GarrettCom Magnum CSG14 User manual

www GarrettCom com .. www GarrettCom com ..
Corporate Headquarters
GarrettCom, Inc.
47823 Westinghouse Drive
Fremont, CA 94539-7437
Phone [phone]
Fax [phone]
Website: http://www.GarrettCom.com
Email: [email protected]
Magnum CSG14 Gigabit Converter Switches
Installation and User Guide

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
i
www GarrettCom com ..
Magnum™CSG14 Series Gigabit Converter Switch
Installation and User Guide
Part #: 84-00102Z Rev. A
Trademarks
GarrettCom, Magnum, Link-Loss-Learn, S-Ring, Convenient Switch, Converter
Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc.
Ethernet is a trademark of Xerox Corporation
NEBS is a trademark of Telcordia Technologies
UL is a registered trademark of Underwriters Laboratories

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
ii
www GarrettCom com ..
Important: The Magnum CSG14 Series 10/100/1000 Mb/s Converter
Switches contain no user serviceable parts. Attempted service by unauthorized
personnel shall render all warranties null and void. If problems are
experienced with Magnum CSG14 10/100/1000 Mb/s Converter Switch
products, consult Section 5, Troubleshooting, of this User Guide.
Copyright ©2008 GarrettCom, Inc. All rights reserved. No part of this publication may
be reproduced without prior written permission from GarrettCom, Inc.
Printed in the United States of America

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
iii
www GarrettCom com ..
Federal Communications Commission
Radio Frequency Interference Statement
This equipment generates, uses and can radiate frequency energy and if not
installed and used properly, that is in strict accordance with the manufacturer's
instructions, may cause interference to radio communication. It has been tested and
found to comply with the limits for a Class A computing device in accordance with the
specifications in Subpart J of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference, in which case the user, at his/her own expense, will be required to take
whatever measures may be required to correct the interference.

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
iv
www GarrettCom com ..
Contacting GarrettCom, Inc
Please use the mailing address, phone and fax numbers and email address listed below:
GarrettCom, Inc.
47823 Westinghouse Drive
Fremont, CA 94539
Phone [phone]
Fax [phone]
Website: http://www.GarrettCom.com
Email: [email protected]

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
v
www GarrettCom com ..
TABLE OF CONTENTS Page
1.0 SPECIFICATIONS ............................................................................... 1
1.1 Technical Specifications...................................................................... 1
1.2 Summary of models and descriptions:............................................... 11
2.0 INTRODUCTION ............................................................................... 14
2.1 Inspecting the Package and the Product............................................. 14
2.2 Product Description ........................................................................... 15
2.3 Frame Buffering and Latency............................................................ 22
2.4 Features and Benefits......................................................................... 26
2.5 Applications for CSG14 Series Converter Switches.......................... 29
3.0 INSTALLATION................................................................................. 37
3.1 Locating the Converter Switch Unit .................................................. 37
3.2 MC14-TRAY for Rack Mounting of CSG14 Series Switches ......... 39
3.3 MC14-TR+PS9 and X2 for Rack Mounting Media Converters........ 40
3.4 DIN-Rail mounting option................................................................. 42
3.5 Power Requirements, CSG14 Series Switches .................................. 43

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
v
www GarrettCom com ..
3.6 Powering the CSG14H and CSG14P (DC internal) .......................... 45
3.7 CSG14H and P Series , DC-powered, Installation............................. 47
3.8 Connecting Ethernet Media ............................................................... 48
3.8.1 Connecting Twisted Pair............................................................ 50
3.8.2 Connecting Fiber Optic LC-type, “Small Form factor (SFF)”... 51
3.8.3 Connecting Fiber Optic SC-type, "Snap-In".............................. 51
3.8.4 Connecting Single-Mode Fiber Optic........................................ 52
3.8.5 Power Budget Calculations for CSG14 Series, Fiber Media..... 52
3.8.6 Connections to NICs which support Auto-Neg RJ-45 ports...... 55
4.0 OPERATION....................................................................................... 56
4.1 Triple-Speed Functionality, and Switching ....................................... 56
4.2 Auto-cross (MDIX), Auto-negotiation and Speed-sensing................ 58
4.3 Dual LEDs, Front-panel and Side-panel............................................ 60
5.0 TROUBLESHOOTING...................................................................... 61
5.1 Before Calling for Assistance............................................................ 62
5.2 When Calling for Assistance ............................................................. 64
5.3 Return Material Authorization (RMA) Procedure............................. 65

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
vi
www GarrettCom com ..
5.4 Shipping and Packaging Information................................................. 67
APPENDIX A: WARRANTY INFORMATION......................................... 69
Revisions
Rev A 05/08: Initial release of this user manual for CSG14 Converter Switches
GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or
model offerings without notice.

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
1
www GarrettCom com ..
1.0 SPECIFICATIONS
1.1 Technical Specifications
Ports Performance
Data Rate: 10Mbps, 100Mbps, 1000Mbps
Network Standards
1000Mb: Ethernet IEEE 802.3ab and 802.3z
1000Base-T, -SX, -LX and -ZX
100Mb: Ethernet IEEE 802.3u, 100BASE-TX, 100BASE-FX
10 Mb: Ethernet IEEE 802.3, 10BASE-T
Auto-sensing for speed: IEEE 802.3z
Packet-Processing Between Domains
Filter and Forward Rate from 1000Mbps ports: 1,488,000 pps max.
Filter and Forward Rate from 100Mbps ports: 148,800 pps max.
Filtering and Forwarding Rate from 10 Mbps ports: 14,880 pps max.
Processing type: Store and Forward, non-blocking
Auto-learning: 1K-address table
Address buffer age-out time: 300 sec.

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
2
www GarrettCom com ..
Packet buffers memory: 64KB, dynamically shared on all domains
Latency (not including packet time): 100 to 10 Mbps: 5μs
10 to 100Mbps: 15μs
Path Delay Value: 50 BT on all ports
Maximum Ethernet Segment (or Domain) Lengths
10BASE-T (Unshielded twisted pair) 100 m (328 ft)
10BASE-FL, Fiber optic 2 km (6,562 ft)
10BASE-FL, Single-mode Fiber optic 10 km (32,810ft)
100BASE-TX (CAT 5 UTP) 100 m (328 ft)
100BASE-FX, half-duplex: (multi-mode) 412 m (1350 ft)
100BASE-FX, full duplex: (multi-mode) 2 km (6,562 ft)
100BASE-FX, half-duplex: (single-mode) 412 m (1350 ft)
100BASE-FX, full duplex: (single-mode) 20 km (65,620 ft)
100BASE-FX, full duplex: (single-mode, long reach) 40 km (131,240 ft)
1000BASE-T (CAT5E OR HIGHER recommended) 100 m (328 ft)
1000BASE-SX, full duplex, multi-mode (62.5um) 220 m (722 ft)
1000BASE-SX, full duplex, multi-mode (50um) 550 m (1804 ft)
1000BASE-LX, full duplex, single-mode (9um) 5 km (16404 ft)

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
3
www GarrettCom com ..
1000BASE-ZX, full duplex, single-mode (9um) >70 km (229,659 ft)
Operating Environment
CSG14H: -13ºF to 140ºF (-25ºC to 60ºC) Long term per agency tests (UL).
-40ºF to 149ºF (-40ºC to 85ºC) Short term per IEC Type tests
CSG14P: -40ºF to 167ºF (-40ºC to 75ºC) Long term per agency tests (UL)
-40ºF to 149ºF (-40ºC to 85ºC) Short term per IEC Type tests
Storage Temperature,
All models: -40ºF to 212ºF (-40ºC to 100ºC)
Cold Start:
CSG14H to -20ºC
CSG14P to -40ºC
Ambient Relative Humidity: 5% to 95% (non-condensing)
Altitude (All models): -200 to 50000ft. (-60 – 15,000 m)
Conformal Coating (optional) for humidity protection

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
4
www GarrettCom com ..
Note: CSG14 models are designed for NEBS compliance, including, vibration, shock and
altitude.
Packaging:
Enclosure: Rugged sheet metal (Steel).
Dimensions of the Switch unit:
3.5 in H x 3.0 in W x 1.0 in D (8.9 cm x 7.6 cm x 2.5 cm)
Weight: all models: 4.6 oz. (130g);
Power supply, –Hd, and Hi: 5.8 oz (165g)
–Pd, and -Pi: 7.9 oz (225g)
Cooling Method:
Convection on the CSG14 Series models. The hardened (H) factory floor and premium (P)
temperature un-controlled location models have closed cases to withstand dirt and use
special thermal techniques to transfer heat to the outside of the case for cooling.

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
5
www GarrettCom com ..
POWER SUPPLY
These products are intended to be supplied by a Listed, Direct Plug-In power unit, marked
“Class 2”, or a Listed ITE Power Supply, marked “LPS”, which has suitably rated output
voltage (i.e. 9vdc, 12vdc, 24vdc, 48vdc), and suitably rated output current (i.e. 100mA to
500mA). When connected to a 48 V centralized dc source these products shall be provided
with a Listed 5A DC fuses in the supply circuit.
AC POWER SUPPLY (using an external power adapter):
All models have a (8-15) VDC output with 6ft long cord and a 2.5mm center +ve jack. The
power supplies are temperature rated to match the Converter Switch ratings.
Factory Floor (H) Ratings (-25 to 60°C)
North America (-Hd) models. Hardened, factory floor temperature rated. Input: 6ft AC
power cord to IEC 320 connector on the 100-240vac 47-63Hz external power adapter.
Output: 12vdc, 1.25Amps

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
6
www GarrettCom com ..
International (-Hi) models. Factory floor temperature rated. Input: IEC 320 connector on
the 100-240vac 47-63Hz external power adapter. Requires a user supplied power cord
Output: 12vdc, 1.25Amps.
Temperature un-controlled Premium (P) Ratings (-40 to 75°C)
North America (-Pd) models. Outdoor temperature rated. Input: 6ft AC power cord to IEC
320 connector on the100-240vac 47-63Hz external power
adapters.
Output: 12vdc, 2Amps.
International (-Pi) models. Outdoor temperature rated.
Input: IEC 320 connector on the 100-240vac 47-63Hz
external power adapter. Requires a user supplied power cord.
Output: 12vdc, 2Amps.
Direct DC POWER SUPPLY: built-in terminal block
for +, -, ground along with 12VDC jack
12V DC internal (range of 8.0 to 15V DC).

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
7
www GarrettCom com ..
24V DC internal (range of 18 to 36V DC).
-48V DC internal (range of 36 to 60V DC), -, ground.
Power Consumption: See Section 3.6.
Note 1: the 8-15V DC jack can be used for dual source DC input using an AC adapter and
the DC terminal block. Power supply protection is provided by internal diodes.
Note 2: The Direct DC power floats. The user may ground either “+” or “-” if desired.

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
8
www GarrettCom com ..
Port Connectors:
Two RJ-45 Ports: support 10/100/1000Mbps with auto cross (MDIX).
They are shielded 8-pin female connectors for shielded (STP) and unshielded
(UTP) Cat 3, 4, 5 cables.
One Fiber optic port: The CSG14 series is 1000Base-SX / -LX / -ZX with a
“fiber flavor” choice of multimode SC or SLC connectors
Switches
Fiber port default is FDX (Full-Duplex)
RJ45’s are triple-speed auto-negotiating

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
9
www GarrettCom com ..
LED Indicators (Two sets) top-front and end with ports
Top-Front:
POWER: Steady ON when power applied
Gb per RJ45 port: Steady ON for 1000Mbps; OFF for 100Mbps or 10Mb speed
LK/ACT per port: Steady ON for LINK (LK) with no traffic, BLINKING for Activity
End with Ports:
POWER: Steady ON when power applied
10/100/1000Mb per port: Steady ON for 100Mb, OFF for 10Mb,
BLINKING for 1000Mb
Fiber port: LK/ACT: Steady ON for Link with no traffic, BLINKING for Activity
Mounting options
Metal mounting clips for panel mounting: included
DIN-Rail mounting option: Model # DIN-RAIL MC2 (see Section 3.4)
Rack-mount option: MC14-TRAY, see http://www.garrettcom.com/mc_tray.htm
Mean Time Between Failure (MTBF)– over15 years, Telcordia (Bellcore) Method

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
10
www GarrettCom com ..
Agency Approvals and Standards Compliance:
UL Listed (UL 60950), cUL, CE, Emissions meets FCC Part 15 Class A.
NEBS L3 and ETSI compliant.
P model: IEEE P1613 Env. Std for Electric Power Substations
P model: NEMA TS-2 and TEES for traffic control equipment
P model: designed for UL 2043 above-the-ceiling installation
IEC61850 EMC and Operating Conditions Class C Power Substations
Warranty: Three years, return to factory Made in USA

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
11
www GarrettCom com ..
1.2 Summary of models and descriptions:
CSG14H (Hardened Model) for 1000Mb fiber
CSG14H-ff-Hd, Hi = Hardened (H), two 10/100/1000Mb RJ-45+ one 1000Mb Fiber port for
factory floor (-25 to 60C) using a direct DC ( 8-15VDC) and/or external
AC hardened power supply (included).
CSG14H-ff-12VDC = Same as CSG14H model,
except AC hardened power supply is not included
CSG14H-ff-24VDC = Same as CSG14H-12VDC model,
except 24VDC power input replaces 12VDC.
CSG14HR-ff-24VDC = Same as CSG14H-24VDC model,
but includes DIN-RAIL-MC2 mounting option.
CSG14H-ff-48VDC = Same as CSG14H-24VDC model,
except -48VDC power input replaces 24VDC

CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08)
12
www GarrettCom com ..
CSG14P (Premium Model) for 1000Mb fiber
CSG14P-ff-Pd, Pi = Premium (P), two 10/100/1000Mb RJ-45+ one 1000Mb Fiber port for un-
controlled(outdoor) (-40 to 75C) using direct DC (8-15VDC) and/or
external AC premium power supply (included).
CSG14P-ff-12VDC = Same as CSG14P-Pd, Pi, except AC Premium Power Supply is not
included.
CSG14P-ff-24VDC = Same as CSG14P-12VDC model,
except 24VDC power input replaces 12VDC.
CSG14PR-ff-24VDC = Same as CSG14P-24VDC model,
but includes DIN-RAIL-MC2 mounting option.
CSG14P-ff-48VDC = Same as CSG14P-24VDC model, except -48VDC input replaces 24VDC.
Fiber Port Connectors:
The “ff” field is for selection of the desired “fiber flavor” as listed below.
“SX” = 1000Base-SX-SC: 850nm multi-mode fiber optic with SC type connector, 550 m.
“ESX”= 1000Base-SX Extended: 1310nm multi-mode fiber optic with SC type connector, 2 km
“LX10”= 1000Base-LX-SLC: 1310nm multi-mode fiber optic with LC type connector, 10 km