GE Security SP-PoE User manual

GE
Security
P/N 1069176-EN • REV 1.01 • ISS 21MAR10
SP-PoE Splitter User
Manual

SP-PoE Splitter User Manual i
Copyright © 2010 GE Security, Inc.
This document may not be copied in whole or in part or otherwise
reproduced without prior written consent from GE Security, Inc.,
except where specifically permitted under US and international
copyright law.
Disclaimer The information in this document is subject to change without notice.
GE Security, Inc. (“GE Security”) assumes no responsibility for
inaccuracies or omissions and specifically disclaims any liabilities,
losses, or risks, personal or otherwise, incurred as a consequence,
directly or indirectly, of the use or application of any of the contents
of this document. For the latest documentation, contact your local
supplier or visit us online at www.gesecurity.com.
This publication may contain examples of screen captures and
reports used in daily operations. Examples may include fictitious
names of individuals and companies. Any similarity to names and
addresses of actual businesses or persons is entirely coincidental.
Trademarks and
patents
GE and the GE monogram are trademarks of General Electric
Company.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Intended use Use this product only for the purpose it was designed for; refer to the
data sheet and user documentation for details. For the latest product
information, contact your local supplier or visit us online at
www.gesecurity.com.
FCC compliance This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.

Regulatory
information
N4131
Manufacturer GE Security, Inc.
HQ and regulatory responsibility:
GE Security, Inc., 8985 Town Center Parkway,
Bradenton, FL 34202, USA
EU authorized manufacturing representative:
GE Security B.V., Kelvinstraat 7,
6003 DH Weert, The Netherlands
European Union
directives
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information For contact information see our Web site: www.gesecurity.com.
For contact information see our Web site: www.gesecurity.eu.
ii SP-PoE Splitter User Manual

Content
Chapter 1 Overview 1
Package Contents 2
Introduction 2
Product Overview 3
Chapter 2 Hardware Installation 7
Before Installation 7
Installation 9
SP-PoE Splitter User Manual i

Chapter 1
Overview
The GE Security SP-PoE is an IEEE 802.3af Power over Ethernet device that
splits the 48VDC power input over an Ethernet cable into separate 5V and
12V DC power outputs.
SP-PoE Splitter User Manual 1

Chapter 1: Overview
Package Contents
Your SP-PoE Splitter carton should contain the following items:
•The Power over Ethernet Splitter x 1
•User's Manual x 1
•15cm UTP straight network cable x1
•DC Plug cable x 2
If any item is missing or damaged, please consult the dealer from whom you
purchased you SP-PoE Splitter module.
Introduction
The GE Security SP-PoE is an IEEE 802.3af Power over Ethernet device that
splits the 48VDC power input over an Ethernet cable into separate 5V and
12V DC power outputs. The SP-PoE works with IEEE 802.3af power source
equipment (PSE). This frees device deployment from restrictions due to power
outlet locations and eliminate the costs for additional AC wiring and reduces
the installation time.
When the PSE inserts DC Voltage into the CAT 5 cable, it allows the cable
between the PSE and SP-PoE to transfer data and power simultaneously. The
maximum distance between the PSE and SP-PoE is 100M.
Product Features
•Complies with the IEEE 802.3z Gigabit Ethernet standard
•1 X 1000Mbps fiber port
•Plug and Play Installation
•SFP1000SX-220 provides distance up to 220m over 62.5/125µm
fiber cable and 550m over 50/125µm fiber cable
2 SP-PoE Splitter User Manual

Chapter 1: Overview
•SFP1000LX-10Km provides distance up to 10km over 9/125µm
single mode fiber cable
Product Overview
Figure 1 shows the left and right side panels of the SP-PoE Splitter
Figure 1: Left and right side panels of the SP-PoE
LED Indicators
LED Color Function
PoE ready /
in-use Green Lights to indicate the port is providing 48VDC in-line power.
SP-PoE Splitter User Manual 3

Chapter 1: Overview
Product Specifications
Model SP-PoE
Interface
Ethernet + DC Copper Port 1 x 10/100Base-TX with IEEE 802.3af PoE
PD for data + DC in
RJ-45 connector
Ethernet Copper Port 1 x 10/100Base-TX for data out
RJ-45 connector
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PD
PoE Input Pin Assignment 1/2(+), 3/6(-) End-Span or 4/5(+), 7/8(-)
Mid-Span
PoE Input Voltage 48V DC ( Range 44 to 56VDV)
Hardware Specification
Data Rate 10/100Mbps (vary on Ethernet device
attached)
Throughput (Packet per second) 148810pps@64Bytes
DIP Switch 5VDC / 12VDC output voltage
Output DC Connector DC Jack 5.5 x 2.5 mm receptacle in the
central post
Output Power 12W max
Number of Device can be powered 1
Ethernet Cable TIA/EIA-568, Category 5/5e cable
Installation Standalone or Wall mountable
Material Plastic
Standards Conformance
Standard Compliance IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 10/100Base-TX Fast Ethernet
IEEE 802.3af Power over Ethernet PD
4 SP-PoE Splitter User Manual

Chapter 1: Overview
Physical Specifications
Dimensions (W × D × H):
2.87” x 2.17” x 0.94” / 73 x 55 x 24mm
Weight:
0.22 lbs / 50g
Environmental Specifications
Operating:
Temperature: 0°C ~ 50°C
Relative Humidity: 5% ~ 90% (non-condensing)
Storage:
Temperature: -20°C ~ 70°C
Relative Humidity: 5% ~ 90% (non-condensing)
Electrical Specification
Output Voltage:
DIP switch 5V: 5VDC, 2.0A max
DIP switch 12V: 12VDC, 1.0A max
NOTE: This product is intended to be supplied by a UL Listed Direct Plug-In
Power Unit marked "Class 2" or "LPS" and output rated 48 VDC, 3 Amp
minimum.
SP-PoE Splitter User Manual 5

Chapter 1: Overview
6 SP-PoE Splitter User Manual

Chapter 2
Hardware
Installation
Before Installation
If your network environment is very difficult to find a power socket for your
AC-DC Adapter of networked device, the SP-PoE provides DC power for this
Ethernet Device conveniently and easily.
The SP-PoE separates the power out and provides two kind of DC power
output through its DIP switch and its voltage and current shown as below:
•5V DC/2A
•12V DC/1A
SP-PoE Splitter User Manual 7

Chapter 2: Hardware Installation
Figure 2: 5V/12V DC out DIP switch
The default value is set on 5V. MS-POE and SP-PoE units can be installed in
pairs. However, use of third-party device is allowed if the device complied
with IEEE 802.3af standard.
8 SP-PoE Splitter User Manual

Chapter 2: Hardware Installation
Installation
To connect the hardware, do the following:
1. Connect a standard network cable from "Ethernet+DC" of MS-POE to
"Ethernet+DC" of SP-PoE. The POE LED of SP-PoE/MS-POE will start to
flash continuously.
Figure 3 MS-PoE/SP-PoE application
Note: The SP-PoE only accepts IEEE 802.3af equipment. Other in-line power
devices may cause the SP-PoE to malfunction.
2. Connect the UTP cable in the package from "Ethernet" of SP-PoE to
the RJ-45 port of remote device.
3. Connect proper DC plug from "DC OUT" of SP-PoE to remote device.
Caution: Please ensure the output voltage is correct for remote device.
Otherwise, it will damage your remote device.
4. Power on the remote device and the LED indicator on SP-PoE will
remains on.
SP-PoE Splitter User Manual 9

Chapter 2: Hardware Installation
Connect with other802.3af devices
The SP-PoE also provides an alternative way to connect to non IEEE 802.3af
devices and to connect with an IEEE 802.3af in-line power device like a
Power over Ethernet Switch. See the figure below.
Figure 4: PSE/SP-PoE application
10 SP-PoE Splitter User Manual