SUGGESTED SCREEN USAGES (Fig. 18,19,20)
(Fig. 11)
(Fig. 12)
(Fig. 14)
(Fig. 15)
(Fig. 16)
(Fig. 13)
(Fig. 17)
)02.giF()91.giF()81.giF(
4 of 6
(Fig. 21)
(Fig. 22)
(Fig. 23)
(Fig. 24)
(Fig. 25)
5 of 6
TAKE-DOWN INSTRUCTIONS
IMPORTANT: DO NOT USE EXCESSIVE FORCE DURING TAKING-DOWN.
PLEASE REMOVE ANCHORS AND GUY ROPES BEFORE TAKING DOWN.
1. Please reverse the screen assembly procedures
to remove the screen.Warning:to keep the
crotchets on velcro from catching your screen,
please press firmly together the male and female
strips of velcro and form the loop right after undo
the velcro from tubes.(Fig. 21)
2. With the partner, lift two adjacent outer legs slightly,
depress snap button and telescope inner legs up into
outer legs. Undo the velcro straps of the fabric top
from around the roof tubes and cross beams.
Failure to do so may resultin the tear of fabric
during take-down.(Fig. 22)
3. CRITICAL STEP TO AVOID FRAME DAMAGE!
Release sliders at all four corners by gently
depressing the push button and pushing the
sliders down a bit.(Fig. 23)
4. With partner on the opposite side, grasp the upper
portion of outer legs and slightly lift up. Shake the
frame slightly and step towards partner until the
canopy is 3/4 closed. Pleasedo not push too
hard!(Fig. 24)
5. Grasp the adjacent outer legs and push the unit
together until fully closed. Be careful not to pinch
your fingers! Make sure the fabric canopy is
completely dry and then returns your folded pop
up gazebo to the carry bag for storage.(Fig. 25)
5. Engage the slider at each corner by pushing up the slider
with one hand while holding down the top of the leg with
the other hand. Repeat this operation at remaining
corners.(Fig. 7)
6. To secure the fabric top tothe frame, please wrap the velcro
loop straps around roof tubes and cross beams.(Fig. 8)
7. Pull down the Inside valances to cover the beam tubes.
Velcro the adjacent valances together for clean look.(Fig. 9)
8. Lift two adjacent outer legs and pull out inner legs
gently until spring loaded snap button pops in position.
Repeaton the remaining legs. The gazebo offers three
height levels. To adjust, lift the leg up, carefully depress
the snap button at knuckle and slowly pull out the inner
leg until the snap button pops in next position. Repeat
on the other legs.(Fig. 10)
9. Stake down the gazebo by driving the 4 small anchors
through the hole on each base foot. This will keep the leg
from moving sideways in mild weather conditions.(Fig. 11)
10.Measure out from the leg to a proper distance and secure
the four big anchors to ground at 45 degree angle. Tie up
one end of each guy rope totriangular shaped rope holder
located on the outside fabric corners. Tie the other end
of each rope to the anchor on the ground. Make sure
the guy ropes have the proper tension.(Fig. 12)
If you have any questions or comments about this product, please contact us at
Call between 8.30am to 4.30pm P.S.T.(Monday to Friday)
1. Unpack the screen and corner curtain combo kit, locate
the zipper end of the screen panel, position it in the middle
of two legs. Place the combo out around the frame.(Fig. 13)
2. Lift the inside valance, match the combo up toframe. Attach
the combo panels to cross tubes by velcro straps.(Fig. 14)
3. Tuck the upper corner of screen upto the corner of outside
valance. Secure to the upper corner frame with velcro
straps.(Fig. 15)
4. Further secure combo to legs with velcro straps.(Fig. 16)
5. You may zip the screen all around tokeep insects out. Or
leave one side unzipped as entrance, by adjusting the
attachement location of combo panels at cross beams, you
may hold back the combo panels with tiebacks for
drapery look.(Fig. 17)
(Fig. 10)
SCREEN & CORNER CURTAIN ASSEMBLY
THIS GAZEBO MUST BE SECURED TO THE GROUND
WITH ANCHORS AND GUY ROPES.
(Fig. 7)
(Fig. 8)
(Fig. 9)
