Black Box LIE1014A User manual

STEP X - Name of Step
9
24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM
LIE1014A, LIE1080A , LIE1082A
INDUSTRIAL
POE SWITCH
QUICK START GUIDE

STEP 1 - Hardware Description
LI E1014A
TABLE 1. COMPONENTS
COMPONENT LIE1014A LI E1080A L IE1082A
RJ-45 PoE ports 8 4 4
RJ-45 ports None 4 2
SFP cages 4 None 2
P1 LED 1 1 1
P2 LED 1 1 1
ALM LED 1 1 1
Ethernet Port Link LED 8 8 6
Ethernet Port Speed LED 8 8 6
SFP Port Link LED 4 None 2
SFP Port Speed LED 4 None 2
LIE1082A
LI E1080A

STEP 2 - What's Included
WHAT'S INCLUDED
• (1) INDUSTRIAL POE MANAGED GIGABIT
ETHERNET SWITCH
• (2) WALLMOUNT PLATES
• (1) DIN RAIL CLIP
• (1) DC POWER TERMINAL BLOCK
• RJ-45 PORT DUST COVERS
• SFP PORT DUST COVERS
• THIS QUICK START GUIDE
TABLE 2. LED STATUS INDICATORS
LED NAME STATUS DESCRIPTION
PoE ON Green Port is using power over Ethernet
P1/P2 ON Green P1/P2 power line has power
OFF P1/P2 power line is disconnected or does not have power
Alarm ON Red Ethernet link fails, alarm or power failure alarm occurs
OFF No Ethernet link fails and no power failure alarm
Copper port Link/Act
ON Green Ethernet link up but no traffic is detected
Flashing Green Ethernet link up and traffic is detected
OFF Ethernet link down
Copper port Speed ON Yellow A 1000-Mbps connection is detected
OFF No 1000-Mbps link, a 10-Mbps or 100-Mbps connection is detected
SFP port Link/Act ON Green Ethernet link up
OFF Ethernet link down
SFP port Speed ON Yellow SFP port speed 1000-Mbps connection is detected
OFF No link or an SFP port speed 100-Mbps connection is detected

STEP 3A - Install on DIN Rail
INSTALL THE UNIT ON A DIN RAIL
1. Attach the screws to the DIN clip.
2. Hook the unit onto the DIN rail.
3. Push the bottom of the unit towards the DIN
rail until it locks into place.
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+

STEP 3B - Mount on a Wall
INSTALL THE UNIT ON A WALL
1. Attach the screws to the wallmount brackets.
2. Using M4 screws, attach the unit and bracket
assembly to the wall.
7
5
8
6
4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
P1 P2
POE
ALM
3
9 10
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
11 12
13 14
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1
1
2
3
4
5
6
7
8
1

STEP 4A - Connect the RJ-45 Ethernet Interface
CONNECT THE SWITCH TO PC OR DEVICE
1. To connect the switch to a PC, use a straight-
through Ethernet or crossover cable.
2. To connect the switch to an Ethernet device,
use unshielded twisted-pair (UTP) or shielded
twisted-pair (STP) Ethernet cables.
NOTE: The pin assignments of the RJ-45
connector are shown in the diagram at right
and the table below.
TABLE 3. RJ-45 CONNECTOR PINOUT
PIN REGULAR PORTS POE ASSIGNMENT
1Input Receive Data + Positive VPort
2Input Receive Data - Positive VPort
3Output Transmit Data + Negative VPort
4Not connected Not connected
5Not connected Not connected
6Output Transmit Data - Negative VPort
7Not connected Not connected
8Not connected Not connected
8 7 6 5 4 3 2 1

STEP 4B - Connect the Fiber SFP Ethernet Interface
100/1000BASE-FX CONNECTIONS
For both 100/1000 Mbps fiber speed
connections, the SFP slots are available.
The SFP slot accepts the SFP transceivers
shown in the table below.
DANGER! Never look directly at optical
connectors that might be emitting optical
energy. YOUR EYES MIGHT BE DAMAGED!
TABLE 4. COMPATIBLE SFPS
PART NUMBER DESCRIPTION
LFP411 SFP/1250 Extended Diagnostics, LC multimode, 850 nm, 550 m
LFP412 SFP/1250 Extended Diagnostics, LC multimode, 1310 nm, 2 km
LFP413 SFP/1250 Extended Diagnostics, LC single-mode, 1310 nm, 10 km
LFP414 SFP/1250 Extended Diagnostics, LC single-mode, 1310 nm, 40 km
LFP401 SFP/155 Extended Diagnostics, LC multimode, 850 nm, 2 km
LFP403 SFP/155 Extended Diagnostics, LC single-mode, 1310 nm, 30 km
LFP404 SFP/155 Extended Diagnostics, LC single-mode, 1310 nm, 60 km
LFP402 SFP/155 Extended Diagnostics, LC multimode, 1310 nm, 2 km
LFP418 SFP/1250 Extended Diagnostics, LC single-mode, 1550 nm, 80 km
LFP420 Simplex SFP/1250, Extended Diagnostics, single-mode, 1550 nm TX, 1310 nm RX

STEP 5 - Connect the Power
ALARM RELAY AND GROUND
The alarm relay output contacts are in the
middle of the DC terminal block connector
as shown in the diagram below.
The alarm relay out is “Normal Open” and will
close when it detects a power or Ethernet link
failure.
The relay has a current carrying capacity
of 0.5 A at 24 VDC.
CONNECTING POWER TERMINAL BLOCK
The switch can be powered from two DC power
supplies (input range 12 VDC to 58 VDC).
1. Insert the positive and negative wires into
the V+ and V- contacts on the terminal block.
2. Tighten the wire clamp screws to prevent
the wires from becoming loose.
PWR1
CONSOLE RESET
+ – – +
+
ALM PWR2
12–48 VD C POWER INPU T
GROUND

1
1
2
3 (RD)
4 (TD)
5
6 (DGND)
7
8
6
7
4
8
9
3
TD
2
RD
5
DGND
STEP 6 - Connect the Console Port
CONSOLE CONNECTION
Use the console port to manage the switch
locally via a terminal emulator or a computer
with terminal emulation software.
Connect the switch's DB9 connector to a
computer's COM port with the following
properties:
• Baud rate: 115200 bps
• 8 data bits
• 1 stop bit
• No Priority
• No Flow Control
To connect the host PC to the console port,
you need an RJ-45 male to RS-232 DB9 female
connector cable.
1. Connect the RJ-45 end of the cable to the
switch‘s console port.
2. Connect the DB9 end of the cable to the
PC's COM port.

STEP 7 - Connect and Login to the Switch
CONNECT TO THE ETHERNET PORT
1. Connect to the Ethernet port of the
managed switch.
Factory Default IP: 192.0.2.1
2. Log in with the default username
and password:
Username: admin
Password: (blank) (Just press the Enter key.)
OPTIONAL: DOWNLOAD USER MANUAL
For product specifications and regulatory
information, refer to the User Manual. You can
download this document from our web site.
1. Go to www.blackbox.com
2. Enter the part number (LIG1014A, LIG1080A
or LIG1082A) in the search box.
3. Click on the product in the “Product
Results” page.
4. Click on the “Support” tab on the product page,
and select the document you wish to download.
If you have any trouble accessing the Black Box
site to download the manual, you can contact
our Technical Support at 877-877-2269
or [e-mail].