Gardeners 8594333 User manual
back
front
V Rev /#
Garden Tip Cart
The Garden Tip Cart is the ideal tool to have when working around your garden or property. Now you can carry heavy loads with
ease, and just tip the cart to empty it. The four hefty wheels are designed to travel on a variety of different terrains, allowing you to
pull it just about anywhere. It has comfortable spring-loaded handle so you won’t have to constantly bend down to pick it up.
Parts List Tools recommended
() Tub mm socket wrench
() Wheels mm wrench or adjustable wrench
() Rear Axle Support mm wrench, socket wrench or box end wrench
() Front Axle Support Slotted screwdriver
() Handle Lock Phillips screwdriver
() Front Frame
() Handle
() loose Bolts with Washers & Nuts
() loose Hex Bolts with Washers & Nuts
Assembly
NOTE: Assembly is easiest with two people. We recommend assembling
the cart outside in a well-ventilated area. Natural rubber tires can emit an
unpleasant, but harmless, odor for a short time until the rubber ages.
Step 1. Lay out all parts on a clean, level surface. Important: Use the Figures
and images to help identify the parts during assembly.
Step 2. Place the Tub upside down on a flat surface. Keep in mind that the straight end is the
front of the Tub and the curved end is the back of the Tub.
Step 3. Line up the holes in the Rear Axle Support with the holes in the back of the
Tub, as shown in Figure . Insert Bolts through the lined up holes. NOTE: Bolt
heads should be on the inside of the Tub, nuts on the outside. Slide a Washer
onto each Bolt and loosely attach the Nuts. Once all Bolts are in place,
tighten them using a mm socket wrench and slotted screwdriver.
Step 4. Line up the holes in
the Handle Lock with the
holes in the front of the Tub
(Figure ). Working from
the inside of the Tub, insert
Bolts through the lined
up holes. Slide a Washer
onto each Bolt and loosely
attach the Nuts. Wait until
all Bolts are in place before
tightening them with a
mm socket wrench and
slotted screwdriver.
over please
Rear Axle
Support
front view
Bolts, Washers
& Nuts
Handle Lock
Figure 1
Phone Orders: 1-800-427-3363 • Customer Service: 1-800-876-5520
Step 5. Take the Front Axle Support and use your
wrenches to tighten the pre-attached nuts and
bolts (Figure ). Tighten them fully, and then
loosen them one half turn for easier steering
movement.
Step 6. Line up the holes in the top of the Front
Axle Support with the holes on the Front Frame
as shown in Figure . Insert Bolts and the Hex
Bolts through the holes in the Front Frame, into
the holes in the Front Axle Support. NOTE: Use
the Hex Bolts on the set of holes closest to each
other (Figure ). Slide a Washer onto each Bolt
and loosely attach the Nuts. Once all Bolts are in
place, go back and tighten them. NOTE: To tighten the Hex Bolts, use the mm socket
wrench and either a mm wrench or an adjustable wrench.
Step 7. Carefully place the Front Frame and attached Front Axle Support onto the bottom
of the Tub (Figure ). Line up the holes in the sides of the Front Frame with the holes in
the sides of the Tub. Working from the inside of the Tub, insert Bolts through both sets of
holes. Slide a Washer onto each Bolt and loosely attach the Nuts. Wait until both Bolts are in
place before tightening them.
Step 8. Remove the pre-attached nuts and washers from the ends of the axles (Figure ).
Examine the Wheels and notice how one side is flatter than the other. With the flat side
facing out, slide the Wheels onto the axles, followed by the washers (Figure ). Screw the
Nuts back into place and tighten them using a mm wrench.
Step 9. Remove the pre-attached long bolt, washer and nut from the end of the Handle
and slide it onto the pipe on the Front Axle Support (Figure ). NOTE: There are two sets
of holes in the end of the Handle, allowing you to position your Handle horizontally (as
shown) or vertically. Line up the chosen set of holes in the Handle with the holes in the
Front Axle Support and slide the long bolt through them (Figure ). Attach the washer and
nut onto the end of the bolt and use a Phillips screwdriver to tighten it. Your assembly is
complete!
To tip the Cart, pull forward on the Handle Lock and lift up (Figure ). Once done, lower the
Tub back into the downward position. Pull forward on the Handle Lock and press down on the
front of the Tub to lock it back into place.
The Garden Tip Cart can carry up to lbs.
For more gardening tools, please visit us at gardeners.com.
Figure 4
Rear Axle
Support
Front Axle
Support
Front
Frame
Bolt, Washer
& Nut
axles
Figure 6
long bolt
washer
& nut
Handle
Front Axle
Support
Figure 5
Wheel (flat side)
nut
washer
Figure 7
Handle
Lock
Figure 2
Front Axle
Support
pre-attached bolts,
washers & nuts
connects
to Handle
Figure 3
Front Frame
Front Axle Support
(upside down)
Bolts, Washers
& Nuts
Hex Bolts,
Washers &
Nuts
Table of contents
Other Gardeners Outdoor Cart manuals
