Ganz ZN-DNT352XE SERIES User manual

03-2014-B 1

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 2
Precaution
Please read this manual carefully before installing the unit.
Never disassemble the camera. Unauthorized disassembly may cause equipment
failure or damage to the unit.
Please do not install the camera in a place exposed to direct sunlight.
Do not operate the camera in environments beyond the specified temperature.
Refer to “Environment Condition”on “APPENDIX (A) : SPECIFICATIONS”in this manual.
Before applying power to the camera, check the power source to ensure that it is
within the specifications. Refer to “Electrical Characteristics”on “APPENDIX (A) :
SPECIFICATIONS”

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 3
Table of Contents
Precaution................................................................................................................ 2
1. FEATURES............................................................................................................. 4
2. PACKAGE CONTENTS............................................................................................. 5
3. PART NAMES ........................................................................................................ 6
4. INSTALLATION ...................................................................................................... 8
4.1. Installing the camera.......................................................................................................... 8
4.2. Adjusting the angle of the camera................................................................................... 10
4.3. Adjusting zoom and focus ................................................................................................ 10
4.3.1. XE-xx models ............................................................................................................. 10
4.3.2. XE-Mxx models (Remote Zoom/Focus control models)............................................ 11
4.4. Setting the Image Attribute ............................................................................................. 12
5. CONNECTIONS.................................................................................................... 13
6. CONFIGURATION ................................................................................................ 16
6.1. Set up network environment ........................................................................................... 16
6.1.1. Generic IP Environment ............................................................................................ 16
6.1.2. Custom IP Environment............................................................................................. 17
6.2. View video on web page .................................................................................................. 18
6.2.1. ActiveX Installation.................................................................................................... 18
6.2.2. View video using IPAdmin Tool................................................................................. 19
6.3. Reset................................................................................................................................. 20
6.4. Factory Default................................................................................................................. 20
6.5. Safe Mode ........................................................................................................................ 21
APPENDIX (A): SPECIFICATIONS .............................................................................. 23
Summary ................................................................................................................................. 23
Electrical Characteristics ......................................................................................................... 25
Environment Condition ........................................................................................................... 25
Mechanical Condition ............................................................................................................. 26
APPENDIX (B): POWER OVER ETHERNET ................................................................. 27
PoE compatibility .................................................................................................................... 27
Power Comparison.................................................................................................................. 27
APPENDIX (C): DIMENSIONS ................................................................................... 28
APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE ................................. 29
REVISION HISTORY ................................................................................................. 30

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 4
1. FEATURES
Camera
SONY EXMOR 1/2.9” (XE-M model) and 1/2.7”1080p CMOS Image Sensor
True Day/Night
DC Auto Iris Lens
WDR
Remote Zoom/Focus Control (One click Focus) [XE-Mxx model only]
Weather Proof (IP66)
Vandal Proof (IK10)
Video
H.264 Baseline, Main, High profile(MPEG-4 Part 10 /AVC), MJPEG(Motion JPEG)
Max 30fps in 1080p
Text Overlay
Analog Video Output for 3 minutes (only for installation purpose)
Audio
Two-way Audio Streaming
G.711µLaw
Network
10 / 100 Base-T Ethernet
Integration
Software Development Kit (SDK) available
ONVIF Compliant (Profile S)
General
microSD slot
Power Over Ethernet (PoE)
Video Contents Analytics (VCA)
VCA Presence (Standard)
VCA Surveillance (Optional)

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 5
2. PACKAGE CONTENTS
Please unpack the package carefully and handle the equipment with care.
The package contains:
Camera
DC Power Adaptor
DC Power Jack Cable
Terminal Blocks
Video Output Cable
Screws and Anchors
Installation Template
Hex Wrench Driver
Quick Installation Guide
Cushion sheet
Ferrite Cores

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 6
3. PART NAMES
①Reset button
Use the button to restart the device or to reset it to Factory Default. Refer to “6.3. Reset”and “6.4. Fact
ory Default”for more details.
②Focus button(s)
Use the buttons to automatically/manually determine correct focus.
○
1
○
7
○
5
○
6
* Models and their appearance are subject to change without any prior notice.
○
8
Reset button
located on the PCB.
○
4
XE-xx models





* Models herein and their appearance are subject to change without any prior notice.
⑧
Reset button
located on the PCB.
XE-Mxx models

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 7
③Zoom button(s)
Use the buttons to manually determine correct zoom.
④PAL/NTSC button
Pressing the button cycles through PAL, NTSC, and no video output mode No video > PAL > NTSC.
⑤Terminal connector
Connector for cable connection of video output, audio input/output and digital input/output.
Refer to “5. Connections”for more details.
⑥LAN connector
RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)
⑦microSD slot
Supports up to 64GB. Recommend Class 4 and higher for HD recordings.
⑧Power Cable socket
Socket for the DC power jack cable/terminal included in the package (Use 12VDC adaptor for power
supply)

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 8
4. INSTALLATION
4.1. Installing the camera
Caution
!
Sealing gaps is recommended as gaps may appear after the camera
installation. Gaps may cause problems such as moisture, water leakage, and
etc., which negatively affect the operation of the camera if gaps appear but
remain unsealed.
Caution
!
To prevent products from damage, place the camera on stable and non-vibratin
g surfaces. If the stability is in doubt, consult safety personnel for reinforcemen
ts, and then proceed with the installation.
1) Place the installation template (outline
shown on the next page) included in the
package on the desired installation
surface.
2) Drill holes in correct positions based on
the template paper, and insert anchor
blocks into the holes.
3) Make sure the necessary cables including
a LAN cable and a power cable are
properly connected to the camera either
thru the ceiling or thru the groove around
the mounting plate.
4) Place the camera body and match the
alignment holes with the corresponding
anchor blocks and hold against the
mounting surface.
5) Tighten the anchor blocks with screws.
6) Adjust the angle of the camera. Refer to
“4.2.Adjusting the angle of the camera”
for more details.
7) Adjust zoom and focus of the camera.
Refer to “4.3. Adjusting zoom and focus”
for more details.
8) Place the dome cover on the main body
of the camera. Dome cover has three
alignment holes that match camera
body’s alignment holes.
9) Once properly placed, insert screws into
the three holes of the body and tighten
them up.

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 9
Installation Template
(Unit: m)
Caution
!
Installation template’s image size scale in this installation guide is not 1:1.
The correct-size template design paper can be found inside the package
separately.
Installation template
3502 V1.0
φ
152
φ152

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 10
4.2. Adjusting the angle of the camera
Adjust the lens to the desired position by manually moving its upper lens shell, reinforced body
or horizontal platform in the following directions.
Caution
!
Refrain from continuously rotating the camera gimbal with excessive force to a
single direction as it is attached with the IR-LED cable inside the dome.
4.3. Adjusting zoom and focus
4.3.1. XE-xx models
1) Zoom and focus pullers are located inside the camera gimbal. Rotate the gimbal
counterclockwise and pull to detach. While detaching, do not pull straight off as there is an IR
sensor and LED power cable connected to a cover. To attach the cover back, rotate the gimbal
while gently pushing it in.
5) Unscrew the focus puller by turning it counterclockwise. Move it left or right and adjust the
image focus. After the setting, tighten the focus puller again by turning it clockwise.
Zoom puller
Focus puller
C. Tilt the lens by vertically
adjusting the camera.
A. To adjust lens position,
rotate the camera gimbal
B. To pan, rotate the lower
body of the camera gimbal
4) Unscrewing the zoom puller will
allow users to adjust the lens zoom
position. After the setting, tighten up
the zoom puller again by turning it
clockwise.

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 11
4.3.2. XE-Mxx models (Remote Zoom/Focus control models)
Use Zoom In/Out buttons (TELE/WIDE) to adjust the camera’s angle of view.
Use Focus buttons (FAR/NEAR/Focus) to automatically/manually determine correct focus.
Lens Zoom/Focus adjustment can be fully controlled by web user interface too.
Refer to the provided “PixelPro GXi series Web Page User's Manual”for more details.
SW1
SW2
SW3
SW4
SW5
SW6
PAL/NTSC
TELE
WIDE
FAR
NEAR
One Push Focus

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 12
4.4. Setting the Image Attribute
Through the camera’s webpage, users can configure image settings. The menu of image
attribute is available under Video Appearance menu in Setup > Video & Audio > Camera. The
following features can be adjusted: Brightness, Contrast, Saturation, Sharpness and
Orientation
For more detailed information, refer to the provided “PixelPro GXi series Web Page User's
Manual”.

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 13
5. CONNECTIONS
①Audio connection
The camera provides a mono audio input and output. Due to low audio output power, an
amplified speaker is recommended for enhanced sound (Refrain from connecting a headphone
or an earphone directly to the camera).
Mic
Amp Speaker
ETHERNET MICRO SD DC12V
DO DI
1OutOut 1
VIDEO C C In AUDIO
+
Reset
SW1 SW2 SW3
SW5 SW6
N / A N / A
N / A N / A
SW1
SW2
SW3
SW4
SW5
SW6




ETHERNET MICRO SD DC12V
DO DI
1OutOut 1
VIDEO C C In AUDIO
+
Reset
SW1 SW2 SW3
SW5 SW6
N / A N / A
N / A N / A
SW1
SW2
SW3
SW4
SW5
SW6



PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 14
②Sensor (DI) connection
Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor as the
following figures. The interface type can be controlled by web user interface.
Refer to the provided “PixelPro GXi series Web Page User's Manual”for more details.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
Caution
!
Before connecting sensors, check driving voltage and output signal type of the
sensor. Since the connection is different according to sensor type, be careful to
connect the sensor. Do not exceed the maximum input voltage or relay rate.
③Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VDC 50mA
Caution
!
Do not exceed the maximum relay rating.
+5V
DI
COM
DI
COM
+
-
Relay Type
Voltage Type
+
-
Output of
Sensor
Output of
Sensor
Internal
Internal
+
-
DO
COM
Relay Type
Device
Internal

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 15
④Analog Video Out connection
Use a 75 ohm video coaxial cable to connect to a monitor’s analog video input and check the
camera’s connection and its image focus at the installation site. Be sure to press the output
configuration button (PAL/NTSC button) to see the video (Refer to “3. PART NAMES”to check
the location of the PAL/NTSC button). The factory default is ‘no video output’; Press once to
set the video to PAL, and press again to set the video to NTSC. Pressing the button again will go
back to ‘no video output’ mode, disabling the viewing through the analog video connection.
Note
i
Once the PAL/NTSC button is pressed, the video display lasts for 3 minutes
before it goes back to ‘no video output’mode.
⑤LAN connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable (RJ45) to
connect the device to a hub or a router in the network. When the LAN cable is connected, the
orange LED light will become solid and green LED will blink every 250 millisecond. Refer to
“Appendix (B). Power over Ethernet” for more details.
⑥Power Connection
The camera can be powered from either 12VDC or PoE. If the camera is powered via PoE, refer
to “Appendix (B). Power over Ethernet”for more details. To operate your camera using 12VDC,
make sure the polarity is correct before connecting the power cable. Incorrect connection may
cause damages to the device.
Green LED Orange LED
Video
GND
Red
Black
12V
Red
Black

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 16
6. CONFIGURATION
6.1. Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the
device from converting the MAC address’s hexadecimal numbers, which is attached to the
device. Be sure that the device and PC are on a same area network before running the
installation.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.1.1. Generic IP Environment
In case of generic private network environment where IP address 192.168.XXX.XXX are used,
users may view the live streaming images on a web page using the device’s default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal
Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
2. Start the Microsoft® Internet Explorer web browser and enter the address of the device.
3. Web streaming and device configurations are supported through ActiveX program. When the
ActiveX installation window appears, authorize and install the ActiveX.
MAC address = 00-1C-B8-01-23-45 →IP address = 192.168.35.69
Convert the last two sets of hexadecimal numbers to decimal numbers.

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 17
6.1.2. Custom IP Environment
IPAdminTool is a management tool, which automatically scans all of the network products for
users to perform administrative tasks, which includes network configurations, firmware update,
device reboot, and device organizations.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select “IP Address”; IP Setup window appears.
3. In the IP Setup’s window, information under “Local Network information”displays the
user/PC’s network area information. Those information need to be incorporated to the IP
Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP Address, which
are to be the unique numbers for the device. Refer to the image above for the setting
4. Click “Setup”to complete the modification.

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 18
6.2. View video on web page
Type the proper IP address to view the live streaming images through a web browser.
The default username and password is root / pass.
6.2.1. ActiveX Installation
1. When the browser asks to install the AxUMF software, click “Install”to proceed.
2. When Setup installation pop-up window appears, click “Install”to proceed with rest of
installations.
Note
i
Depending on system OS and Internet Explorer version, installation experience
may differ from one another. Figures described above are from Windows 7,
Internet Explorer 9 environment.

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 19
Caution
!
6.2.2. View video using IPAdmin Tool
IPAdminTool automatically searches all activated network encoders and IP cameras and shows
the product name, IP address, MAC address and etc.
1. From the IPAdminTool’s product list, select the device by highlighting it.
2. Right-click the mouse and select “Web view”.
3. The system’s default web browser opens the device’s address.
Whether directly accessing the streaming video through typing IP address on a
web page or taking steps through IPAdminTool, the ActiveX is needed to be
installed for the Microsoft® Internet Explorer to have the complete
configuration privileges.

PixelPro GXi Series ZN-DNT352XE Series Installation Guide
03-2014-B 20
6.3. Reset
1. Press the reset button for 2 seconds while the device is in use.
2. Wait for the system to reboot.
Caution
!
Please do not hold for more than 2 seconds. Otherwise, the camera may be
switched to its Factory Default settings.
6.4. Factory Default
Resetting the device back to the factory default will initialize all parameters including the IP
address back to the factory defaults. To reset back to the factory default:
To proceed back to the Factory Default reset:
1. Press the reset button and hold.
2. Release the button after 10 seconds.
3. Wait for the system to reboot.
Note
i
The factory default settings can be inferred as follows:
IP address: 192.168.xx.yy
Network mask: 255.255.0.0
Gateway: 192.168.0.1
User ID: root
Password: pass