GCX AG-0019-07 User manual

DU-AG-0019-07 Rev A 10/26/05 GCX Corp Page 1 of 5
GCX Mounting Assembly Installation Guide
Philips MP90 (M8010A) Mounting Kit for Drager Zeus
The purpose of this guide is to:
1. Describe attachment of Down Post to Arm.
2. Describe attachment of Arm to 38mm Post.
3. Describe mounting of FMS.
4. Describe attachment of Zeus Channel Kit.
5. Describe attachment of CPU Flush Mount.
6. Describe operation/adjustment of M-Series Arm.
Parts Reference
The parts list below includes parts and hardware that will be used in this installation procedure.
Tools Required: Phillips screwdriver, 5/32'' and 1/8'' hex keys (provided).
Attaching Down Post to Arm
Fasten 3.5'' Down Post to bottom of M-Series Arm in accordance with separate GCX Mounting Assembly Installation
Guide titled: M and VHM Series Down Post Kit (DU-WMM-0006-01).
Mounting M-Series Arm on 38mm Post
1. Using the 5/32'' hex wrench provided, mount Arm on post by fastening Clamping Block to Arm with two (2) #10-32 x
7/8'' SHCS as shown below.
Item # Description Qty
1 M-Series Articulating Arm Assembly with 38mm Clamps 1
2 #10-32 x 7/8” SHCS 2
3 3.5'' Down Post 1
4 #10-32 x 3/8'' Socket Head Cap Screw 3
5 Zeus Vertical Channel Kit 3
6 M6 x 16mm SHCS 4
7 CPU Flush Mount Pan 1
8 M3 x 8mm PHMS 4
9 M3 Flat washers 4
10 CPU Spill Shield 1
11 #8-32 x 5/16” PHMS 2
12 Molded Slide 2
13 #8-32 x 5/8” PHMS 8
14 5/32'' Hex Key 1
15 1/8'' Hex Key 1

DU-AG-0019-07 Rev A 10/26/05 GCX Corp Page 2 of 5
Mounting Display, Remote Speedpoint, External Alert Device, and Power Supply
Please refer to separate installation guide: Philips MP90 Remote Speedpoint Mounting Bracket and Adapter, and External
Alert Device Mounting Bracket (DU-AG-0019-80). Installation Note: Flat Panel Display mounting is also covered in
referenced installation guide. Mount Display according to Section 2.0 for a 15'' Display, or Section 3.0 for a 17'' Display.
Mounting FMS on Down Post
1. Mount Rack on Down Post by placing the Clamp around the Down Post and tightening the Knob.
#10-32 x 7/8'' SHCS (2)
Clamping Block
38mm Pos
t
M-Series Arm
Clamp
Down Post

DU-AG-0019-07 Rev A 10/26/05 GCX Corp Page 3 of 5
Mounting Zeus Channel Kit
1. Position the Zeus Channel Kit over the (2) vertical Drager tracks.
2. Mount the Zeus Channel Kit by running M6 x 16mm SHCS (2 on each end)
through the slots and into the brass fittings in the Drager tracks.
Attachment of CPU Flush Mount Pan
1. Remove the four (4) black plastic feet and the black lock lever from the bottom of the CPU. The threaded holes (left
empty by removal of the feet) will become mounting holes for the Mounting Pan.
2. Orient Pan as shown below, and fasten Pan to the bottom of CPU with four (4) M3 x 8mm PHMS and Flat Washers.
M6 x 16mm SHCS (4)
Remove Lever
Remove Feet (4)
Bottom of CPU
M3 x 8mm PHMS (4)
Flat Washer (4)
Front of CPU
Mounting Pan

DU-AG-0019-02 Rev A 12/30/04 GCX Corp Page 4 of 5
Attaching Spill Shield and Channel Slides
1. Fasten Spill Shield to Mounting Pan with two (2) #8-32 x 5/16” PHMS and Flat Washers as shown below left. Position
Spill Shield so the CPU will be centered below the Shield when mounted.
2. Fasten each Slide to Mounting Pan with four (4) #8-32 x 5/8” PHMS, as shown below right.
Assembling CPU to Zeus Channel Kit
1. Align Slides with Vertical Channel, and insert CPU.
8-32 x 5/16” PHMS (2)
Flat Washer (2)
Spill Shield
Attach Slides in these
Positions (2)
8-32 x 5/8” PHMS (4)

DU-AG-0019-02 Rev A 12/30/04 GCX Corp Page 5 of 5
Pivot Tension Bolt
Flexible Cable Covers
Pass-through Slide
Tilt Tension Adjustment Screws (2)
M-Series Arm Operation and Adjustment
Swiveling the Mounted Instrument
1. To swivel the mounted instrument simply push or pull the corners of the
instrument.
2. To adjust swivel tension, remove bolt cap or existing Down Post from Swivel
Cup (bottom of front end of Arm). Tighten or loosen the Swivel Tension Bolt
using a 1/2'' [13 mm] socket driver.
Tilting the Mounted Instrument
1. To tilt the instrument, grasp the top and bottom of the instrument and tilt it to the
desired angle.
2. To adjust tilt tension, equally tighten or loosen the two (2) Tilt Tension
Adjustment screws using the supplied 5/32'' hex key.
Pivoting the Arm
1. To pivot the Arm at the Slide, simply push on the side of the Arm or
mounted instrument.
2. To adjust pivot tension, loosen or tighten the Pivot Tension Bolt using a
1/2" [13 mm] socket driver.
Cable Management
Two cable management features allow convenient placement and flow of
cables:
1. An open cavity beneath the arm (with flexible cable covers) allows
management of cables between the front and rear of the arm.
2. A “pass-through” channel at the rear of the slide allows cables to pass
behind the arm within the Channel.
Note: If cable connectors are too large to fit through the pass-through,
try placing the cables in the "pass-through" before installing the arm in
the Channel. Contact GCX for optional Channel Covers available to
further manage the flow of cables in the Channel.
Cleaning
CAUTION: GCX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling
infection. Consult your hospital’s infection control officer or epidemiologist. To clean or sterilize mounted instruments or
accessory equipment, refer to the specific instructions delivered with those products.
1. The mounting assembly may be cleaned with most mild, non-abrasive solutions commonly used in the hospital
environment (e.g. diluted bleach, ammonia, or alcohol solutions).
2. The surface finish will be permanently damaged by strong chemicals and solvents such as acetone and
trichloroethylene.
3. Do not use steel wool or other abrasive material to clean the mounting assembly.
4. Damage caused by the use of unapproved substances or processes will not be covered by warranty. We
recommended that you test any cleaning solution on a small area of the arm that is not visible to verify compatibility.
5. Never submerge the arm, and do not allow liquids to enter the arm. Wipe any cleaning agents off of the arm
immediately, using a water-dampened cloth. Dry the arm thoroughly after cleaning.
Swivel Tension Bolt