Garmin STRIKER Vivid 4 User manual

User Manual of Product 1:
Garmin 010-02550-00 Striker Vivid 4cv, Easy-to-Use 4-inch
Color Fishfinder and Sonar Transducer, Vivid Scanning Color
Palettes

STRIKER™VIVID
Owner’s Manual

© 2020 Garmin Ltd. or its subsidiaries
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or
improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to
www.garmin.com for current updates and supplemental information concerning the use of this product.
Garmin®, the Garmin logo, and Ultrascroll® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. ActiveCaptain®, Garmin ClearVü™, Garmin
Quickdraw™, and STRIKER™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.
Wi‑Fi® is a registered mark of Wi-Fi Alliance Corporation.
The BLUETOOTH® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Garmin is under license.

Table of Contents
Introduction..................................... 1
Device Keys............................................. 1
Home Screen...........................................2
Zooming on the STRIKER Vivid 4........... 2
Panning on the STRIKER Vivid 4............ 2
GPS Satellite Signal Acquisition............ 2
Customizing the Chartplotter........... 3
Customizing the Home Screen.............. 3
Combination Pages................................ 3
Creating a New Combination Page
with the STRIKER Vivid 5/7/9............. 3
Creating a New Combination Page
with the STRIKER Vivid 4.................... 4
Customizing a Combination Page..... 4
Adjusting the Backlight.......................... 4
Adjusting the Color Mode.......................4
Setting the Beeper.................................. 4
ActiveCaptain® App......................... 5
ActiveCaptain Roles............................... 5
Getting Started with the ActiveCaptain
App...........................................................5
Enabling Smart Notifications................. 5
Updating Software with the
ActiveCaptain App.................................. 6
Sonar Fishfinder...............................6
Traditional Sonar View........................... 7
Garmin ClearVü Sonar View................... 8
SideVü Sonar View..................................9
Split-Screen Frequency...........................9
Flasher................................................... 10
Split-Zoom View....................................11
Selecting the Transducer Type............ 11
Sonar Frequencies................................ 12
Selecting the Transducer
Frequency.......................................... 12
Creating a Waypoint on the Sonar
Screen Using the Device Keys............. 12
Pausing the Sonar................................ 12
Adjusting the Zoom.............................. 13
Locking the Screen to the Water
Bottom............................................... 13
Sonar Gain............................................. 13
Setting the Gain Automatically........ 13
Setting the Gain Manually................ 13
Adjusting the Range of the Depth
Scale...................................................... 14
Sonar Setup...........................................14
Showing and Adjusting the Depth
Line.................................................... 14
Setting the Scroll Speed................... 14
Setting the Bottom Search Limit...... 14
Sonar Appearance Settings............. 15
Sonar Noise Rejection Settings....... 16
Overlay Number Settings..................17
Garmin Quickdraw Contours
Mapping.........................................17
Mapping a Body of Water Using the
Garmin Quickdraw Contours Feature.. 17
Adding a Label to a Garmin Quickdraw
Contours Map....................................... 18
Deleting Garmin Quickdraw
Contours................................................ 18
Garmin Quickdraw Community............18
Connecting to the Garmin Quickdraw
Community with ActiveCaptain....... 18
Map Settings......................................... 19
Garmin Quickdraw Contours
Settings................................................. 19
Depth Range Shading....................... 20
Navigation with the STRIKER
Vivid.............................................. 20
Searching for a Destination by
Name..................................................... 20
Creating a Waypoint on the Map......... 21
Navigating to a Waypoint..................... 21
Creating and Navigating a Route Using
the Map................................................. 21
Stopping Navigation............................. 21
Waypoints............................................. 21
Marking Your Present Location as a
Waypoint............................................21
Creating a Waypoint at a Different
Location............................................. 21
Marking and Navigating to a Man
Overboard Location.......................... 21
Measuring Distance on the Map...... 22
Viewing a List of all Waypoints........ 22
Editing a Saved Waypoint................. 22
Table of Contents i

Deleting a Waypoint or an MOB....... 22
Deleting All Waypoints......................22
Routes................................................... 22
Creating and Navigating a Route
Using the Map................................... 22
Creating and Saving a Route............ 23
Viewing a List of Routes................... 23
Editing a Saved Route....................... 23
Browsing for and Navigating a Saved
Route..................................................23
Browsing for and Navigating Parallel
to a Saved Route............................... 24
Deleting a Saved Route.................... 24
Deleting All Saved Routes................ 24
Tracks.................................................... 24
Showing Tracks................................ 24
Clearing the Active Track................. 24
Saving the Active Track.................... 25
Viewing a List of Saved Tracks........ 25
Editing a Saved Track....................... 25
Saving a Track as a Route................ 25
Browsing for and Navigating a
Recorded Track................................. 25
Deleting a Saved Track..................... 25
Deleting All Saved Tracks.................25
Retracing the Active Track............... 26
Setting the Color of the Active
Track.................................................. 26
Managing the Track Log Memory
During Recording.............................. 26
Configuring the Recording Interval of
the Track Log.................................... 26
Device Configuration...................... 26
System Settings.................................... 26
System Information.......................... 27
My Vessel Settings............................... 27
Setting the Keel Offset......................28
Setting the Water Temperature
Offset................................................. 28
Setting Alarms...................................... 29
Navigation Alarms............................ 29
System Alarms.................................. 29
Sonar Alarms.....................................29
Unit Settings.......................................... 29
Navigation Settings.............................. 30
Restoring the Factory Default
Settings................................................. 30
Sharing and Managing User Data... 30
Connecting to a Garmin Device to Share
User Data............................................... 30
User Data Sharing Cable Wiring
Diagram............................................. 31
Clearing Saved Data............................. 31
Appendix........................................32
Registering Your Device with the Serial
Number..................................................32
Specifications....................................... 32
Troubleshooting....................................32
My device will not turn on or keeps
turning off.......................................... 32
My device will not acquire GPS
signals............................................... 33
My sonar does not work................... 33
My device is not creating waypoints in
the correct location...........................33
My device does not display the correct
time.................................................... 33
Index..............................................34
ii Table of Contents

Introduction
WARNING
See the Important Safety and Product Information guide in the product box for product warnings and other
important information.
Device Keys
Item Icon Description
Returns to the previous screen.
Returns to the home screen when held.
Scrolls, highlights options, and moves the cursor.
Zooms in and out of a view.
Closes a menu, when applicable.
Opens a menu of options for the page, when applicable.
Turns on and off the device when held.
Performs one or more of these actions when quickly pressed:
• Adjusts the backlight
• Adjusts the color mode
• Enables and disables sonar
Acknowledges messages and selects options.
Saves the present location as a waypoint.
Zooms out of a view. (Not available on all models.)
Zooms in to a view. (Not available on all models.)
NOTICE
Before turning on the device, you must firmly press the connectors into the appropriate holes in the device. If
the cables are not pressed far enough into the device, the device appears to lose power or stop working.
Introduction 1

Home Screen
The fishfinder home screen provides access to all of the features in the fishfinder. The features are dependant
on the accessories you have connected to the fishfinder. You may not have all of the options and features
discussed in this manual.
When viewing another screen, you can return to the home screen by holding . You can customize the layout
of the screens.
Zooming on the STRIKER Vivid 4
You can zoom in and out of the map.
• Select to zoom in.
• Select to zoom out.
Panning on the STRIKER Vivid 4
You can move the sonar views and maps to view an area other than your present location.
1Select or to start panning.
2Use the arrow keys to pan.
TIP: You can select to stop panning.
GPS Satellite Signal Acquisition
When you turn on the fishfinder, the GPS receiver must collect satellite data and establish the current location.
When the fishfinder acquires satellite signals, appears at the top of the Home screen. When the fishfinder
loses satellite signals, disappears and a flashing question mark appears over on the screen.
For more information about GPS, go to www.garmin.com/aboutGPS.
2 Introduction

Customizing the Chartplotter
Customizing the Home Screen
You can add items to and rearrange items on the Home screen.
1From the Home screen, select Customize.
2Select an option:
• To rearrange an item, select Rearrange, select the item to move, and select the new location.
• To add an item to the Home screen, select Add, and select the new item.
• To remove an item you have added to the Home screen, select Remove, and select the item.
• To change the Home screen background image, select Background, and select an image.
Combination Pages
Some pages combine two or more functions on one page. The number of options available for combination
pages depends on the optional devices you have connected to your STRIKER Vivid device. You can edit the
combination pages and create new combination pages.
Creating a New Combination Page with the STRIKER Vivid 5/7/9
You can create a custom screen to suit your needs.
1Select Customize > Add > Add Combo.
2Select a layout.
3Select an area.
4Select a screen.
5Repeat these steps for each area of the page.
6If necessary, select Data (Hidden), and select an option:
• To customize the data shown on the screen, select Overlay Numbers.
• To turn on and off the compass tape data bar, select Compass Tape.
7Select Done when you are done customizing.
8Select Next.
9Enter a name for the page.
TIP: Select to select a letter.
10 Use the arrow keys to resize the windows.
11 Use the arrow keys to select a location on the home screen.
12 Select Done to exit.
Customizing the Chartplotter 3

Creating a New Combination Page with the STRIKER Vivid 4
You can create a custom page to suit your needs.
1Select Customize > Add > Add Combo.
2Select the first function.
3Select the second function.
4Select Split to choose the direction of the split screen (optional).
5Select Next.
6Enter a name for the page.
TIP: Select to select the letter.
7Use the arrow keys to resize the windows.
8Use the arrow keys to select a location on the home screen.
9Select Done to exit.
Customizing a Combination Page
1Open a combination page.
2Select > Configure.
3Select an option:
• To change the name, select Name, and enter a new name.
• To change the arrangement of the information on the screen, select Change Layout, and select a new
layout.
• To change the information shown on the screen, select Change Function, and select new information.
• To resize the information areas shown on the screen, select Resize Combination.
• To customize the data shown on the screen, select Overlay Numbers (Overlay Number Settings,
page 17).
Adjusting the Backlight
1Select Settings > System > Display > Backlight.
2Adjust the backlight.
TIP: From any screen, press repeatedly to scroll through the brightness levels. This can be helpful when
the brightness is so low you cannot see the screen.
Adjusting the Color Mode
1Select Settings > System > Display > Color Mode.
TIP: Select > Color Mode from any screen to access the color settings.
2Select an option.
Setting the Beeper
You can set when the device makes sounds.
1Select Settings > System > Beeper.
2Select an option:
• To have the device beep when you select an item and when an alarm is triggered, select On (Selections
and Alarms).
• To have the device beep only when alarms are triggered, select Alarms Only.
4 Customizing the Chartplotter

ActiveCaptain®App
WARNING
This feature allows users to submit information. Garmin® makes no representations about the accuracy,
completeness, or timeliness of information submitted by users. Any use or reliance on the information
submitted by users is at your own risk.
The ActiveCaptain app provides a connection to your STRIKER Vivid device and the community for a connected
boating experience.
You can use the app to easily and quickly transfer user data, such as waypoints and routes, connect to the
Garmin Quickdraw™ Contours Community, update device software, and plan your trip.
ActiveCaptain Roles
Your level of interaction with the STRIKER Vivid device using the ActiveCaptain app depends on your role.
Feature Owner Guest
Register device to account Yes No
Update software Yes Yes
Automatically transfer Garmin Quickdraw contours you have downloaded or created Yes No
Push smart notifications Yes Yes
Getting Started with the ActiveCaptain App
NOTE: The ActiveCaptain feature is only available on STRIKER Vivid 7 and STRIKER Vivid 9 models, which have
Wi‑Fi® technology.
You can connect a mobile device to the STRIKER Vivid device using the ActiveCaptain app. The app provides a
quick and easy way for you to interact with your chartplotter and complete such tasks as sharing data,
registering, updating the device software, and receiving mobile device notifications.
1From the STRIKER Vivid device, select ActiveCaptain.
2From the ActiveCaptain page, select Wi-Fi Network > Wi-Fi > On.
3Enter a name and password for this network.
4From the application store on your mobile device, install and open the ActiveCaptain app.
5Bring the mobile device within 24 m (80 ft.) of the STRIKER Vivid device.
6From your mobile device settings, open the Wi‑Fi connections page and connect to the Garmin device, using
the name and password you entered in the Garmin device.
Enabling Smart Notifications
WARNING
Do not read or reply to notifications while operating the vessel. Failure to pay attention to the conditions on the
water can result in vessel damage, personal injury, or death.
Before your STRIKER Vivid device can receive notifications, you must connect it to your mobile device and to
the ActiveCaptain app.
1From the STRIKER Vivid device, select ActiveCaptain > Smart Notifications > Enable Notifications.
2Turn on Bluetooth® technology in the mobile device settings.
3Bring the devices within 24 m (80 ft.) of each other.
4From the ActiveCaptain app on the mobile device, select Smart Notifications > Pair with Chartplotter.
5Follow the on-screen instructions to pair the app to the STRIKER Vivid device.
6When prompted, enter the key on your mobile device.
7If necessary, adjust which notifications you receive in your mobile device settings.
ActiveCaptain® App 5

Updating Software with the ActiveCaptain App
If your device has Wi‑Fi technology, you can use the ActiveCaptain app to download and install the latest
software updates for your device.
NOTICE
Software updates may require the app to download large files. Regular data limits or charges from your Internet
service provider apply. Contact your Internet service provider for more information about data limits or charges.
The installation process can take several minutes.
1Connect the mobile device to the STRIKER Vivid device (Getting Started with the ActiveCaptain App, page 5).
2When a software update is available and you have internet access on your mobile device, select Software
Updates > Download.
The ActiveCaptain app downloads the update to the mobile device. When you reconnect the app to the
STRIKER Vivid device, the update is transferred to the device. After the transfer is complete, you are
prompted to install the update.
3When you are prompted by the STRIKER Vivid device, select an option to install the update.
• To update the software immediately, select OK.
• To delay the update, select Cancel. When you are ready to install the update, select ActiveCaptain >
Software Updates > Install Now.
Sonar Fishfinder
For more information about which transducer is best for your needs, go to garmin.com/transducers.
Different sonar views can help you view the fish in the area. The sonar views available vary depending on the
type of transducer and sounder module connected to the chartplotter. For example, you can view certain
Garmin ClearVü™ sonar screens only if you have a compatible Garmin ClearVü transducer connected.
There are four basic styles of sonar views available: a full-screen view, a split-screen view that combines two or
more views, a split-zoom view, and a split-frequency view that displays two different frequencies. You can
customize the settings for each view in the screen. For example, if you are viewing the split-frequency view, you
can separately adjust the gain for each frequency.
6 Sonar Fishfinder

Traditional Sonar View
There are several full-screen views available, depending on the transducer that is connected.
The full-screen Traditional sonar view shows a large image of the sonar readings from a transducer. The range
scale along the right side of the screen shows the depth of detected objects as the screen scrolls from the right
to the left.
Depth information
Suspended targets or fish
Bottom of the body of water
Sonar Fishfinder 7

Garmin ClearVü Sonar View
NOTE: To receive Garmin ClearVü scanning sonar, you need a compatible transducer. For information about
compatible transducers, go to garmin.com/transducers.
Garmin ClearVü high-frequency sonar provides a detailed picture of the fishing environment around the boat in
a detailed representation of structures the boat is passing over.
Traditional transducers emit a conical beam. The Garmin ClearVü scanning sonar technology emits two narrow
beams, similar to the shape of the beam in a copying machine. These beams provide a clearer, picture-like
image of what is beneath the boat.
8 Sonar Fishfinder

SideVü Sonar View
SideVü scanning sonar technology shows you a picture of what lies to the sides of the boat. You can use this
as a search tool to find structures and fish.
Left side of the boat
Right side of the boat
The transducer on your vessel
Logs
Old tires
Trees
Water between the vessel and the bottom
Distance from the side of the boat
Split-Screen Frequency
You can view two frequencies from the split frequency screen.
Sonar Fishfinder 9

Flasher
The flasher shows sonar information on a circular depth scale, indicating what is beneath your boat. It is
organized as a ring that starts at the top and progresses clockwise. Depth is indicated by the scale inside the
ring. Sonar information flashes on the ring when it is received at the depth indicated. The colors indicate
different strengths of the sonar return.
Select Flasher.
Depth at your present location
Depth scale
10 Sonar Fishfinder

Split-Zoom View
On the split-zoom page, you can see a full-view graph of sonar readings on the right side of the screen, and a
magnified portion of that graph on the left side of the screen.
From a sonar screen, select > Zoom > Split Zoom.
Zoomed depth scale
Zoom window
Depth range
Selecting the Transducer Type
If you are connecting a transducer that was not included with the device, you may need to set the transducer
type to make the sonar function properly. Before connecting the transducer, you should select the transducer
type. The transducer name should be listed on the label on the transducer cable, near the connector.
This device is compatible with a range of accessory transducers, including Garmin ClearVü transducers, which
are available at garmin.com/transducers.
1Select Settings > My Vessel > Transducer Type.
2Select an option:
• If you have a 200/77 kHz, dual-beam transducer, select Dual Beam (200/77 kHz).
• If you have a 200/50 kHz, dual-frequency transducer, select Dual Frequency (200/50 kHz).
• If you have another type of transducer, select it from the list.
Sonar Fishfinder 11

Sonar Frequencies
NOTE: The frequencies available depend on the chartplotter, sounder modules, and transducer being used.
Adjusting the frequency helps adapt the sonar for your particular goals and the present depth of the water.
Higher frequencies use narrow beam widths, and are better for high-speed operation and rough sea conditions.
Bottom definition and thermocline definition can be better when using a higher frequency.
Lower frequencies use wider beam widths, which can let the fisherman see more targets, but could also
generate more surface noise and reduce bottom signal continuity during rough sea conditions. Wider beam
widths generate larger arches for fish target returns, making them ideal for locating fish. Wider beam widths
also perform better in deep water, because the lower frequency has better deep water penetration.
CHIRP frequencies allow you to sweep each pulse through a range of frequencies, resulting in better target
separation in deep water. CHIRP can be used to distinctly identify targets, like individual fish in a school, and for
deep water applications. CHIRP generally performs better than single frequency applications. Because some
fish targets may show up better using a fixed frequency, you should consider your goals and water conditions
when using CHIRP frequencies.
Some sonar black boxes and transducers also provide the ability to customize preset frequencies for each
transducer element, which enables you to change the frequency quickly using the presets as the water and your
goals change.
Viewing two frequencies concurrently using the split-frequency view allows you to see deeper with the lower
frequency return and, at the same time, see more detail from the higher frequency return.
Selecting the Transducer Frequency
NOTE: You cannot adjust the frequency for all sonar views and transducers.
You can select which frequencies appear on the sonar screen.
NOTICE
Always be aware of local regulations on sonar frequencies. For example, to protect orca whale pods, you might
be prohibited from using frequencies between 50 to 80 khz with in ½ mile of an orca whale pod. It is your
responsibility to use the device in compliance with all applicable laws and ordinances.
1From a sonar view, select > Frequency.
2Select a frequency suited to your needs and water depth.
For more information on frequencies, see Sonar Frequencies, page 12.
Creating a Waypoint on the Sonar Screen Using the Device Keys
1From a sonar view, use the arrow keys to select a location to save.
2Select .
3If necessary, edit the waypoint information.
Pausing the Sonar
Not all options are available on all models.
Select an option:
• From the Traditional or ClearVü sonar screen, select or .
• From the SideVü sonar screen, select or .
12 Sonar Fishfinder

Adjusting the Zoom
You can adjust the zoom manually by specifying the span and a fixed starting depth. For example, when the
depth is 15 m and the starting depth is 5 m, the device displays a magnified area from 5 to 20 m deep.
You also can allow the device to adjust the zoom automatically by specifying a span. The device calculates the
zoom area from the bottom of the water. For example, if you select a span of 10 m, the device displays an
magnified area from the bottom of the water to 10 m above the bottom.
1From a sonar screen, select > Zoom.
2Select an option:
• Select Bottom Lock to lock the screen to the water bottom.
• Select Manual to manually set the zoom.
• Select Auto to automatically set the zoom.
• Select Split Zoom to turn on the split-zoom view.
Locking the Screen to the Water Bottom
You can lock the screen to the water bottom. For example, if you select a span of 20 meters, the device shows
an area from the water bottom to 20 meters above the bottom. The span appears on the right side.
1From a sonar view, select > Zoom > Bottom Lock.
2Select a span.
Sonar Gain
The gain setting controls the sensitivity of the sonar receiver to compensate for water depth and water clarity.
Increasing the gain shows more detail, and decreasing the gain reduces screen clutter.
NOTE: Setting the gain on one sonar view applies the setting to all the views.
Setting the Gain Automatically
NOTE: To set the gain on the split-frequency screen, you must set each frequency separately.
1Select > Gain.
2Select Enable Auto Gain, if applicable.
3Select an option:
• To display higher-sensitivity, weaker sonar returns with more noise automatically, select Auto High.
• To display medium-sensitivity sonar returns with moderate noise automatically, select Auto Med.
• To display lower-sensitivity sonar returns with less noise automatically, select Auto Low.
Setting the Gain Manually
1From a sonar screen, select > Gain.
2Select or until you begin to see noise in the water portion of the screen.
3Select or to decrease the gain.
Sonar Fishfinder 13

Adjusting the Range of the Depth Scale
You can adjust the range of the depth scale that appears on the right side of the screen. Automatic ranging
keeps the bottom within the lower third of the sonar screen, and can be useful for tracking the bottom where
there are slow or moderate terrain changes.
When the depth changes dramatically, like a drop off or cliff, manually adjusting the range allows a view of a
specified depth range. The bottom is shown on the screen as long as the bottom is anywhere within the manual
range established.
1From a sonar screen, select > Range.
2Select an option:
• To allow the device to adjust the range automatically based on the depth, select Auto.
• To increase the range manually, select or .
• To decrease the range manually, select or .
NOTE: From a sonar screen, select and to quickly manually adjust the range.
Setting the range on one screen applies that setting to all screens, except the SideVü screen.
Sonar Setup
Showing and Adjusting the Depth Line
You can show and adjust a horizontal line on a sonar screen. The depth of the line is indicated on the right side
of the screen.
NOTE: Showing a depth line on one screen displays the depth line on all of the screens.
1From a sonar screen, select > Sonar Setup > Depth Line.
2Select .
3To adjust the Depth Line, select or .
Setting the Scroll Speed
You can set the rate at which the sonar image moves across the screen. A higher scroll speed shows more
detail, especially while moving or trolling. A lower scroll speed displays sonar information on the screen longer.
Setting the scroll speed on one sonar view applies to all the sonar views.
1From a sonar view, select > Sonar Setup > Scroll Speed.
2Select an option:
• To adjust the scroll speed automatically using speed-over-ground, select Auto.
The Auto setting selects a scroll rate to match the boat speed, so targets in the water are drawn with the
correct aspect ratio and appear less distorted. When viewing Garmin ClearVü or SideVü sonar views, it is
recommend to use the Auto setting.
• To use a very fast scroll speed, select Ultrascroll®.
The Ultrascroll option quickly scrolls new sonar data, but with a reduced image quality. For most
situations, the Fast option provides a good balance between a quickly scrolling image and targets that
are less distorted.
Setting the Bottom Search Limit
You can set a maximum depth at which the auto range feature searches for the bottom. A lower limit acquires
data about the bottom faster than a higher limit.
1From a sonar screen, select > Sonar Setup > Bottom Search Limit.
2Select a range.
14 Sonar Fishfinder

Sonar Appearance Settings
From a sonar view, select > Sonar Setup > Appearance.
Color Scheme: Sets the color scheme.
Edge: Highlights the strongest signal from the bottom to help define the hardness or softness of the signal.
A-Scope: Displays a vertical flasher along the right side of the screen that shows instantaneously the range to
targets along a scale.
Fish Symbols: Sets how the sonar interprets suspended targets.
Turning on the A-Scope
The a-scope is a vertical flasher along the right side of the full-screen sonar view. This feature expands the
most recently received sonar data so that it is easier to see. It can also be helpful for detecting fish that are
close to the bottom.
NOTE: This feature is not available on all sonar screens.
From the full screen page, select > Sonar Setup > Appearance > A-Scope.
A-Scope
Diameter of the sonar cone at the present depth
Configuring the Appearance of Suspended Targets
NOTE: Configuring the appearance of suspended targets on one screen applies that setting to all screens.
NOTE: This feature is not available on all sonar views.
Shows suspended targets as symbols.
Shows suspended targets as symbols with target depth information.
Shows suspended targets as symbols with background sonar information.
Shows suspended targets as symbols with background sonar information and target depth informa
tion.
1From a sonar screen, select > Sonar Setup > Appearance > Fish Symbols.
2Select an option.
Sonar Fishfinder 15