GE AHH08 Operating instructions

GEAppliances.com
0
0_
0_
Safety Instructions ............. 2,3
Operating Instructions
Controls ........................... 4-6
Care and Cleaning
Air Filter .............................. 6
Outdoor Coils ......................... 6
Installation Instructions ...... 7-1o
Troubleshooting Tips ............ 11
Normal Operating Sounds ............ 11
Consumer Support
Consumer Support .......... Back Cover
Ownership Registration for
Customers in Canada only ........ 13, 14
Warranty for Customers
in Canada ........................... 16
Warranty for Customers
in the U.S.A........................... 15
*ENERGY STAR ® labeled product
I
ENERGYSTAR
As an ENERGYSTAR®partner, GE has
determined that this product meets
the ENERGYSTAR®guidelines for
energy efficiency.
AHH08*
AHHI0*
AHH12*
O_ Write themodelandserial numbershere:
Model #
Serial#
Find these numbers on a label on the
sideof the air conditioner.
In Canada, contact us at:
www.GEAppliances.ca 4.9-7676 12-10 GE

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
AWARNING!
Foryour safety, the information in this manual must be followed to minimize the risk of fire, electric
shock or personal injury.
SAFETYPRECAUTIONS
Use this appliance only for its intended
purpose as described in this Owner's
IVlonual.
This air conditioner must be properly
installed in accordance with the Installation
Instructions before it is used.
Never unplug your air conditioner by pulling
on the power cord. Always grip plug firmly
and pull straight out from the receptacle.
Replace immediately all electric service
cords that have become frayed or otherwise
damaged. A damaged power supply cord
must be replaced with a new power supply
cord obtained from the manufacturer and
not repaired. Do not use a cord that shows
cracks or abrasion damage along its length
or at either the plug or connector end.
Turn the unit OFFand unplug your air
conditioner before cleaning.
GEdoes not support any servicing of the
air conditioner. We strongly recommend
that you do not attempt to service the air
conditioner yourself.
For your sufety...do not store or use
combustible materials, gasoline or other
flammable vapors or liquids in the vicinity
of this or any other appliance.
All air conditioners contain refrigerants,
which under federal law must be removed
prior to product disposal. If you are getting
rid of an old product with refrigerants, check
with the company handling disposal about
what to do.
If the receptacle does not match the plug,
the receptacle must be changed out by a
qualified electrician.
These R/410Aair conditioning systems
require contractors and technicians to
use tools, equipment and safety standards
approved for use with this refrigerant.
DO NOT use equipment certified for
R22 refrigerant only.
2
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
For personal safety, this appliance must be
properly grounded.
DO NOT use an adapter plug with this appliance.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric
shock hazard from this appliance.
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
Where a 2-prong wall outlet is encountered,
it isyour personal responsibility and obligation to
have it replaced with a properly grounded
3-prong wall outlet.
The air conditioner should always be plugged
into its own individual electrical outlet which has
a voltage rating that matches the rating plate.
Power cord includes a current interrupter device.
A test and reset button is provided on the plug
case. The device should be tested on a periodic
basis by first pressing the TESTbutton and
then the RESETbutton while plugged into the
outlet. If the TESTbutton does not trip or if the
RESETbutton will not stay engaged, discontinue
use of the air conditioner and contact a qualified
service technician.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
See the Installation Instructions, Electrical
Requirements section for specific electrical
connection requirements.

GEAppliances.com
AWARNING!
USEOFEXTENSIONCORDS
RISK OF FIRE. Could cause serious injury or
death.
•DO NOT use an extension cord with this
Window Air Conditioner.
•DO NOT use surge protectors or multi-outlet
adaptors with this Window Air Conditioner.
READAND FOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCTIONS

About the controlson the air conditioner
Features and appearance will vary.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.
NOTE:Thedisplay always
showsthe roomtemperature
exceptwhen setting the Set _!
temperatureorthe Delay
timer. e--...,m
Fan Delay
ImFan
Only mHigh Im On
Cool _Hed _Off
Energyll Low
Saver
!Auto
Temp/ Delay
Unit power_
on/off
Modeselect '_
Fanspeed_
Delay1-24hr--_-
Temperature,_lP _
set/DelayTimer
Increaseand
Decrease
@od_
e_
@el_
z4_Z)
Temp /Delay
['w'D
Air Conditioner Controls Remote Control
Controls
Power Pad
Turns air conditioner on and off.When turned
on,the display will show the room temperature.
Display
Shows the room temperature or time remaining
on the Delaytimer. Showsthe Settemperature
while setting the temperature in Cool or Energy
Saver modes.TheSet light willturn on while
setting.
Tamp and Delay Increase •/Decrease •
Pads
Useto set temperature or delaytime.
Temperature can be set in Cool, Energy Saving
and Auto mode.
Mode Pad
Useto set the air conditioner to FanOnly, Cool,
Energy Saver orAuto mode.
Fan Speed Pads
Useto set the fan speedto Low, Med, or High
on the unit.
Delay Pad
Delay ON--When the air conditioner is off,it con
be set to automatically come on in 1 to 24 hours
at its previous mode and fan settings.
Delay OFF--Whenthe air conditioner ison,
itcan be setto automatically turn offin 1 to
24 hours.
How to set:
Pressthe Delay 1-24hr pad on the unit or the
remote control. Eachtouch of the Increase • /
Decrease• padson the unit or the Increase +/
Decrease - pads on the remote control will set
the timer in 1-hour intervals.
To review the remaining time onthe Delay
1-24hr timer, press the Delay 1-24hr pad on the
unit or the remote control. Usethe Increase • /
Decrease • pads on the unit or the Increase+
/ Decrease - padson the remote control to set
a new time ifdesired.
To cancel the timer, press the Delay 1-24hr pad
until the light on the Delay 1-24hr pad goes off.
4

GEAppliances.com
Do Not Operate in Freezing Outdoor Conditions
Thiscool-only air conditioner was not designed for
freezing outdoor conditions. It must not be usedin
freezing outdoor conditions.
Remote Control
To ensure proper operation, aim the remote
control at the signal receiver on the air
conditioner.
Theremote control signal has a range of
up to 20 feet.
Make sure nothing isbetween the air conditioner
and the remote control that could block the
signal.
Make sure batteries are fresh and installed
correctly as indicated on the remote control.
Cool Mode
Usethe Cool mode at Low, Med, High or Speedfor
cooling. Usethe Temperature Increase •/ Decrease
• pads to set the desiredtemperature between 61°F
and 86°Fin 1% increments.
An electronicthermostat isusedto maintain the room
temperature. Thecompressorwill cycleon
and off to keepthe room at the set levelof comfort.
Setthe thermostat at a lower number and the indoor
air will become cooler.Setthe thermostat at a higher
number and the indoor air will become warmer.
NOTE:If theair conditioner isoff and isthen turned on
while set to a Cool setting or if turned from a fan
setting to a Cool setting,it may take approximately
3minutes for the compressor to start and coolingto
begin.
Cooling Descriptions
For Normal Cooling-Select the Cool mode and
High orMad fan with a middle set temperature.
For Maximum Cooling--Select the Cool mode
and High fan with a lower set temperature.
For Quieter end Nighttime Cooling-Select the
Cool mode and Low fan with a middle set
temperature.
Energy Saver Mode
Controls the fan.
ON--The fan will cycleon and off with the
compressor.This resultsin wider variations of room
temperature and humidity. Normally usedwhen the
room isunoccupied. NOTE:Thefan may continue to
run for a short time after the compressorcyclesoff.
OFF--Thefan runsall the time, while the compressor
cycles on and off.
Fan Only Mode
Usethe FanOnly Modeat Low, IViedor Highfan
speedto provide air circulation and filtering without
cooling. Sincefan-only settings do not provide
cooling, a Settemperature cannot be entered. The
room temperature will appear
in the display.
Auto Fun Speed
Setto Auto for the fan speedto automatically set
to the speedneeded to provide optimum comfort
settings with the set temperature.
If the room needsmore cooling, the fan speed
will automatically increase.Ifthe room needs less
cooling, the fan speedwill automatically decrease.

About the controlsonthe air conditioner
Additional important information.
Air Direction
Usethe leverto adjust the air direction left,right, up
and down.
Careand cleaningof the air conditioner.
Grille and Case
Turn the air conditioner off and remove the plug from
the wall outlet before cleaning.
Air Filter
Theair filter behind the front grille should be checked
and cleaned at least every 30 days or
more often if necessary.
Toremove:
Open the inlet grille by pulling downward on the tabs
at the top upper corners ofthe inlet grille until the
grille is in a 450position. Removethe filter.
Cleanthe filter with warm, soapy water. Rinseand let
the filter dry before replacing it. Donot cleanthe filter
in a dishwasher.
ik CAUTION:_oNOro_erotetheair
conditioner without o filter becausedirt and lint will
clog it and reduceperformance.
Toclean, usewater and a mild detergent. Do not use
bleachor abrasives.
Outdoor Coils
Thecoils on the outdoor sideof the air conditioner
should be checked regularly. Ifthey are clogged with
dirt or soot,they may be professionallycleaned.
6
How to Insert the Batteries in the Remote Control
-_---1 emove the buttery cover by twisting it
according to the arrow direction. A coin can be
usedto twist the cover.
12] Insertnew battery, making surethat the (+)and
(-) of battery are installed correctly.
I-_ Reattachthe cover bytwisting it back
into position.
NOTES:
Useone CR2025 (3V)Lithium battery.
Removethe batteriesfrom the remote control if
the system isnot going to be usedfor a long time.

]l.s,a,,a:io".s,ruc,,o.s] ,irCo.di,io.er]
J I"_"I Questions? Call 800.GE.CARES(800.432.2737)or Visit our Website at: GEAppliances.com
|
In Canada, call 1.800.561.3344or visit www.GEAppliances.ca I
BEFOREYOU BEGIN
Read these instructions completely
and carefully.
• IMPORTANT- Sovetheseinstructions
for Iocol inspector's use.
•IMPORTANT--Observe oil governing
codes ond ordinonces.
•Note to Installer- Be sure to leove these
instructions with the Consumer.
•Note to Consumer - Keep these instructions for
future reference.
•Skill level- Instollotion of this opplionce
requires bosic mechonicol skills.
•Completion time - Approximotely 1 hour
• We recommend thor two people instoll
this product.
• Proper instollotion is the responsibility
of the instoller.
• Product foilure due to improper instollotion is not
covered under the Worronty.
• You MUST use oil supplied ports ond use proper
instollotion procedures os described in these
instructions when instolling this oir conditioner.
ELECTRICALREQUIREMENTS
(_ ome models require o llS/120-voltAC,
60-Hz grounded outlet protected with o
15-omp time-deloy fuse or circuit breoker.
The 3-prong grounding plug minimizes the
possibility of electric shock hozord. If the woll outlet you
plon to use is only o 2-prong outlet,
it isyour responsibility to hove it reploced with
o properly grounded 3-prong woll outlet.
©Some models require 230/208-volt AC,
protected with o time-deloy fuse or circuit
breoker. These models should be instolled on
their own single bronch circuit for best
performonce ond to prevent overlooding
house or oportment wiring circuits, which
could cuuse o possible fire hozord from
overheoting wires.
ACAUTION:
Do not, under any circumstances, cut or remove the
third (ground) prongfrom the power cord.
Do not change the plug on the power cord of this air
conditioner.
Aluminum house wiring may present special
problems--consult a qualified electrician.
TOOLSYOUWILL NEED
Phillips head screwdriver
Drill and 1/8" drill bit
Pencil Ruler or tape measure
Level Scissors or knife
Power cord includes o current interrupter
device. A test ond reset button is provided on the
plug cuse. The device should be tested on u periodic
bosis by first pressing the TESTbutton ond then the
RESETbutton while plugged into the outlet. If the
TESTbutton does not trip or if the RESETbutton will not
stoy enguged, discontinue use of the oir conditioner
ond contoct o quolified service technicion.

Installation Instructions
PARTS INCLUDED
(Appearancemayvary) Foam top window
gasket
\
SideCurtain
(2)
Side Curtain
Frame (2)
Air
conditioner
\Remote
Control --
Side Brackets (2)
f ..............................................
@@
@_
0
Window locking
bracket (1)
Type A (4) Type B (9)
8

Installation Instructions
D WINDOW REQUIREMENTS
•Theseinstructions are for astandard double-hung
window. You will need to modify them for other types
of windows.
• The air conditioner can be installed without the
side curtain panels if needed to fit in a narrow
window. See the window opening dimensions.
• All supporting parts must be secured
to firm wood, masonry or metal.
• The electrical outlet must be within reach of the
power cord.
• Follow the dimensions in the table and illustration
for your model.
Models A B
AHH08LP 13 3/8" min. 25"- 36"
AHH10AP, 14 9/16" min. 24 1/2"- 38"
AHH12AP
I !
B==4]
A
B
(Withside curtain panels)
Y
r_l STORM WINDOW REQUIREMENTS
A storm window frame will not allow the air
conditioner to tilt toward the outside, and will keep it
from draining properly.
To adjust for this, attach a piece of wood to the sill.
WOOD PIECES
WIDTH: 2"
LENGTH:Long enough to fit inside the window
frame.
THICKNESS: To determine the thickness, place a
piece of wood on the sill to make it 1/2" higher
than the top of the storm window frame or the vinyl
frame.
Attach securely with nails or screws provided by the
installer.
1/2" higher
than storm
window
frame
Storm window
frame
1/2"higher
than vinyl frame
_ _(°ns°mewind°ws /Woo d
__ Sill n_
I Vinylframe , i
DPREPARETHEAIR CONDITIONER
[] Install the top moutning rail with Type A screws,
4 for AHH12 and AHH10 and 3 for AHH08 from
the outside of the case.
Top Mounting rail
!
Bottom mounting rail
r_ Slide the side curtain panels into the side
panel rails.
Slide left and right side curtain frames
into top and bottom rails. Make sure that
side curtains snap into side of the frames.
Top mounting rail Top ight
Top left i_
Bottom mounting rail
9

Installation Instructions
DINSTALL THEAIR CONDITIONER
IN THEWINDOW
[] Mark the center of the window. Set the
air conditioner in the window so that is it
centered. Place the air conditioner so that
front edge of the bottom mounting rail is
against the back edge of the sill.
DBring the window down so that the front
edge of the top mounting is in front of the
window. Make sure that the air conditioner
is level or tilting slightly to the outside.
Top rail
_o- Window sash
About
5o
BI Extend the curtain panels until they fill the
window. Mark the location of the holes in
each corner. Use the drill and 1/8" drill bit
to drill pilot holes. Use 4 type B screws to
secure the side panels in place.
I
Type B screws
DSECUREAIR CONDITIONER
r_ Loosen the screw on the right hand side of the
air conditioner near the bottom.
\
FB1 Slide a side bracket over the screw so that the
bracket is resting on the window sill. Tighten
the screw.
\
rc1 Use a 1/8" drill bit to drill a starter hole into
the window sill through the holes in the side
bracket. Use two type B screws to attach the
side bracket to the window sill.
Repeat the side bracket installation on the left
side.
10

Installation Instructions
[] INSTALLSUPPORTBRACKETAND
FOAMTOPWINDOW GASKET
Use type B screw to instoll the window lock
bracket on top of bottom window.
DACAUTION:
To prevent broken glass or
damage to windows, on
vinyl or other similarly
constructed windows,
attach the window locking
bracket to the window side
jamb with one Type B
screw.
Vinyl
Wood
rB-]
rcq
Cut the foam top window gasket to the window
width.
Stuff the foam between
the glass and the
window to prevent
air and insects from
getting into the room.
NOTE: If the gasket supplied does not fit your
window, obtain appropriate material locally to
provide a proper installation seal.
11

TroubleshootingTips.
Possible Causes
Air conditioner
does not start
What To Do
The air conditioner
is unplugged.
The fuse is blown/circuit
breaker istripped.
Power failure.
• Make surethe air conditioner plug is pushed
completely into the outlet.
• Checkthe housefuse/circuit breaker boxand replace
the fuse or reset the breaker.
•The unit will automatically restart inthe settings last
usedafter the power isrestored.
•There is a protective time delay (approximately
3 minutes) to prevent tripping of the compressor
overload. Forthis reason, the unit may not start
normal cooling for 3 minutes after it isturned
back on.
The current interrupter • Pressthe RESETbutton located on the power cord plug.
device is tripped. • If the RESETbutton will not stay engaged, discontinue
use of the air conditioner and contact a qualified
service technician.
Air conditioner does Airflow is restricted. • Hake surethere are no curtains, blinds or furniture
not cool as it should blocking the front of the air conditioner.
The tamp control may ,Turn the temperature knob to u higher number.
not be set correctly.
The air filter isdirty. ,Clean the filter at least every 30 days.
Seethe Cureand Cleaningsection.
The room may have been hot. ,When the air conditioner isfirst turned on,you need
to allow time for the room to cool down.
Cold air is escaping. ,Check for open furnace registersand cold air returns.
Cooling coils have iced up. ,See "Air conditioner freezing up" below.
Air conditioner Ice blocks the air flow *On models with control knobs,set the mode control at
freezing up and stops the air conditioner High Fanor HighCoolwith the Temp at i or 2.
from cooling the room.
Water drips outside Hot, humid weather. ,This isnormal.
The air conditioner is not • Forproper water disposal,make surethe air conditioner
tilted to the outside, slantsslightly from the case front to the rear.
basepan
il :C ! iL !! ! !i7_¸i( (i
iS!il ¸¸¸(( :ICICJICJICI ¸
Moisture removed from air
and drains into base pan. • This isnormal for a short period in areas with little humidity; normal for a longer period in very humid areas.
12
Normal Operating Sounds
iiiiiiiiiiii_iii
You may hear o pinging noisecaused by
water being picked up and thrown against the
condenser on rainy days or when the humidity
ishigh.Thisdesign feature helps remove
moisture and improve efficiency.
You may hear the thermostat click when the
compressor cycles on and off.
iiiiiiiiiiii_iii
iiiiiiiiiiii_iii
Water will collect in the basepan during
high humidity or on rainy days.Thewater
may overflow and drip from the outdoor side
of the unit.
Thefan may run evenwhen the compressor
does not.

Notes.
13

Notes.
14

GEAir Conditioner--One-Vear Limited Warranty. Forcustomers intheU.S.AJ
Staple your receipt here.
Proof of the original purchase date is
needed to make a warranty claim.
We Will Replace:
OneYear I Replacement unit for any product which fails due to a defect in materials or workmanship.
Fromthe dote of the The replacement unit iswarranted for the remainder ofyour product's original one-year
originaipurchase I warranty period.
Properly pack your unit. We recommend usingthe
original carton and packing materials.
Return the product to the retail location where it
was purchased.
Include in the package a copyof the sales receipt or
other evidence of date of original purchase. Also print
your name and address and a description of the defect.
iii
Customer instruction. This owner's manual provides
information regarding operating instructions and
user controls.
Improper installation, delivery or maintenance. If you
have an installation problem, or if the air conditioner is
of improper cooling capacity, contact your dealer or
installer. You are responsible for providing adequate
electrical, plumbing and other connecting facilities.
Failure of the product resulting from modifications to
the product or due to unreasonable use, including failure
to provide reasonable and necessary maintenance.
Replacement of house fuses or resetting of circuit
breakers.
Failure due to corrosionon models not corrosion-
protected.
Damage to the product caused by improper power
supply voltage, accident, fire, floods or acts of God.
Incidental or consequential damage caused by possible
defects with this air conditioner.
Damage caused after delivery.
EXCLUSION OF IMPLIED WARRANTIES--Vour sole and exclusive remedy is product replacement
as provided in this Limited Warranty. Any implied warranties, including the implied warranties of
merchantability or fitness for a particular purpose, are limited to one year or the shortest period
allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know
what your legal rights are, consult your local or state consumer affairs office or your state's Attorney General.
Exclusion of implied warranties: Except where prohibited or restricted by law, there are no warranties,
whether express, oral or statutory which extend beyond the description on the face hereof, including
specifically the implied warranties of merchantability or fitness for a particular purpose.
Warrantor: General Electric Company. Louisville, KY 40225
Z5

ConsumerSupport.
I_l GEAppliances Website IntheU.S.A.:GEAppliances.com
Have a question or need assistancewith your appliance?Try the GEAppliancesWebsite 24 hours a day,
any day of the year! Forgreater convenience and faster service,you can now download Owner's Manuals,
or evenorder parts on-line. InCanada: www.GEAppliances.ca
Real Life Design Studio In theU.S.A.:GEAppliances.com
GEsupports the Universal Designconcept-products, servicesand environments that can be used by
people of all ages,sizesand capabilities. We recognizethe need to designfor a wide range of physical
and mental abilities and impairments. Fordetails of GE'sUniversalDesignapplications, including kitchen design
ideasfor people with disabilities,check out our Website today. Forthe hearing impaired, pleasecall 800.TDD.
GEAC(800.833.4322).
In Canada, contact: Manager, Consumer Relations,MabeCanada Inc.
Suite310, 1 Factory Lane
Moncton, N.B.E1C9M3
Parts and Accessories In the U.S.A.: GEAppliances.com
Individuals qualified to servicetheir own appliances can have parts or accessoriessent directly to their homes
(VISA,MasterCard and Discovercards are accepted).Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal businesshours.
Instructions contained in this manual cover procedures to be performed by any user. GE does not support
any servicing of the air conditioner. We strongly recommend that you do not attempt to service the air
conditioner yourself.
Customers in Canada should consult theyellow pagesfor the nearest Mabe servicecenter,
or call 1.800.561.33/44.
Contact Us In the U.S.A.: GEAppliances.com
If you are not satisfied with the serviceyou receivefrom GE,contact uson our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GEAppliances,Appliance Park
Louisville,K¥/40225
In Canada: www.GEAppliances.ca, or write to: Director, Consumer Relations, Mabe Canada Inc.
Suite 310, 1 Factory Lane
Moncton, N.B. E1C9M3
26

GEAppliances.com
0
Instrucciones de Seguridad... 2,s
Instrucciones de Funcionamiento
Controles ............................. 4
Cuidado y Limpieza
Bobinas Exteriores .................... 5
Filtro de Aire .......................... 5
Instrucciones de Instalaci6n. 6-1o
Consejos para Solucionar
Problemas ......................... 11
Sonidos Normales de
Funcionamiento ..................... 11
Soporte el Cliente
Garantia para Clientes en EE.UU...... 13
Soporte al Cliente .................... 14
AHH08*
AHH:L0*
AHH:L2*
0
Escriba los n_meros de modelo y de serie
aqui:
N°de Modelo
N°de Serie
Estos nOmeros se encuentran en una
etiqueta al costado del acondicionador de
aire
49-7676 12-10 GE

INFORPIACION IMPORTANTE DE SEGURIDAD.LEA TODAS LAS
INSTRUCCIONES ANTES DE USAR.
iADVERTENCIA!
Para su seguridad, siga las instrucciones de este manual a fin de minimizar riesgos de incendio,
descargas el6ctricas o heridas personales.
PRECAUCIONESDESEGURIDAD
Use este electrodom6stico s61opara su
prop6sito original, coma se describe en el
Manual del Propietario.
Este acondicionador de aire se debe instalar
de forma apropiada de acuerdo con las
Instrucciones de Instalaci6n antes de ser
usado.
Nunca desenchufe su acondicionador de aire
empujando el cable de corriente. Siempre tome
su enchufe de manera firme y empuje el mismo
hacia afuera del recept6culo.
Reemplacede inmediatotodos loscablesdel
serviciodeelectricidad peladosocon cualquier
tipo dedaho. Un cable delserviciode corriente
que est6dahado deber6ser reemplazado
por uno nuevoprovisto por el fabricante,y
nodeber6 ser reparado. Nouse un cable con
cortaduras o abrasi6nsobre su extensi6no en
cualquieradesus enchufeso extremos.
Coloquela unidad en OFF(Apagado)y
desenchufe el acondicionador deaire antes de
usar el mismo.
GE no suministra servicio t6cnico para el
acondicionador de aire. Recomendamos
Nunca, bajo ninguna circunstancia, carte o elimine
el tercer cable (tierra) del cable de corriente. Para
su seguridad personal, este electrodom6stico debe
estar adecuadamente conectado a tierra.
enf6ticamente que no intente reparar el
acondicionador de aire usted mismo.
Parasu seguridad..,no acumule ni use
materialescombustibles,gasolina u otros
vapores o liquidos inflamables cerca de6ste u
otto electrodom6stico.
Todos losacondicionadores de aire contienen
refrigerantes,los cuales deacuerdo con la ley
federal se deben quitar antes de deshacerse
del producto.Sise deshar6de un producto
antiguo con refrigerantes,consulte a la
compahia a cargo sobre c6mo deshacersedel
mismo.
Si el recept6culo no coincide con el enchufe, el
cambio del mismo deber6 ser realizado par un
electricista calificado.
Estos sistemas de acondicionadores de
aire R410A requieren que los contratistas y
t6cnicos utilicen herramientas, equipamiento
y est6ndares de seguridad aprobados
para su uso con este refrigerante. NO use
equipamiento certificado s61opara refrigerante
R22.
COMO CONECTARLA ELECTRIClDAD
Contrate a un electricista calificado para que
controle el tomacorriente yel circuito el6ctrico
para asegurar que el enchufe est6 correctamente
conectado a tierra.
2
NO use un enchufe adaptador con este
electrodom6stico.
Elcable de corriente de este electrodom6stico
contiene un enchufe de 3 cables (conexi6n a tierra)
que se conecta a un tomacorriente de pared
est6ndar de 3 cables (conexi6n a tierra) para
minimizar la posibilidad de riesgos de descargas
el6ctricas por parte del mismo.
Elcable de corriente incluye un interruptor de
corriente. Se brinda un bot6n de evaluaci6n y
reinicio en la caja del enchufe. El dispositivo deber6
ser evaluado en forma peri6dica, presionando
primero el bot6n TEST (Evaluar) yluego RESET
(Reinicio) mientras se encuentre enchufado al
tomacorriente. Siel bot6n TEST (Evaluar) no se
activa o el bot6n RESET(Reinicio) no permanece en
su posici6n, deje de usar el acondicionador de aire y
comuniquese con un t6cnico calificado del servicio.
En caso de contar con un tomacorriente de pared
de 2 cables, es su responsabilidad yobligaci6n
reemplazarlo por un tomacorriente de pared de 3
cables correctamente conectado a tierra.
Elacondicionador deaire deberia estar siempre
conectado a unenchufe especificocon un indicede
voltaje equivalente al que figura en su etiqueta de
caracteristicast6cnicas.
Estogarantiza el mejor funcionamiento yadem6s
previenela sobrecarga de loscircuitos del hogar,Io
cual podria ocasionar riesgosde incendio debidoal
recalentamiento decables.
Para conocer los requisitos especfficos de la
conexi6n el6ctrica, consulte las Instrucciones de
Instalaci6n, Requisitos EI6ctricos.

GEAppliances.com
AiADVERTENCIA!
USO DEPROLONGADORES
RIESGO DE INCENDIO. Podda ocasionar
lesiones graves ola muerte.
•NO use un prolongador con este
Acondicionador de Aire de Ventana
• NO use protectores contra picos de corriente ni
adaptadores para mOltiples tomacorrientes con
este Acondicionador de Aire de Ventana
LEAYSIGAESTAINFORMACIONDESEGURIDADCUIDADOSAMENTE.
INSTRUCCIONES

Acerca de los controles enel acondicionador de aire
Los funciones y la apariencia podrdn variar.
Los lucesjunto a los teclas tdctiles del panel de control del acondicionador de aire indican los configuraciones
seleccionadas.
NOTA:La pantalla siempre
muestratatemperatura
del ambiente,exceptoal
ajustarlasfuncionesde
TemperaturaConfigurada
oel Temporizadorde
Retraso.
Tamp /Delay
_od_
e_
z4_Z.)
Tamp /Delay
C'w']
Controles del Acondicionador
de Aire Control Remoto
Controles
4
Tecla de Power (Encendido)
Apaga y prende el acondicionador de aire.
AIencenderse, la pantalla mostrar6 la temperatura
ambiente.
_Pantalla
Huestra la temperatura ambiente o el tiempo
restante en el Sincronizador de retardo. Muestra
la temperatura Definida al configurar la
temperatura en los modos Cool (Frio)o de Energy
Saver (Ahorro de energia). La luz de Ajuste se
encender6 durante la configuraci6n.
Teclas de Tamp Aumento •/Reducci6n •
Usado para ajustar la temperatura cuando
se encuentre en el modo Cool (Frio) oEnergy
Saver (Ahorro de energia). La luz de Ajuste se
encender6 durante la configuraci6n.
Teclade MODO
Usadopara a]ustarel acondicionadordeaire
al modo CoolIFrio),EnergySaver(Ahorrode
energia)oAuto (Autom6tico).
Teclasde Fan Speed(Velocidad del ventilador)
Uselasmismas para configurar la velocidad
del ventilador en Low (Bajo),Mad(Hedio),o High
(Alto)en la unidad.
Tecla de Retraso
Delay ON (RetrasoEncendido)-Cuando el
acondicionador de aire seencuentre apagado,
se podr6 configurar para qua seencienda
autom6ticamente en un periodo de entre 1
y 24 horas en el modo y configuraciones del
ventilador previas.
Delay OFF(Retrasodel Apagado)-Cuando el
acondicionador de aire seencuentre encendido,
se podr6 configurar autom6ticamente para qua
se apague en un per[ado de entre i y 24 horas.
C6mo configurar:
Presionela tecla Delay 1-24hr [Retraso entre
ly24 hrs.) en la unidad o en el control remoto.
Cada vezqua presione lasteclas Increase
(Incrementar) •/Decrease (Reducir)• de la
unidad o lasteclas Increase flncrementar) +
/Decrease (Reducir)- del control remoto se
ajustar6 eltemporizador par intervalosde 1
hora.
Pararevisar el tiempo restante en el
temporizador de Delay 1-24hr (Retrasoentre
ly24 hrs),presione lu teclu Delay l-24hr
(Retraso entre l y 24 hrsJ de lu unidud o
del control remoto. Uselusteclus Increase
(Incrementar) •/ Decrease (Reducir)• de lu
unidod o lusteclus Increase (Incrementar) +/
Decrease (Reducir)- del control remoto puru
configurur un tiempo nuevo siusf Iodeseu.
Para cancelar el temporizador, presione
latecla Delay 1-24hr (Retraso entre l y 24
hrs.) hasta qua la luzde la tecla Delay 1-24hr
(Retraso entre l y 24 hrs.) seapague.