Garden Oasis Steel Round Gazebo User manual

Owner’s Manual
Date of Purchase: _____/ _____/ _____
Steel Round Gazebo
Product Code: D71 M11969
KSN: 03975385-0
UPC Code: 805670021153
See our extensive assortment of outdoor living products
on-line at www.sears.com and www.kmart.com
Made in / Hech en CHINA
Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179

Assembly Instrucon for Round Gazebo
(GFM00330F)
***CAUTION:
The remote control is not water resistant! During severe or
inclement (Rain, Snow, Wet...) weather, you must keep it indoors!

Part List Qty Image Description
Beam
Beam with Screw
Holder
Cambered Rail
Long Slide Bar
Short Slide Bar
Post
Folding Canopy
Canopy Cover
Support Bar
Canopy Cover
Attachment Tube
Solar Panel
Beam Hub
Light Cover
Light
Rail Connect
Post Holder
Base
Canopy Handle
Netting
Canopy Cover
Side Wall
Nut and Washer
Plastic Ring
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
5
1
6
6
6
6
1
1
2
1
1
1
1
6
6
6
1
6
1
6
1
72
1

2
3
4
1
5
6
7
8
9
10
11
12
Descripon
Plasc Washer
for Slide Bars
Screw & Nut
Screw & Nut
Screw
Screw
Screw
Screw
Nut Wrench
Magnec Plate
Allen Wrench
Light Control
with Holder
Slide Bar Holder
Plasc Grove
Countersunk
Screw
Ground Stake
Wrench
Part List Qty Image
W12
1
X
Y1
Z97
Z6
Z12
2
Z
1
Z1
Z2
1
Z
Z6
4
4
12
1
Z
Z
Z
Z
Z
2

Fig 1 Fig 2
Step1:
1. Lay down all 6pcs Cambered Rails (C) in a cycle. Insert all 6pcs Rail Connecters (N) into the end of
Cambered Rails (C), keep screw holes straight, as shown in Fig.1
2. Secure all 6pcs Post Holder (O) to the Cambered Rails (C) with Allen Wrench (Z6)
and M6x15mm Screws (Z), as shown in Fig. 2.
3. Turn over the circle structure as shown in Fig.3. DO NOT PUT ANY WEIGHT OR PRESSURE ON
THE STRUCTURE.
Fig 3
Step 1
C
Z
C
O
C
N
C
N
3

Fig 1
Fig 2
Fig 4 Fig 3
Step2:
1. Connect all 5pcs of Beams (A) and 1pc of Beam with Screw Holder (B) to Beam Hub (K). Use
1pc M6x15 Screw (Z) to secure each beam to Beam Hub (K), as shown in Fig.1 & Fig.2
2. This step requires 2 people to li the Roof structure onto the circle structure. Have one hold
the roof structure and the other person aach the booms of Beams (A) and Beam with
Screw Holder (B) to the top of Post
Holder (O), using M6x45 Screw (Z1). Refer to Fig.3
3. Connect MagnecPlate (Z5) with the inner part of Cambered Rail (C) right below the Beam
with Screw Holder (B) using M6x8 Screws (Z3). Refer to Fig.4
Step 2
AZ
KKZ
B
A
A
B
A
O
BA
O
O
C
3
Z
5Z
1Z
4

Fig 1
Fig 2
Fig 3
Fig 5
Step3:
1. Insert the boom rib (the one without wheel) of the Canopy (G) into the boom of Beam with
Screw Holder (B), as shown in Fig.1
Connect the top rib of the Canopy (G) onto the top of Beam with Screw Holder (B) with M5x15
Screw and Nut (X), as shown in Fig.2
2. Place the ribs with wheels onto the Cambered Rail (C), as Shown in Fig.3 & Fig.4. (Make sure all
the wheels are on the back side of the magnec plate (Z5).
3. Thread the wire of the Canopy (G) through the top of the Beam Hub (K). As shown in Fig.5.
Secure the Canopy (G) and Beam Hub (K) with a Nut and Washer (U), using Nut Wrench (Z) on the top of
the Beam Hub (K) and Wrench (Z12) under the Canopy (G). Tighten them as shown in Fig.6
Step 3
K
G
G
B
G
G
X
B
Fig 4
C
Fig 6
KU
G
4
Z
12Z
5

Fig 1 Fig 2
Step4:
1. With one person holding the Light (M), another person connect the two wires as shown
in Fig.1
2. Secure the Light (M) under the Folding Canopy (G) by inserting 2pcs M6x15 Screws(Z)
through the bracket and into the top of the Light(M). As shown in Fig.2
Step 4
K
GG
Z
M
M
6

Fig 4
Fig 3
I
Z
B
I
Z
A
BZ
A
H
Z
Fig 2
Step5:
1. Insert the 2pcs Canopy Cover Attachment Tube (I) into Canopy Cover (S) as shown in Fig.1.
Attach the Canopy Cover (S) to the Beams (A & B) with 3pcs M6x15 Screws (Z) on each Beam. As
shown in Fig.3 & Fig.4
2. Connect the Canopy Cover Support Bar (H) onto the end of Beam (B) and Beam (A) with
M6x15 Screw (Z). Attach the end of Canopy Cover (S) to the Canopy Cover Support Bar (H) using
the veko on the bottom of the Canopy Cover (S) . As shown in Fig.2
Step 5
IS
I
I
S
Fig 1
7

Fig 4
Fig 3
Fig 2
Fig 1
Step6:
*** Take out Solar Panel (J), Be sure to turn on the Solar Panel (J) (Press the red button) ,
as shown in Fig.1
1. Thread the wire on the Solar Panel (J) into the big hole of the Light Cover (L). Connect
the Solar Panel (J) and Light Cover (L) with 1pc M6x15 (Z). As shown in Fig.2
2. Connect the wire on the Solar Panel (J) and the wire on the Light (M) in the Beam Hub
(K). As shown in Fig.3
3. Lay the Solar Panel (J) and Light Cover (L) onto the top of Beam Hub (K). Keep the
screw holes straight and secure the Light Cover (L) onto the beams with 2pcs M6x15 Screws
(Z). As shown in Fig.4
*** Once the Solar Panel (J) and Light (M) is connected, you can try the remote control.
If the light turns on, then it works. Otherwise, please check the wiring and make sure
the Solar Panel (J) is turned "on".
Step 6
J
ZZ
L
J
L
K
M
G
J
Z
L
8