C (-58°F ~ 122°F), and relative humidity is below 90%.
•Do not use strong or abrasive detergents when cleaning the camera
body
Use a dry cloth to clean the camera when it is dirty. In case the dirt is hard
to remove, use a mild detergent and wipe the camera gently.
•Never face the camera towards the sun
Do not aim the camera at bright objects. Whether the camera is in use or
not, never aim it at the sun or other extremely bright objects. Otherwise,
the camera may be smeared or damaged.

Installation Guide
4
Table of Contents
1. Introduction................................................................................................................6
2. Standard Package Content .......................................................................................7
3. Camera Setups and Cable Connection....................................................................9
3.1 Preparations for Dome Camera Setups ............................................................9
3.2 Dome Camera Setups.....................................................................................12
3.2.1 Switch Definition................................................................................12
3.2.2 Communication Switch Setting..........................................................13
Analog Dome Camera.......................................................................13
IP Dome Camera...............................................................................14
3.2.3 ID Setting (Analog Model)..................................................................14
3.2.4 Camera Control Protocol Setup (Analog Model)................................15
3.3 Cable Definition and Requirements.................................................................16
3.3.1 Cable Requirements..........................................................................16
3.3.2 22-Pin Data Cable .............................................................................16
Analog Dome Camera.......................................................................16
IP Dome Camera...............................................................................17
3.3.3 22-Pin Connector Definition...............................................................17
Analog Dome Camera.......................................................................18
IP Dome Camera...............................................................................18
3.3.4 RS-485 Connector Definition (Analog Model)....................................19
3.3.5 Cable Wiring and Connection............................................................19
3.3.6 Ethernet Cable Connection................................................................20
4. Dome Installation.....................................................................................................21
4.1 Dome Dimension.............................................................................................21
4.2 Optional Accessories.......................................................................................21
4.3 Ceiling Mounting with Straight Tube................................................................28
4.4 Wall Mount......................................................................................................30
4.4.1 Compact Pendent Mount...................................................................30
4.4.2 Standard Pendent Mount...................................................................32
4.4.3 Wall Box Mounting.............................................................................34
4.5 Corner Mount..................................................................................................36
4.5.1 Corner Standard Mounting Plate/Corner Plate Mini...........................36
4.5.2 Corner Thin/Wide Box Mounting........................................................38
4.6 Pole Mount......................................................................................................40
4.6.1 Pole Thin/Wide Direct Mounting ........................................................40
4.6.2 Pole Thin/Wide Box Mounting............................................................42
5. System Expansion...................................................................................................44
5.1 Connecting with Power Box............................................................................44

Installation Guide
5
5.2 Data Formats Transforming.............................................................................45
5.3 Signal Distribution...........................................................................................46
5.4 Coaxial Telemetry............................................................................................47
6. System Integration ..................................................................................................48
6.1 Using Pelco Keyboard.....................................................................................48
6.2 Using Philips Allegiant Keyboard.....................................................................49
Appendix A: Technical Specification .............................................................................50

Installation Guide
6
1. Introduction
With weather resistant feature, the Mini PTZ Camera is applicable to outdoor
installation. The PTZ Camera supports one cabling for easy installation, and
can be integrated with various digital surveillance products, such as DVRs,
Control Keyboards, and accessories for a total surveillance solution. In
addition, large set of built-in protocols provide connectivity to other
surveillance systems. The built-in protocols include DynaColor, Pelco, VCL,
Philips, AD-422, etc., which allow the Speed Dome Camera to be integrated
with other suppliers' surveillance systems.
General Operation Requirements:
A minimum of one control device is required for operation, such as a control
keyboard, a DVR or a PC. The Mini Speed Dome Camera contains a built-in
receiver that decodes commands from a control device.
Connect Dome Cameras to other devices, as shown in the diagram below, to
complete a video surveillance system.
NOTE: To extend the network distance up to 1.2 km (4000 feet) and to
protect the connected devices, it is highly recommended to place a
repeater at the mid-point. However, a repeater may be needed in the network
distance less than 1.2 km if the used cables are not the CAT 5, 24-gauge
cables; also see 3.3.4 RS-485 Connector Definition (Analog).Refer to the
repeater’s manual for detailed information.

Installation Guide
7
2. Standard Package Content
Before proceeding, please check the box contains the items listed here. If any
item is missing or has defects, DO NOT install or operate the product and
contact your dealer for assistance.
Analog Dome Camera Package
Dome Camera with
Outdoor Mount Kit
Data Cable for Power Supply, Video,
Alarm and RS-485 (AC 24V)
Lubricant
Waterproof Rubber
M3 Standard Screw (x1)
M3 Security Screw (x1)
M5 Standard Screw (x1)
M5 Security Screw (x1)
Security Torx
Optical Cover
Quick Guide
CD: Operation Manuals

Installation Guide
8
IP Dome Camera Package
Dome Camera with
Outdoor Mount Kit
Data Cable for Power Supply, Video,
Audio and Alarm (AC 24V)
Lubricant
Waterproof Rubber
M3 Standard Screw (x1)
M3 Security Screw (x1)
M5 Standard Screw (x1)
M5 Security Screw (x1)
Security Torx
Optical Cover
Quick Guide
CD: Operation
Manuals

Installation Guide
9
3. Camera Setups and Cable Connection
Before installing or connecting the Dome Camera, please refer to this section
and complete preparations for Dome Camera setups and various switch
settings.
3.1 Preparations for Dome Camera Setups
The following installation procedure is for the outdoor Dome Camera
equipped with the sunshield. Please follow the steps below to install dome
cover and detach the Outdoor Mount Kit from the camera body for switch
setups.
STEP 1
Unpack the Dome Camera’s
package and take out the Dome
Camera unit.
STEP 2
Turn the Dome Camera upside
down and place it on the
cushion. Then rotate the Outdoor
Mount Kit counterclockwise and
detach it from the camera body.
STEP 3
Remove the protective cover and
PE sheet from the camera.

Installation Guide
10
STEP 4
Smear some lubricant on the
surface of the dome cover’s
waterproof rubber ring.
Then attach the dome cover to
the camera body by first aligning
the center point on the dome
cover with one of the four holes
on the dome camera housing as
shown in the figure.
STEP 5
Gently press down the dome
cover with two hands on the side
of it. Make sure the two Slotted
Screws and the screw hole on
the dome cover align with the
three holes on the camera
housing.
DO NOT press the dome cover
from the top of it as shown in the
figure; this might cause damage
to the Dome Camera.

Installation Guide
11
STEP 6
Screw the dome cover and
camera body together with the
supplied M3 Standard/Security
Screw. For fastening the Security
Screw, please use the supplied
Security Torx.
STEP 7
Then tighten the two Slotted
Screws on the camera housing
as shown in the figure by turning
them counterclockwise.
STEP 8
Set the switches located on the
bottom of the Dome Camera.
Refer to section 3.2 Dome
Camera Setups for detailed
information about various switch
setting.

Installation Guide
12
3.2 Dome Camera Setups
Before connecting the Dome Camera to other devices of CCTV system,
please complete the Dome Camera’s ID and communication switch settings.
These switches are located on the bottom of the Dome Camera.
3.2.1 Switch Definition
Please refer to the following figure and table for switch location and
definitions.
Analog IP
A Camera Control Protocol Switch ANone
B Communication Switch BCommunication Switch
C None CRJ45 Connector
D 22-Pin Connector D22-Pin Connector
E ID Switch ENone
F Reserved FReset Buttons
G ISP Connector (for FW upgrade) GISP Connector (for FW upgrade)

Installation Guide
13
3.2.2 Communication Switch Setting
The table below shows the function of each switch within the Communication
Switch for the analog and IP Dome Cameras.
Analog Dome Camera
Communication Switch SW 1
SW 2 RS-485 Setting
SW 3 Termination
SW 4 Line Lock
SW 5 System Initialization
SW 6 Reserved
RS-485 is the interface that communicates the Dome Camera and its control
device; for this reason, the RS-485 setup of the dome and the control device
must be the same. The RS-485 default setting is half-duplex (see the diagram
follows). Please do not change the default setting without qualified specialist
or supplier’s notice. As for the SW 3 and SW 4, they are used for termination
and Line Lock adjustment respectively. The SW 5 is mainly used when users
want to restore the camera to the factory default status; moreover, once
firmware upgrade is carried out, users also need to reset the SW 5 afterward.
RS-485 Setting
Half-duplex
Full-duplex

Installation Guide
14
IP Dome Camera
The IP Dome Camera’s communication switches are specified in the table
below. Each switch’s default setting is shown as the figure below. DO NOT
change the default setting, or some functions may not work properly.
Communication Switch SW 1
SW 2 Audio Setting
SW 3 Termination
SW 4 Line Lock
SW 5 System Initialization
SW 6 Reserved
Turn on the SW 5 can restore the camera to the factory default status;
moreover, once firmware upgrade is carried out, users also need to reset the
SW 5 afterward.
3.2.3 ID Setting (Analog Model)
The way to set the analog and IP Dome Camera’s’ ID number is specified as
follows.
Please change the analog Dome Camera’s ID if there is more than one Dome
Camera in the same network. Use the switch to change your Speed Dome
Camera’s ID by setting the 10-bit dip switch. For instance, if the camera’s ID
is 006, set the SW-2 and SW-3 to “ON,” with the rest to “OFF,” the ID switch
should be set as shown below.
For switch configuration details, please refer to Appendix B: Switch Settings
Index Table in the Dome Camera’s User Manual.
NOTE: No two Dome Cameras should be given the same ID, or
communication conflict may occur.

Installation Guide
15
3.2.4 Camera Control Protocol Setup (Analog Model)
Define the protocol you are going to use basing on the devices of your
surveillance system. Generally, use one protocol even the devices are
provided from different manufacturers. Use the switch to set your camera
control protocol and the baud rate. Refer to the table below and turn the
arrow to choose a protocol for your Dome Camera.
Switch No. Protocol Baud Rate
00 VCL 9600
01 Pelco D 2400
02 Pelco P 4800
04 Chiper 9600
05 Philips 9600
07 DSCP 9600
08 AD422 4800
09 DM P 9600
11 Pelco D 4800
12 Pelco D 9600
13 Pelco P 2400
14 Pelco P 9600
15 JVC 9600
21 Kalatel-485 9600
22 Kalatel-422 4800
23 Panasonic 19200
Use the 6-bit dip switch (Camera Control Protocol Switch) to set your
camera’s control protocol and its baud rate.
If select protocol: Pelco D, which is of switch no. 01 and baud rate 2400, for
instance, set the SW-1 to “ON,” with the rest to “OFF,” as shown below.
For switch configuration details, please refer to Appendix B: Switch Settings
Index Table in the Dome Camera’s User Manual.

Installation Guide
16
3.3 Cable Definition and Requirements
For operation, the integrated Dome Camera requires the video cable to carry
the video signals to the remote viewing site, power cable to power the Dome
Camera and RS-485 data cable to carry commands from the control device.
3.3.1 Cable Requirements
For operation, the Speed Dome Cameras require video and Data Cables as
described below:
•The video cable sends video signals to a remote viewing site. Using a
coaxial cable to send video signals is recommended.
•RS-485 cable carries commands from a control device to the Dome
Cameras. A CAT 5, 24 gauge cable is recommended.
•The power cable provides AC 24V power supply to the Dome Camera.
NOTE: Ensure power supply corresponds with the Dome Camera’s
power requirement, or product impairment will occur. If any mistake
happens, please contact with a qualified maintenance engineer.
3.3.2 22-Pin Data Cable
The analog and IP Dome Camera’s Data Cables are illustrated respectively
as shown below.
Analog Dome Camera
The analog Dome Camera’s Data Cables is illustrated as shown below.

Installation Guide
17
NOTE: Be careful not to pull the cables improperly during installation.
Additionally, it is suggested to fasten the cables after cable connection
is completed. Furthermore, when wiring the AC 24V power cable,
make sure the Ground wire is inserted into the mid-pin of the terminal
block.
IP Dome Camera
The IP Dome Camera’s Data Cable is illustrated as follows.
3.3.3 22-Pin Connector Definition
With the 22-pin connector, installers can simply connect the power, video and
RS-485 cables to the Dome Camera at once. Particularly, the alarm pins are
serviceable for connecting alarm input and output devices, such as alarm
sensors, sirens or flashing lights with the surveillance system. The analog and
IP Dome Cameras’ 22-pin connector definition will also be specified as
follows.

Installation Guide
18
Analog Dome Camera
The analog Dome Camera’s 22-pin connector definition is listed as below.
Pin Definition Cable Pin Definition Cable
1AC 24-1/DC (＋)20AWG/18AWG 12 ALM-1
2ALM NC 13 ALM-3
3AC 24-2/DC (－)20AWG/18AWG 14 ALM-2
4ALM NO 15 ALM-4
5FG 20AWG/18AWG 16 ALM-5
6 ALM COM 17 ALM-6
7 T+ 18 ALM-7
8 R- 19 ALM-8
9 T- 20 ALM GND
10 R+
24AWG
21 VGND
11 ISOG 22 Video 20AWG
IP Dome Camera
The IP Dome Camera’s 22-pin connector definition is listed as below.
Pin Definition Cable Pin Definition Cable
1AC 24-1/DC (＋)20AWG/18AWG 12 ALM-1
2ALM NC 13 ALM-3
3AC 24-2/DC (－)20AWG/18AWG 14 ALM-2
4ALM NO 15 ALM-4
5FG 20AWG/18AWG 16 ALM-5
6 ALM COM 17 ALM-6
7 Audio in 18 ALM-7
8 Audio out 19 ALM-8
9 Audio GND 20 ALM GND
10 Audio GND
24AWG
21 VGND
11 ISOG 22 Video 20AWG
NOTE: For alarm connection, please refer to section 3.3.5 Cable
Wiring and Connection.

Installation Guide
19
3.3.4 RS-485 Connector Definition (Analog Model)
RS-485 is the interface that communicates the Dome Camera and its control
device. Please connect the control keyboard to the Dome Camera through
the terminal block. The recommended cables for RS-485 communication are
CAT 5 cables; maximum cable length for over 24-gauge wire is 4000 feet
(1219 meters). If the total cable length exceeds 4000 feet, using a repeater to
maintain the signals is recommended. Please refer to the figure and table
below for pin defination and wiring.
3.3.5 Cable Wiring and Connection
Users may need to do cable wiring when: (1) Connecting self-provided cords
to the connector housing instead of using the equipped Data Cable or (2)
Connecting alarm input and output devices. The table follows will illustrate the
way to wire cords into the connector housing.
Pin Corresponding Pins
(22-Pin Connector) Definition
1 7,10 T+, R+ (D+)
2~4 Reserved
5 8,9 T-, R- (D-)