Gatekeeper NetDX 2.7 User manual

Table of Contents
What is NetDX Access Control ? ..................................................................................... 3
A Simple System Set Up ................................................................................................. 4
Door Controllers ........................................................................................................... 5
Wired IP access control .............................................................................................. 5
Readers installation ................................................................................................. 10

What is NetDX Access Control ?
NetDX is GateKeeper's User friendly and flexible networked access
control system , which is managed from a central pc.
NetDX access control is really easy to install and designed to make
management of any building very simple.
NetDX offers a range of ip, battery power, wireless or wired door
controllers to suit any site requirement, making installer's lives
easier.
Easy to quote:
Build your NetDX access control system one door at a time. *
A range of NetDX products to suit any site requirement*
Scalable System –add doors when the budget is available*
Easy to install:
Plug and play solution that connect directly to the network*
*Mix and match NetDX products –they all designed to work together
Clear Instructions and colour coded wiring label.*
deal with:Easy to
Industry leading technical support
Free Software upgrades and no multiple license fees

A Simple System Set Up
NetDX Designed with simplicity in mind and is easily scalable.
Gatekeeper's two door controller philosophy means you only quote
for doors that require access. You can build your NetDX system two
door at time using the following components.
Components:
*1x Gatekeeper Software –Download from website
(www.accessgk.com)
*1x NetDX controller
2x Reader / Keypad*
2x Exit Button*
2x Door release lock*

Door Controllers
All GateKeeper door controllers can be used alongside each other,
making it easy for installers to find the best solution for each
individual site.
Wired IP access control
Allow TCP/IP technology with direct connection to the IP network.
*USB Directly from NetDX RS-485 to PC .
) to download the latestwww.accessgk.comPlease use our website (
driver for Driver RS-485 .
*Notice:
After USB connected to PC press Windows Key + R and enter
devmgmt.msc for checking which port the pc using , for example
com 10 in pic below :

*Connect the Ethernet cable from latronix unit to
the Ethernet port ( PC or switch)
Notice
For the configuration of the latrnoix unit you can use free program by
)www.accessgk.comis a download in( thereCPR Mangerthe name:
After installing the CPR Manger. Press and all the
Latronix units that connected to the pc or switch will appear below:
press Launch web interface to device > Login screen will appear,
Press Enter key.

Press Network tab and config the Latronix unit for the pc or Switch,
Press OK.
Go to Connection TAB and look for Local Port ( Default is 10001)
After that step Press OK and press Apply Setting TAB .
Wait a while for applying is done and close the web.
You finish configure the unit .
For using TCP/IP in Gatekeeper software you can check Manual Guide for
Gatekeeper.

*Connect the Ethernet cable from Tibbo unit to
the Ethernet port ( PC or Switch)
For Configuration Tibbo you should Download Tibbo Program from
Gatekeeper Website.
Enter
Connect Tibbo Ethernet to pc port or switch and connect Tibbo via
12V power (you have option to take 12V power from NetDX or using
12V power adapter).
Mark Tibbo mac address and press Setting tab on right .

A screen will appear and that’s where u configures your unit:
Choose IP and Port for Tibbo unit and use subnet mask (most
common class C)
Use gateway IP-address if not connected directly to pc and using
switch instead.
Then enter same parameters from the picture below (Half Duplax
devices ):
Close the window and save it.
For applying the unit inside Gatekeeper software goes to User Manual

Readers installation
NetDX Controllers fits to most of the readers in the market.
You have the option to work with 12v or 5v readers and many types of
Key Holders, (Easley set up with jumper).
The most important part on reader installation is to define the cables
correctly, see picture below.
(Grey cable is white).
V+ Red cable = Power Supply.
Gnd Black cable = Ground.
Led Blue cable = Led light.
D0 Green cable =Data 0
D1 White cable = Data 1
BUZ Yellow Cable = Its option if the reader have buz option

Power Adopter and Backup Battery
When you unbox the NetDX there is adapter.
First you need to set the adapter, connect it to plug so we can connect it
to the socket.
Then you need to connect the 2 yellow cabels to the controller PWR
connector,( see picture below).
NetDX is connected to Backup battery so if there is power outage the
controller will keep work. There is +- cabels in the 12V BP Battery socket
(see in picture) that connected to the Backup battery.