Gateway 400VTX Guide

www.gateway.com
Replacing the Gateway 400VTX
DVD or DVD/CD-RW drive
This package includes a DVD or DVD/CD-RW drive for your Gateway 400VTX
notebook and these printed instructions.
Installing a replacement drive is a process consisting of three procedures that
must be done in sequence:
1Remove the keyboard.
2Replace the drive.
3Reinstall the keyboard.
Tools you need
You need a small Phillips and small flat blade screwdriver to install the drive.
Preventing static electricity discharge
The components inside your computer are extremely sensitive to static
electricity, also known as electrostatic discharge (ESD).
Before replacing the DVD or DVD/CD-RW drive, follow these guidelines:
■Turn off your notebook.
■Wear a grounding wrist strap (available at most electronics stores) and
attach it to a bare metal part of your workbench or other grounded
connection.
Warning ESD can permanently damage electrostatic
discharge-sensitive components in your notebook. Prevent
ESD damage by following ESD guidelines every time you
replace the DVD or DVD/CD-RW drive.
Warning To avoid exposure to dangerous electrical voltages and
moving parts, turn off your notebook and unplug the power
cord and modem and network cable before opening the
case.

2www.gateway.com
■Touch a bare metal surface on your workbench or other grounded object.
■Unplug the power cord and the modem and network cables.
■Remove the battery. For more information, see “Changing batteries” in
your user guide.
■Disconnect all peripheral devices and remove any PC Cards.
Before working with computer components, follow these guidelines:
■Avoid static-causing surfaces such as carpeted floors, plastic, and packing
foam.
■Remove components from their antistatic bags only when you are ready
to use them. Do not lay components on the outside of antistatic bags
because only the inside of the bags provide electrostatic protection.
■Always hold components by their edges. Avoid touching the edge
connectors. Never slide components over any surface.
Removing the keyboard
To remove the keyboard:
1Follow the instructions under “Preventing static electricity discharge” on
page 1.
2Turn off your notebook, disconnect the AC adapter and modem and
network cables.
3Turn your notebook over so that the bottom is facing up.
4Remove the battery.
5Turn your notebook over so that the top is facing up.
6Open the LCD panel to the normal viewing position.
Warning To prevent risk of electric shock, do not insert any object
into the vent holes of the notebook.

3
Replacing the Gateway 400VTX DVD or DVD/CD-RW drive
www.gateway.com
7Insert the small flat blade screwdriver under the bottom right corner of
the keyboard bezel and gently pry it up.
8Pull the bezel off your notebook. You will hear small snapping sounds as
the bezel comes away from your notebook. Be careful not to break off the
tabs found on the left end of the bezel.
Important Inserting a piece of cloth between the screwdriver and
keyboard and notebook case will help prevent damage to
your notebook.

4www.gateway.com
9With a small Phillips screwdriver, remove the four keyboard screws and
put them in a safe place.
Screws

5
Replacing the Gateway 400VTX DVD or DVD/CD-RW drive
www.gateway.com
10 Raise the back edge of the keyboard, then slowly rotate it toward you so
it lies keys-down on top of your notebook. Be careful not to damage the
LCD panel.

6www.gateway.com
Replacing the DVD or DVD/CD-RW drive
To replace the DVD or DVD/CD-RW drive:
1Remove the screw that secures the drive to the cooling assembly and the
screw that secures the drive to the system board.
Screws

7
Replacing the Gateway 400VTX DVD or DVD/CD-RW drive
www.gateway.com
2Slide the drive out of your notebook.
3Insert the new drive into your notebook, then replace the two screws.

8www.gateway.com
To install the keyboard:
1Rotate the keyboard toward the LCD panel until the keyboard is
almost face-up.
2Insert the front of the keyboard under the palm rest.
3Gently press the keyboard down until it is flat all the way across. The
keyboard should easily fall into place. Be careful not to damage the
LCD panel.
4Replace the four keyboard screws.
Ta b s
Screws

9
Replacing the Gateway 400VTX DVD or DVD/CD-RW drive
www.gateway.com
5Slide the two tabs on the left end of the bezel under your notebook frame.
6Press down on the bezel in several places until it clicks in place.
The bezel is correctly mounted when you can run you finger along the
bezel and find no loose spots. The bezel should be flat all the way across.
7Replace the battery, then turn your notebook over.
8Connect the power adapter and modem and network cables, then turn on
your notebook.
Technical Support
See your user’s guide for Gateway Technical Support information.
Safety, Regulatory, and Legal Information
See your user’s guide for important safety, regulatory, and legal information.
Warning If the bezel is not correctly replaced, your notebook could
be damaged when you try to close the LCD panel.

10 www.gateway.com
© 2003 Gateway, Inc. All rights reserved. Gateway, Gateway Country, the Gateway stylized logo, and the
black-and-white spot design are trademarks or registered trademarks of Gateway, Inc. in the United States and
other countries. All other brands and product names are trademarks or registered trademarks of their respective
companies.
MAN RPL 400 VTX OPTC DRV R0 2/03