GATEXPERT CN Series User manual

MEN-003-N
GARAGE DOOR OPENER
INSTALLATION MANUAL
CN SERIES
Website: www.gatexpertstore.com
E-mail: [e-mail]

1
Attention to security
To ensure your safety, reduce accidents happens, before installation
please must read the installation manual carefully, and operation is strictly
complying with the installation manual. If you have some questions, please
ask the specialists and the dealers.
1) The installation worker must inspect the door before installation, only
allows installation the opener at balance state, Otherwise it could have
serious consequences.
2) When the door is running, no people and object can across, or stay
below the door.
3) It is forbidden to use the remote control when you can not see the door
running, avoid accidents and misuse of the garage door opening.
4) The mechanical limiters should add the doors two side to prevent the
body slid off the door.
Note :If you do not have the side door ,please must installation
blackouts unlocking device so as to open the door by hand when
blackout.
Tools needed
During assembly, installation and adjustment of the opener, instructions
will call for hand tools as illustrated below.

3
2
Technical parameter
Rated voltage:
AC230V±10% 50Hz
Open and close force
600N /800N/ 1000N /1200N
Motor:
24VDC
Transmission frequency:
433.92MHz
Decoding:
Rolling Code
Transmitter:
27A 12V /CR2032 3VBattery
Standby power:
＜6W
Work temperature:
-20℃~+50℃
Courtesy Light:
3 minutes
Rated Operation Time:
4 minutes

4
3
Install the Header Bracket and the door bracket
G3
H8
Attach the Rail to the Header Bracket
H7
H5
G4
H1

5
4
Door arm connection
1. Close the door. Disconnect the trolley
by pulling the emergency release handle.
2. Attach the straight door arm to the outer
trolley using the Shouldered shaft, short (H6).
Attach with the Cotter Pin (H5).
H5
H6

6
5
3. Attach the curved door arm to the door
bracket using the Shouldered shaft, short
(H6). Attach with the Cotter Pin (H5).
4. Bring arm sections together. Find two pairs
of holes that line up and join sections. Select
holes as far apart as possible to increase door
arm rigidity and attach using the bolts (H4) and
nuts (H3).
H5
H6
H3
H4

7
6
5. Pull the emergency release handle toward the garage door
opener until the trolley release arm is horizontal. The trolley will
re-engage automatically when the garage door opener is
activated.

7
Control Box---Overview
OP
ST
CL
PR
ST
Enter Function Setup Menu
Confirm chosen function or value
PR
In Standby :Enter Transmitter Setup Menu
OP
In Setup Menus: Scroll Function
CL
In Setup Menus: Scroll Function
Basic function settings
1 Adjusting the Open and Close Limits
OP
ST
CL
PR
Press ‘ST ’ button and hold on until the LED
displays ‘1’.
OP
ST
CL
PR
Press and hold the ‘OP ’ button, until the door
reaches the desired open position.
NOTE: Fine adjustments can be made by toggling
OP &CL buttons.
OP
ST
CL
Press the ‘ST’ button The LED displays ‘2’.
OP
ST
CL
PR
PR

8
Press and hold the ‘CL‘ button until the door
reaches the desired close position. For fine
adjustments toggle OP &CL buttons.
OP
ST
CL
PR
Press the ‘ST’ button to confirm the close position.
The door is now set for normal operation.
2 Programming Hand Transmitters
OP
ST
CL
PR
NOTE: Hand transmitters that are supplied with
the door opener is pre-programmed.
Press and hold the PR button until the LED
displays ‘ ●’.
Now press the button on the hand transmitter
you want to use, pause for 1 second, then press
the same button on the hand transmitter again
for 1 second. The LED will flash to confirm the
code, then turn off.
3 Deleting Stored Hand Transmitters
OP
ST
CL
PR
Press PR button until the LED displays ‘ ●’,
Keep pressing the button, the LED is off, All
stored remotes will be deleted.

9
Advanced function settings
1 Time to close
PR
OP
ST
CL
Press ‘OP ’ button and hold on until the LED
displays ‘ ’. Press the OP &CL buttons to select
closing time.
Level
0
1
2
3
4
5
Value
0
1minute
2
3
4
5
Level
6
7
8
9
-
-
Value
6
7
8
9
-
-
OP
ST
CL
PR
Press the ‘ST ’ button to confirm it.
2 Safety Photo Beam
PR
OP
ST
CL
Press ‘CL’ button and hold on until the LED
displays ‘ ’. Press the’ OP orCL ‘buttons to open
or close the function.
open the function
close the function
OP
ST
CL
Press the ‘ST ’ button to confirm it.
GND
+__
+__
NC
PR
+24V
PB
GND
+24V

10
3 Close force adjustment
DIP1
2
1
The jumper connects ‘ DIP1’ and ‘2’ meant MAX close force.
DIP1 2
1
DIP1
21
The jumper connects ‘2’ and ‘ 1’ meant 50% close force.
External Interface
+24
PBSW
GND
PB
ALM+
ALM-
SD+
SD-
NO
Backup battery
-
BLK
Battery
+24V
+
NC
RED
BAT