Gateway 960 User manual

1
www.gateway.com

i
Contents
Identifying parts in the accessory kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Rackmount handle kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Rackmount rail kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety-related rackmount installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Converting your server to a rackmount server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Removing the front cover, top and side panels, and feet . . . . . . . . . . . . . . . . . 5
Removing and rotating the drives, drive bay adapters, and EMI shield . . . . . . 9
Rotating and installing the front cover drive faceplate . . . . . . . . . . . . . . . . . . . 12
Installing the rackmount handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the front cover and top panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Installing your server into a rackmount cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing the inner rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Attaching the rail assemblies to the rackmount cabinet brackets . . . . . . . . . . 16
Installing the rackmount cabinet brackets and the rail assemblies . . . . . . . . . 18
Mounting the server into the rackmount cabinet . . . . . . . . . . . . . . . . . . . . . . . 21
Securing the server in the cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Getting help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Server Companion CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Gateway Web site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

ii

1
Installing Your Gateway
Server into a
Rackmount Cabinet
This guide provides the information you need to install
your Gateway 960 or Gateway 980 server into a rackmount
cabinet. Read this guide to learn how to:
■Convert a Gateway server into a
rackmount-configured server. See “Converting your
server to a rackmount server” on page 4.
■Install a Gateway rackmount server into a rackmount
server cabinet. See “Installing your server into a
rackmount cabinet” on page 14.

2
Installing Your Gateway Server into a Rackmount Cabinet
www.gateway.com
Identifyingpartsintheaccessorykit
There are two accessory kits for the Gateway 960 or Gateway 980 servers:
■Rackmount handle kit. Install the rackmount handle kit if you are
converting your server to a rackmount server.
■Rackmount rail kit. Install the rackmount rail kit on Gateway 960 or
Gateway 980 servers.
Rackmount handle kit
Rackmount rail kit
8 hex screws
#6-32 × 0.25"
2 rackmount
handles
Inner rail Middle rail Outer rail
2 rackmount cabinet
bracket sets
(4 brackets)
2 rail assemblies
10 screws for
the inner rails
10 screws and hex
head nuts for the rail
assemblies and
rackmount brackets

3
Safety-related rackmount installation instructions
www.gateway.com
Safety-related rackmount
installation instructions
When your Gateway server is installed in a closed or multi-unit rackmount
cabinet, make sure that you consider the following items:
■Ambient temperature
The ambient temperature inside the rackmount cabinet may be greater
than the ambient temperature in the room. Make sure that rackmount
cabinet is ventilated so your Gateway server operates within its specified
maximum operating temperature range. For information about the
maximum operating temperature, see the “Environmental specifications”
section of your user’s guide. The user’s guide is on the Server Companion CD
(SCCD) that shipped with your server.
■Stability
Make sure that your Gateway server is stable in the rackmount cabinet and
mounted according to the rackmount instructions in this installation
guide.
■Input supply
Check the power rating label on the back of your server to make sure that
the power supply circuits are adequate for the server power requirements.
Overloading the power supply circuits may affect the over-current
protection and supply wiring.
■Grounding
Make sure that your rackmount servers are grounded correctly. Pay
particular attention to correctly grounding the power supply connections
on power strips installed inside the rackmount cabinet.
■Disconnect device
The plug on the power cord is the power disconnect device for your
rackmount server. For safety purposes, make sure that the power outlet is
installed near the rackmount cabinet for easy access.

4
Installing Your Gateway Server into a Rackmount Cabinet
www.gateway.com
Converting your server to a
rackmount server
You can convert your Gateway 960 or Gateway 980 server to a rackmount
server. Before converting your server, make sure that the server is on a stable
work surface, such as a strong table or counter.
Although your server configuration may vary from the server configuration
shown in the following instructions, the general installation process will be
similar. To convert your server to a rackmount server, you need to complete
the following tasks in sequence:
1Remove the front cover, side and top panels, and feet.
2Remove and rotate the drives, drive bay adapters, and EMI shield 90
degrees.
3Rotate and install the front cover drive faceplates.
4Install the rackmount handles.
5Install the front cover and top panel.
If your server came from Gateway pre-configured for rack installation, go to
“Installing your server into a rackmount cabinet” on page 14.
Warning To avoid injury or damage to the server, we recommend
that two people lift the server.

5
Converting your server to a rackmount server
www.gateway.com
Removing the front cover, top and side panels,
and feet
Tools you need to complete this task:
To remove the front cover:
1Turn off your server, then disconnect the power cord and all other cables
connected to the server.
2Unlock the hot-swappable RAID bay cover door, press the cover release latch
on each side of the front cover, then pull the cover away from the case.
Phillips screwdriver
Needle-nose pliers
Cover
release
latch
Lock
Cover
release
latch

6
Installing Your Gateway Server into a Rackmount Cabinet
www.gateway.com
To remove the top panel:
1Remove the two top panel screws on the back of the case.
2Slide the top panel toward the back of the case, then lift the panel up and
away from the case.
Top
panel
screw
Top
panel
screw