GE 28112EE3 User manual

2. Plug one end of the telephone line cord into the TEL LINE jack on the back of the base
and the other end into a modular jack.
3. Plug the AC power converter into the electrical outlet and the DC connector into the
jack on the back of the base.
4. Place the handset in the base cradle. The charge/in use/VMWI indicator turns on,
verifying the battery is charging.
5. Allow the phone to charge for 16 hours prior to first use. If you don’t properly charge
the phone, battery performance is compromised.
CAUTION: Use only the model 5- 2714 power adaptor that came with
this unit. Using other power adaptors may damage the unit . This power
adaptor is intended to be correctly orientated in a vertical or floor
mount position.
Wall Mounting
1. Turn the base over.
2. Attach the wall mounting pedestal by first inserting the tabs on the open edge of the
pedestal into the slots on the lower portion of the back of the base. Then push down
and snap the pedestal into place.
3. Slip the mounting holes (on the back of the base) over the wall plate posts, and slide
the unit down into place. (Wall plate not included.)
NOTE : If desired, gather the extra telephone line and power adaptor cord
and store inside the wall mounting bracket.
For Model 28112xx2 there will be ONE additional handset, charge cradle, belt
clip, battery pack and cover than shown above.
For Model 28112xx 3 there will be TWO additional handsets, charge cradles,
belt clips, battery packs and covers than shown above.
For Model 28112xx4 there will be THREE additional handsets, charge cradles, belt clips,
battery packs and covers than shown above.
Telephone Jack Requirements
To use this phone, you need an RJ11C type modular telephone
jack, which might look like the one pictured here, installed in
your home. If you don’t have a modular jack, call your local
phone company to find out how to get one installed.
Installation
Digital Security System
Your cordless phone uses a digital security system to protect against false ringing,
unauthorized access, and charges to your phone line.
INSTALLATION NOTE: Some cordless telephones operate at frequencies that
may cause or receive interference with nearby TVs, microwave ovens, and
VCRs. To minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV, microwave ovens,
or VCR. If such interference continues, move the cordless telephone farther
away from these appliances.
Certain other communications devices may also use the 1.9 GHz frequency
for communication, and, if not properly set, these devices may interfere
with each other and/or your new telephone. If you are concerned with
interference, please refer to the owner’s manual for these devices on how to
properly set channels to avoid interference. Typical devices that may use the
1.9 GHz frequency for communication include wireless audio/video senders,
wireless computer networks, multi-handset cordless telephone systems, and
some long-range cordless telephone systems.
Important Installation Guidelines
• Avoid sources of noise and heat, such as motors, fluorescent lighting, microwave
ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the telephone line
has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
Model 28112 Series
DECT 6.0 Cordless
Handset Speakerphone
Answering System
User’s Guide
25840
Important Information
NOTICE: This product meets the applicable Industry Canada technical specifications.
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) This device must accept any interference, including interference
that may cause undesired operation of the device.
The equipment must be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe systems, if present, are
connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the telephone
company.
Base Layout
Modular
telephone
line jack
Wall plate
SEE MARKING ONBOTTOM / BACK OFPRODUCT
RISKOFELECTRICSHOCK
DONOTOPEN
WARNING:TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSETHIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASHAND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE”INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISKOF ELECTRIC SHOCK,DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLEPARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:
Interference Information
This equipment generates and uses radio frequency energy which may interfere
with residential radio and television reception if not properly installed and used in
accordance with instructions contained in this manual. Reasonable protection against
such interference is ensured, although there is no guarantee this will not occur in a
given installation. If interference is suspected and verified by switching this equipment
on and off, the user is encouraged to try to correct the interference by one or more of
the following measures: Reorient the radio/television receiver’s antenna, relocate the
equipment with respect to the receiver, plug the equipment and receiver into separate
circuit outlets. The user may also wish to consult a qualified radio/television technician
for additional suggestions. This equipment has been fully tested and complies with all
limits for Class B computing devices pursuant to part 15 FCC Rules and Regulations.
Telephone Network Information
Should your equipment cause trouble on your line which may harm the telephone
network, the telephone company, where practicable, may notify you that temporary
discontinuance of service may be required. Where prior notice is not practicable and
the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business.
If these changes are expected to affect the use or performance of your telephone
equipment, the telephone company will likely give you adequate notice to allow you to
maintain uninterrupted service.
Notice must be given to the telephone company upon termination of your telephone
from your line.
REN Number
On the bottom of this equipment is a label indicating, among other information, the
Ringer Equivalence Number (REN) for the equipment.
The REN is useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number is
called. In most (but not all) areas, the sum of the RENs of all devices connected to one
line should not exceed 5. To be certain of the number of devices you may connect to
your line as determined by the REN, you should contact your local telephone company.
REN Number is located on the cabinet bottom.
Licensing
Licensed under US Patent 6,427,009.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC/Industry Canada standards for Hearing Aid
Compatibility.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body. This
transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.”
For body worn operation, this phone has been tested and meets the FCC RF exposure
guidelines when used with the belt clip supplied with this product. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines.
Your new GE telephone system is EXPANDABLE
up to a total of 4 handsets (by purchase of optional
Model 28110 handset with charge cradle)
Introduction
CAUTION: When using telephone equipment, there are basic safety
instructions that should always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this product and save them for
future reference.
IMPORTANT: Because cordless phones operate on electricity, you should
have at least one phone in your home that isn’t cordless, in case the power
in your home goes out.
Before You Begin
Parts Checklist (for model 28112xx1)
Make sure your package includes the items shown here.
Handset Layout Installing the Phone
Installing the Handset Battery
NOTE: You must connect the handset battery before use.
CAUTION: To reduce the risk of fire or personal injury, use only the
Thomson Inc. approved model 5-2721 Nickel-metal Hydride battery
(Ni-MH), which is compatible with this unit.
1. Locate battery and battery door which are packaged together inside a plastic bag
and are separate from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment .
NOTE: To ensure proper battery installation, the connector is keyed and can
be inserted only one way.
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.
Base Station
1. Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and place
your cordless telephone on a level surface, such as a desktop or tabletop, or you may
mount it on the wall.
Answering System Setup
This section shows you how to set up your answering system to receive incoming calls.
Before you begin the set up process, you must turn on the answering system.
• Press the ans on/off button to turn the answering system on and off.
The Message Counter indicator lights when the answering system is on. The indicator
blinks when you have new messages.
NOTE: The answering system displays “- -” when it is off.
Setting the Voice Prompt Language
The default voice prompt language is English.
To change the answering system’s voice prompt language,
• Press the language button on front of base to change to the FRENCH voice prompt.
The unit announces “OPTION FRANCAISE “ and Fr shows in the message counter.
• Press the Language button again to change to the SPANISH voice prompt. The unit
announces “SELECCION ESPANOL”and SP shows in the message counter.
NOTE: To change to English, press the Language button again. En shows in
the message counter.
NOTE: In remote access mode, the system follows the selected language. The
voice prompt language cannot be switched remotely.
Voice Time/Day Stamp and Real Time Clock
1. Make sure the answering system is ON.
2. Press and hold the DAY/CHECK button to set the day of the week.
3. Press and hold the HOUR button to set the hour (a.m. or p.m.). Example: 12AM, 1AM, or
12PM, 1PM.
4. Press and release the MIN button to advance the clock in one minute intervals. Press
and hold to increase by 5-minute increments.
5. After the time is set, the real time clock will be displayed on the handset within 1
minute.
NOTE: You must set the day manually. You may choose to setthe time manually
as well, although the time is automatically transmittedby your local phone
company as part ofCaller ID service. If yousubscribe to Caller ID service,the
current time is set automatically whenyou receiveyour first CID record.
Speaker Volume
Use the volume (5 or 6) buttons to adjust speaker volume on the base to a
comfortable level. L1 is the minimum speaker volume and L8 is the maximum.
Voice Instruction
If you need additional assistance, press the review button in standby mode and follow
the voice instructions.
Recording the Outgoing Announcement
For best results when recording, you should be about nine inches from the microphone,
and eliminate as much background noise as possible.
You may record 2 outgoing announcements in the answerer or choose the default for
your current outgoing announcement.
1. Make sure the answering system is ON.
2. Press and hold the announce 1 or announce 2 button until the speaker announces
“RECORD ANNOUNCEMENT AFTER TONE“.
3. Begin speaking after you hear the beep.
4. Release the button when you finish your announcement.
NOTE: If you choose not to record an outgoing announcement, a default
announcement plays instead. To return to the default announcement after
you have recorded your own outgoing announcement, press the announce
button and release it when you hear the beep. Or, press the delete button
while the announcement is reviewing.
Sample Outgoing Announcement
Hi, this is (use your name here), I can’t answer the phone right now, so please leave your
name, number and a brief message after the tone, and I’ll get back to you. Thanks.
NOTE: The maximum recording time for the outgoing announcement is 2
minutes.
Reviewing and Choosing the Announcement
Press and release the announce 1 or announce 2 button to review and select this one as
your outgoing announcement.
NOTE: Press the PLAY/STOP button at any time to stop playing announcement.
USER NAME
HANDSET X
Programming the Telephone
Standby Screen
The handset displays the handset number and user name.
Programming Functions
The system uses a menu structure to give you access to all of the built-in features. You
may program the following items in main menu: Room Monitor and Handset Setup.
Room Monitor (applicable only with additional handsets)
1. Make sure your phone is OFF (not in talk mode).
2. Press the mute/program button to go to the main menu.
3. Press caller ID-volume ( 6or 5) button to scroll to ROOM MONITOR.
4. Press mute/program button to enter ROOM MONITOR menu, ROOM MONITOR
EXTENSION? shows in the display.
5. Use the touch tone pad to enter the handset name/number to be monitored.
NOTE: When this phone system is expanded (up to 4 handsets by purchase
of optional Model 28110 handset with recharge cradle), handsets are named
HANDSET 1, HANDSET 2, HANDSET 3 and HANDSET 4 respectively.
6. The receiving handset will turn on the microphone and the originating handset will
turn on the speakerphone to monitor sound from the receiving handset.
NOTE: For room monitoring mode to work, the originating handset must NOT
be on the cradle.
NOTE: While in room monitoring mode, the handsets will emit an alert tone
approximately every 5 seconds if there is an incoming call. You may press
the SPEAKER button to quit room monitor and answer the call.
NOTE: While in room monitoring mode, the originating handset can be
switched to monitor by handset earpiece by pressing the TALK/CALL BACK
button once. Switch back to speakerphone by pressing the SPEAKER
button once.
NOTE: Press the *TONE/exit button on the handset to exit room
monitor mode.
Handset Setup
1. Make sure your phone is OFF (not in talk mode).
2. Press the mute/program button to go to the main menu.
3. Press caller ID-volume ( 6or 5) button to scroll to HANDSET SETUP.
4. Press mute/program button to confirm and you may program the following items:
Language, Handset Name, Ringer Tone, Ringer Volume, VIP Melody, Key Tone,
Message Alert, Rings to Answer, Security Code, Area Code, Tone/Pulse, Registration,
Deregistration and Default Setting.
NOTE: During programming, you may press the *TONE/exit button at any
time to exit the sub-menu and return to the menu.
Language
From the Handset Setup Menu:
1. Pressthe caller ID-volume ( 6or 5) button toscroll to the SETLANGUAGE sub-menu.
2. Press mute/program button to enter the menu. SET LANGUAGE 1ENG 2FRA 3ESP
shows in the display.
3. Use the touch tone pad on the handset to select 1ENG, 2FRA, 3ESP, or use the
caller ID-volume ( 6or 5) button to scroll to the desired language. English is the
default setting.
4. Press the mute/program button to save your selection. You will hear a confirmation
tone and the selected language shows in the display.
Model 28112
00015927 (Rev. 2 CAN E)
06-46
Printed in China
Thomson Digital Technologies Ltd.
© 2006 Thomson Digital Technologies Ltd.
Trademark(s) ® Registered
Marque(s) déposée(s)
Base
Handset
Belt clip
Telephone
line cord
AC power
adaptor
Handset
battery pack
Battery
compartment cover
Wall mount
bracket
PLAY
STOP
13
REVIEW SKIP
1
2
MEMO
VOLUME
DELETE
ANNOUNCE
ANSON/OFF LANGUAGE
HANDSETPAGE DONOTDISTURB
CHARGE/INUSE
DECT
TM
INTERFERENCEFREE
COMMUNICATION
r
e
v
p
l
a
y
s
t
o
p
s
k
i
p
e
r
a
s
e
TALK
CALL
BACK
DECT
format
conf
redial SPEAKER program
delete
int mute
ABC
DEC
GHI
JKL
MNO
PO
RS TUV
WX
YZ
OP
ER
memory flash
0
#
123
456
789
c
a
l
l
e
r
I
D
-
v
o
l
u
m
e
exit
a
n
s
w
e
r
e
r
r
e
v
p
l
a
y
s
t
o
p
s
k
i
p
e
r
a
s
e
TALK
CALL
BACK
DECT
format
conf
redial SPEAKER program
delete
int mute
ABC
DEC
GHI
JKL
MNO
PO
RS TUV
WX
YZ
OP
ER
memory flash
0
#
123
456
789
c
a
l
l
e
r
I
D
-
v
o
l
u
m
e
exit
a
n
s
w
e
r
e
r
format/conf
(format/conference
button)
display
SPEAKER
(button)
skip (button)
#pause/ringer
(button)
memory (button)
erase
(button)
flash/answerer
(button)
mute/program
(button)
int (button)
redial
(button)
* TONE/exit
(button) play/stop
(button)
rev (review
button)
TALK/CALL BACK
(button)
caller ID-volume
(button)
delete
(button)
SPEAKER
caller ID-volume
(button)
13
1
2
memo
volume
delete
announce
anson/off language
page donot disturb
charge/inuse
charge/in use/VMWI
(indicator) ans on/off
(answerer button)
announce1
(button)
announce2
(button)
delete
(button)
review
(button)
PLAY/STOP
(button)
skip
(button)
do not disturb
(button/indicator)
memo
(button)
volume
(buttons)
language
(button)
SPEAKER
Message Counter
(indicator)
page
(button)
DAY/CHECK
(button)
HOUR
(button) MIN
(minute button)
black wire
red wire
battery
pack
PRESS DOWN
FIRMLY
> ROOM MONITOR
EXTENSION?
VMWI Indicator

- Press the caller ID-volume ( 5) to review the oldest call and scroll toward the most
recent calls (higher numbers).
- Press the caller ID-volume ( 6) to review the newest call and scroll to older calls
(lower numbers).
NOTE: You may choose from three last dialed numbers.
4. Press the TALK/CALL BACK button. The number dials automatically.
If you get a busy signal and want to keep dialing the number, press the redial button to
quickly redial the number.
Exit
Press the *TONE/exit button to exit a menu function and return to the standby screen.
Page
The page feature helps you locate a misplaced handset. To send and receive pages, all
handsets must be registered. If your handset is not registered, follow the instructions in
the Registration section of this manual.
Handset to Handset Paging (applicable only with additional handsets)
1. Make sure the phone is OFF (not in talk mode).
2. Press and release the int button on a handset. PAGING EXTENSION? shows in
the display.
3. Use the touch-tone pad to enter the handset number you want to page.
4. To cancel the page, press the *TONE/exit, int, or TALK/CALL BACK button on the
originating handset, or press the *TONE/exit button on the receiving handset.
Paging All Handsets from a Handset (applicable only with additional hand-
sets)
1. Make sure the originating phone is OFF (not in talk mode).
2. Press and release the int button on a handset. PAGING EXTENSION? shows in
the display.
3. Use the touch-tone pad to enter the handset number you want to page. (1= to page
Handset 1, 2=to page handset 2, etc., and 5=to page all handsets)
4. To cancel the page, press the *TONE/exit, int, or TALK/CALL BACK button on the
originating handset, or press the *TONE/exit button on the receiving handset.
Paging from the Base/Group Page
Use the base-only to page all registered handsets at the same time.
1. Press the page button on the base. All handsets beep for two minutes, and PAGING
FROM BASE shows on each handset’s display.
2. To cancel the page, press the page button on the base, or press the TALK/CALL BACK
button or the *TONE/exit button on each handset.
Mute
To have a private, off-line conversation, use the MUTE feature. The party on the
telephone line cannot hear you, but you can hear them.
1. Press the mute/program button. The handset display shows MUTE ON.
2. Press the mute/program button to cancel and return to your phone conversation.
Receiver Volume Control
When the handset is ON (in talk mode) you may adjust the receiver volume by pressing
the caller ID-volume ( 6or 5) button. There are four volume levels to choose from.
When the maximum or minimum volume level is reached, the phone beeps twice. VOL
1 is minimum and VOL 4 is maximum.
Do Not Disturb (DND)
DND allows you to mute the ringer on all handsets.
In the standby mode, press the do not disturb button on the base. The DND indicator
will light and DO NOT DISTURB shows in handset display. To cancel, press the do not
disturb button again.
Intercom Operation (applicable only with additional handsets)
The intercom feature allows you to have a conversation with another registered
handset without tying up the telephone line, allowing you to still receive incoming calls.
Making an Intercom Call
1. Make sure the handset is OFF (not in talk mode).
2. Press the int button on the handset.
3. Use the touch-tone pad to select the handset you want to page.
NOTE: To cancel page, press the int button again or the *TONE/exit button
on the sending handset.
Handset Name
From the Handset Setup Menu:
1. Pressthecaller ID-volume ( 6or 5) button to scroll to the HANDSET NAME sub-
menu.
2. Press mute/program button to enter the menu. HANDSET NAME shows in the
display.
3. Usethetouch-tonepad toentera name(up to15 characters).More thanone letteris stored
ineachof thenumberkeys.For example,to enterBillSmith,pressthe 2 keytwicefor the letter
B.Press the 4 key3 timesfor the letterI. Pressthe 5 key 3 timesfortheletterL. Pressthe 5 key
3 timesforthe secondletterL, andpressthe 1 key toinserta space betweenthefirstandlast
name.Pressthe 7 key 4 timesfortheletterS; pressthe 6 key oncefor the letterM; pressthe 4
key3 timesfor the letterI; pressthe 8 key for theletter T;press the 4 keytwicefor the letterH.
NOTE: If you make a mistake, use the delete button to backspace and delete
one character at a time.
4. Press the mute/program button to save your name. You will hear a confirmation tone
and the handset name shows in the display.
Ringer Tone
You may choose from ten different ringer tones and ten different melodies.
From the Handset Setup Menu:
1. Press thecaller ID-volume ( 6or 5) buttonto scrollto the RINGER TONE sub-menu.
2. Press mute/program button to enter the menu. SET RINGER TONE 01 shows in the
display. 01 is default setting.
3. Use the caller ID-volume ( 6or 5) button to scroll to the desired setting (1 through
20). You will hear a sample of the ringer tone/melody you select.
4. Press the mute/program button to save your selection. You will hear a confirmation
tone and the selected ringer tone shows in the display.
NOTE: You must have the Ringer Volume set to ON for ring tone to signal an
incoming call.
Ringer Volume
From the Handset Setup Menu:
1. Pressthe caller ID-volume ( 6or 5) buttonto scrollto the RINGER VOLUME sub-menu.
2. Press mute/program button to enter the menu. SET RINGER 1HI 2LO 3OFF shows in
the display.
3. Use the touch tone pad on thehandset to select 1, 2 or 3,or use the caller ID-volume
( 6or 5) button toscroll to your selection. HI is the default setting.
4. Press the mute/program button to save your selection. You will hear a confirmation
tone and the new volume setting shows in the display.
NOTE: If you turn the ringer OFF, the ringer off icon shows in the display.
VIP Melody
This features allows you to assign a specific melody to someone you want to get your
attention when the person calls. When a VIP melody is assigned and that person calls,
the unit rings the normal ring for the first ring and then follows with VIP melody ring.
You may choose from ten different polyphonic melodies and may store up to 10 VIP
records.
NOTE: This feature ONLY works when the following conditions are met.
1. You have subscribed to Caller ID.
2. You have your Caller ID record previously transferred to the memory.
(Refer to Storing CID Records in Internal Memory). NO USER MEMORY will
show in the display to remind the user to do CID record transfer first.
Storing VIP Melody
From the Handset Setup Menu:
1. Press the caller ID-volume ( 6or 5) button to scroll to VIP MELODY sub-menu.
2. Press mute/program button to select VIP melody feature and then display VIP 1
record.
-If VIP1 does NOT contain any specific number/records, it will display EMPTY.
3. Press caller ID-volume ( 6or 5) button to select the specific VIP melody memory
location (10 VIP locations) that does not contain any record.
4. Press mute/program button to display SELECT MEMORY.
NOTE: If the memory location does not contain any CID memory records and you
are trying to mark a specific record as VIP MELODY, then SELECT MEMORY will not
be displayed. Instead, NO USER MEMORY will display in prompt to alert the user.
5. Press caller ID-volume ( 6or 5) button to view the records from memory to be selected
as VIP .
6. Press mute/program button to confirm and then display VIP MELODY 01 to wait for
the melody tone selection.
7. Press caller ID-volume ( 6or 5) button to select from melody 01 to melody 10
(a testing tone is generated while making melody selection)
8. Press mute/program button to confirm.
NOTE: If the desired number/record was previously stored in any one of the
ten VIP melody records, DUPLICATE NUMBER shows in the display.
Changing a Stored VIP Melody Record
Use the Storing VIP Melody procedure to change the number of a selected record and
replace the old phone number with new phone number.
When REPLACE VIP# ? shows in the display, you must press mute/program button on
the handset to confirm replacement.
Reviewing And Deleting Stored VIP Melody Record
From the Handset Setup Menu:
1. Press the mute/program button to enter to VIP MELODY menu.
2. Use the caller ID-volume ( 6or 5) button to scroll to the desired VIP Melody Record.
3. If you want to delete the information, press the delete button on the handset while
the entry displays. The display show DELETE VIP# ?.
4. Press delete again to confirm. You will hear a confirmation tone and VIP# DELETED
shows in the display.
Key Tone
From the Handset Setup Menu:
1. Press the caller ID-volume ( 6or 5) button to scroll to the KEY TONE sub-menu.
2. Press mute/program button to enter the menu. SET KEY TONE 1ON 2 OFF shows in
the display.
3. Use the touch tone pad on the handset to select 1 or 2, or use the caller ID-volume (
6or 5) button to scroll to your selection. 1ON is the default setting.
4. Press the mute/program button to confirm and the key tone setting sh ows in
the display.
Message Alert (for answering system)
This feature sets your answering system to give an alert tone every 10 seconds when
there are new messages.
From the Handset Setup Menu:
1. Press the caller ID-volume ( 6or 5) button to scroll to the MESSAGE ALERT sub-
menu.
2. Press mute/program button to enter the menu. NEW MSG ALERT 1ON 2OFF shows in
the display.
3. Use the touch-tone pad to enter the selection, or use the CALLER ID-VOL (6or 5)
button to scroll to the 1ON or 2OFF. The default setting is 2OFF.
4. Press the mute/program button to confirm. You will hear a confirmation tone and
the new setting shows in the display.
Rings to Answer (for answering system)
This feature lets you select the number of times you want the phone to ring before the
answering system answers a call.
From the Handset Setup Menu:
1. Pressthecaller ID-volume ( 6or 5) buttonto scrollto theRING TO ANSWERsub-menu.
2. Press mute/program button to enter the menu. RING TOANSWER3 4 5 6 TS shows in
the display.
3. Use the caller ID-volume ( 6or 5) button to scroll to the your selection. The default
setting is 5.
4. Press the mute/program button to confirm. You will hear a confirmation tone and
the new setting shows in the display.
NOTE: If you select Toll Saver (TS) the unit answers after the 3rd ring if there
are NEW messages, OR the unit answers after the 5th ring if there are NO
new messages. This allows user to access their answerer from another
location and then hang up after 4 rings to save long distance charges.
3. Use the touch-tone pad to select 1for YES or 2for NO. Or use the caller ID-volume
( 6or 5) button to scroll to 1YES or 2NO.
WARNING: It is not recommended that a handset be de-registered
unless absolutely necessary because once a handset is de-registered,
that handset’s telephone features cannot be used until the handset is
re-registered.
4. Select NO, if you do not want to de-register.
5. If you select YES, press the mute/program button and MOVE NEAR TO BASE displays
for 2 seconds, then CONFIRM? 1YES 2NO appears in the display.
6. Press the touch-tone pad to select 1YES or 2NO, or use the caller ID-volume ( 6or
5) button to scroll to 1YES or 2NO.
7. If you select YES, press the mute/program button to confirm. DE-REGISTER... shows
in the display. You will hear a confirmation tone. Then HANDSET X DEREGISTERED
shows in the display to confirm the handset is deregistered.
NOTE: When you complete the de-registration process, HANDSET
NEEDS REGISTRATION shows in the display. To use the handset,
you MUST re-register the handset using the Registration process.
Global De-registration
If one or more handsets becomes lost, you should de-register all handsets to ensure
proper system operation. Follow the steps below to de-register all handsets at the
same time.
WARNING: It is not recommended that a handset be de-registered unless
absolutely necessary because once a handset is de-registered, that
handset’s telephone features cannot be used until the handset is re-
registered.
1. Disconnect power from the base by pulling the plug out of the back of the unit.
2. Press and hold the Page button and while holding the Page button reconnect the
power.
3. Continue to hold the Page button until the charge/in use light flashes rapidly.
4. Release the Page button
5. Press and release the page button on the base once. All handsets are de-registered
and HANDSET NEEDS REGISTRATION shows in the display.
Default Setting
As you become familiar with this system, you may prefer to use the system’s original
settings. Follow the steps below to return to the factory default settings.
From the Handset Setup Menu:
1. Press the caller ID-volume ( 6or 5) button toscroll to the DEFAULT SETTING sub-
menu.
2. Press the mute/program button to enter the menu. DEFAULT SETTING 1YES 2NO
shows in the display.
3. Use the touch-tone pad to select 1YES or 2NO, or use the caller ID-volume ( 6or 5)
button to move the cursor to 1YES or 2NO. 2NO is default setting.
NOTE: If you choose YES all the settings in the programmable menu are
returned to factory default setting.
4. Press the mute/program button to save your selection. You will hear a
confirmation tone.
Telephone Operation
Visual Indicators
charge/in use/VMWI Indicator on Base
The charge/in use/VMWI indicator on the base will flash to alert you to an incoming
call, during paging, or if you have a message waiting from your service provider. The
indicator will remain lit when a handset is in the base charging or when the line is
in use.
TALK/CALL BACK Indicator on Handset
The TALK/CALL BACK and SPEAKER indicator buttons flash when you receive a call and
remain lit during a call.
VMWI Indicator on Handset
IMPORTANT: In order to use this unit’s Visual Message Waiting
Indicator (VMWI) feature, you must subscribe to this service from your
phone company.
The VMWI indicator on the top of the handset flashes when you receive a new message
from your service provider.
Speakerphone Operation .
NOTE: If you are using the speakerphone, remain close to handset so the
party you are speaking to can hear you.
If you are using the handset and want to switch to the speakerphone, press the
SPEAKER button, press SPEAKER again to end conversation.
If you are using the speakerphone and want to switch to the handset, press the TALK/
CALL BACK button, press TALK/CALL BACK again to end conversation.
Making a Call
1. Press the TALK/CALL BACK or SPEAKER button. Dial the desired number.
- OR -
Dial the number first, then press the TALK/CALL BACK or SPEAKER button.
- OR -
Press the caller ID-volume ( 6or 5) button to select the desired record, then press
the TALK/CALL BACK or SPEAKER button.
2. When finished, press the TALK/CALL BACK or SPEAKER button to hang up.
NOTE: You may enter up to 32 pre-dial digits.
NOTE: If you want to delete the pre-dial number you entered, press the
delete button until all of the digits are erased.
Answering Calls
1. When the phone rings, press the SPEAKER button on the handset.
- OR -
Pick up the handset and press the TALK/CALL BACK button.
2. When finished, press SPEAKER or TALK/CALL BACK to hang up.
NOTE: Adjust the handset volume by pressing the caller ID-volume
( 6or 5) button during a call.
Call Timer
After youpress theTALK/CALL BACK button on thehandset, thebuilt-in calltimer shows on
the display andcounts the length of time ofthe call in minutes and seconds.
Auto Standby
If you place the handset in the cradle while the handset is off the hook (during a call),
the call is automatically disconnected.
Ringer HI/LO/OFF (Shortcut)
There are two ways to set the ringer to HI/LO/OFF. One is the traditional way as
described in the Programming Functions; Handset Setup; Ringer Volume menus. The
other one is this short cut to ringer menu.
1. Make sure the phone is OFF (not in talk mode).
2. Press the #pause/ringer button to display SET RINGER 1HI 2LO 3OFF.
3. Use the touch tone pad onthe handset toselect 1,2 or 3, or use the caller ID-volume
( 6or 5) buttonto scrollto your selection.HI is the default setting.
4. Press #pause/ringer button again to save and display the new selection for a
few seconds.
Flash/Call Waiting
If you subscribe to the combined Call Waiting Caller ID service from your local telephone
company, you will receive Caller ID information (if available) on Call Waiting calls. During a
phone call, you will hear a beep to indicate another call is waiting on the line and Caller ID
information for the waiting call shows on the handset display.
• To connect to the waiting call, press the flash/answerer button on the handset, and
your original call is put on hold.
• To switch between the two calls, press the flash/answerer button.
TIP: Do not press the TALK/CALL BACK button on the handset to activate a
custom calling service, such as call waiting, or call will disconnect.
Last Number Redial
You may redial a number up to 32 digits long. To quickly redial the last number
you dialed:
1. Press the TALK/CALL BACK button.
2. Press the redial button.
-OR-
3. Press the redial button first, then use the caller ID-volume ( 6or 5) button to select
the desired redial number.
4. Wait for the person at the receiving handset to press the int button.
NOTE: If the receiving handset does not answer within two minutes, the
intercom call is automatically canceled. The originating handset displays
NO ANSWER.
5. When finished, press the *TONE/exit button or int button on either handset to
deactivate the intercom.
NOTE:The system is expandable up to 4 handsets (by purchase of optional
Model 28110 handset with recharge cradle). When 4 handsets are
registered, the system can handle 2 separate intercom operations at once,
for example, 1st handset intercoms with 2nd handset while 3rd handset
intercoms with 4th handset.
Receiving an Intercom Call
When you receive an intercom call, your handset beeps. To answer the call press the int
button or TALK/CALL BACK button.
Advanced Intercom Features
Receiving an Incoming Call During an Intercom Call
If you receive a telephone call during an intercom call, the intercom call is immediately
terminated and both handsets ring. Either handset user may press the TALK/CALL BACK
button to answer the call.
Using Intercom with External Telephone Calls
During a telephone call, you may use the intercom/paging function to page another
handset and have an off line, private (two-way) intercom conversation. You may also
have a three-way conversation between the external caller and the handsets, or you
may transfer the external telephone call to another handset.
NOTE: Before you intercom/page another handset, you must decide
whether you want to create a two-way or a three-way conversation.
Two-Way Calling
1. During an external call, press the int button, and use the touch-tone pad to enter the
handset number you want to call.
NOTE: The receiving handset presses the int button to answer the intercom
call. Both intercom users may speak privately. The external caller will not
hear the intercom conversation.
2. When finished, press the *TONE/exit button or int button to end the intercom call,
return to the talk mode, and resume your original telephone conversation.
Three-Way Calling
1. During an external call, press the int button. LINE ON HOLD EXTENSION? shows in
the display.
2. Use the touch-tone pad to select Handset #. You will hear a paging tone and
PAGING shows in the originating handset’s display.
NOTE: PAGING FROM... shows in the display on the receiving handset, and
the receiving handset presses the int or TALK/CALL BACK button to answer
the intercom.
3. When the receiving handset connects, press the format/conf button on the
originating handset to conference with the receiving handset and the external
caller. CONFERENCE shows in the display on the originating and receiving handsets.
NOTE: A handset can enter conference mode directly by pressing TALK/
CALL BACK on the second handset during a call.
Transferring External Calls to Other Handsets
During an external call, you may transfer the external call to another handset.
1. Press the int button on the originating handset to put an external call on hold, and
then page the receiving handset.
2. Use the touch-tone pad on the handset to select Handset #. You will hear a paging
tone. PAGING shows on the originating handset’s display, and PAGING FROM...
shows on the receiving handset’s display.
3. When the receiving handset connects, press the TALK/CALL BACK button on the
originating handset to transfer the call.
-OR-
4. Press the TALK/CALL BACK button on the originating handset to transfer the call. If
the receiving handset does not answer within 30 seconds, the originating handset
rings back and displays CALLBACK. If the originating handset does not answer
within 20 seconds, the call is automatically dropped.
Security Code (for answering system)
You can access the answering system from a tone dialing telephone in another
(remote) location. The security code is required for remote access, and it prevents
unauthorized access to your answering system.
From the Handset Setup Menu:
1. Press the caller ID-volume ( 6or 5) button to scroll to the SECURITY CODE sub-
menu.
2. Press mute/program button to enter the menu. SECURITY CODE 1 2 3 shows in
the display.
3. Use the touch-tone pad to enter your new 3-digit security code. The default setting is
123.
4. Press the mute/program button to confirm. You will hear a confirmation tone and
the new security code shows in the display.
NOTE: If you make a mistake, use the delete button to delete the security
code and begin again.
Area Code
From the Handset Setup Menu:
1. Press the caller ID-volume ( 6or 5) button to scroll to the AREA CODE sub-menu.
2. Press mute/program button to enter the menu. SET AREA CODE - - - shows in
the display.
3. Use the touch-tone pad to enter your 3-digit area code.
4. Press the mute/program button to confirm. You will hear a confirmation tone and
the new area code shows in the display.
NOTE: To restore the default setting to - - -, press and release delete when
SET AREA CODE shows in the display.
Tone/Pulse
From the Handset Setup Menu:
1. Press the caller ID-volume ( 5or 6) button to scroll to the TONE PULSE sub-menu.
2. Press mute/program button to enter the menu. TONE/PULSE 41TONE 2PULSE
shows in the display. The default setting is “1 TONE”.
3. Use the touch-tone pad or caller ID-volume ( 5or 6) to enter 1 TONE or 2 PULSE.
4. Press the mute/program button to confirm. You will hear a confirmation tone and
your selection shows in the display.
Registration
Your packaged handset(s) are pre-registered and ready to use. It is not
recommended that a handset be registered again unless absolutely necessary.
From the Handset Setup Menu:
1. Press the caller ID-volume ( 6or 5) button to scroll to the REGISTRATION sub-menu.
2. Press the mute/program button to enter the menu. REGISTRATION 1YES 42NO - - -
shows in the display The default setting is "2NO".
3. Use the touch-tone pad to select 1for YES or 2for NO. Or use the caller ID-volume (
6or 5) button to scroll to 1YES or 2NO.
4. If you select YES, press the mute/program button. HOLD BASE PAGE FOR 5
SECONDS, THEN PRESS HANDSET PROGRAM shows in the display. (Your handset
should be held near the base during registration process.)
5. Press and hold the page button on the base unit until the CHARGE /IN USE indicator
flashes. Press the handset mute/program button. REGISTERING shows in the display.
HANDSET X REGISTERED shows in the handset display, where X is the handset
number. You may now rename your handset. (Refer to Step 3 & 4 of Handset
Name Section)
NOTE: IF you are re-registering the handset through the handset menu; to
rename your handset you must go to the Handset Name Section and start
from the beginning step.
De-Registration
De-registration cancels registration. During the de-registration process, keep the
handset near the base.
From the Handset Setup Menu:
1. Press the caller ID-volume ( 6or 5) button to scroll to the DEREGISTRATION sub-
menu.
2. Press the mute/program button to enter the menu. DEREGISTRATION 1YES 42NO
- - - shows in the display The default setting is "2NO".

Call Waiting Caller ID
Provided you subscribe to Call Waiting Caller ID service from your phone company;
if you receive an incoming call and you are using the GE multi handset system, a beep
indicates the presence of a Call Waiting call on the line. The Call Waiting Caller ID
information will be displayed and stored in the history of all handsets in the system.
• When you hear the call waiting beep in the handset receiver, press the flash/
answerer button to put the current call on hold and answer the incoming call.
Press FLASH/ answerer again to return to the original call.
Receiving CID Records
When you receive a call, the Caller ID information is transmitted between the first and
second ring. The Caller ID information appears on the display while the phone rings,
giving you a chance to monitor the information and decide whether or not to answer
the call.
Storing CID Records (In CID Memory)
If you are not at home or cannot answer, your telephone’s Caller ID memory stores the
data for the 40 most recent calls you received so you can see who called while you
were unavailable. When the 41st call is received, the oldest Caller ID record (1st call) is
automatically deleted.
You may review the stored information at any time. Calls received since your last
review show as NEW in the display. Calls that have not been previously reviewed but
were received from the same number more than once show as REPT in the display.
Reviewing CID Records
As calls are received and stored, the display is updated to let you know how many calls
have been received. To scroll CID records:
1. Make sure the phone is OFF (not in talk mode).
2. Press the caller ID-volume ( 6) button to review the newest CID record.
3. Press the caller ID-volume ( 5) button to review the oldest CID record first.
Dialing a CID Number
1. Make sure the phone is OFF (not in TALK mode).
2. Use the caller ID-volume ( 6or 5) button to display the desired record.
3. Press the TALK/CALL BACK or SPEAKER button. The number dials automatically.
NOTE: Depending on (a) how the incoming caller’s phone number is
formatted when it is received, and (b) whether or not you previously pre-
programmed your local area code into the set up menu, you may need to
adjust the format of the incoming caller’s stored phone number before
making the call, press the format/conf button to adjust the number, and try
again.
Available formats include:
Number of digits Explanation Example
Eleven digits long distance code “1 ” 1-317-888-8888
+3-digit area code
+7-digit telephone number.
Ten digits 3-digit area code + 317-888-8888
7-digit telephone number.
Seven digits 7-digit telephone number. 888-8888
Storing CID Records in Internal Memory
You may also store CID information in the phone’s internal memory.
NOTE: It is important that you format CID records correctly BEFORE
storing in internal memory as you cannot reformat CID records
stored in memory.
1. Make sure the phone is OFF (not in talk mode).
2. Use the caller ID-volume ( 6or 5) button to scroll to the desired CID record.
3. Press the Memory button to display SELECT MEMORY 01-50.
4. Use the touch-tone pad to enter a memory location to store the number in that
memory location. You will hear a confirmation tone.
NOTE: If the memory location is occupied, REPLACE MEMO? is displayed, and
you must confirm replacement by pressing the memory button.
NOTE: Press the *TONE/exit button once to keep the previous setting
(making no changes) and return to the menu.
NOTE: If the selected CID record contains any information that is non-
numeric, the unit will not allow this record to transfer to the internal user
memory. The handset will display UNABLE TO STORE.
To Replace a Stored CID Record
1. Repeat steps 1 through 3 in Storing CID Records in Internal Memory. After you enter
the memory location, REPLACE MEMO? shows in the display.
2. Press the Memory button again, and the new CID record replaces the old memory in
that location. You will hear a confirmation tone.
Deleting a CID Record
1. Make sure the phone is OFF (not in TALK mode).
2. Use the caller ID-volume ( 6or 5) button to display the CID record you want to
delete.
3. Press the delete button. The display shows DELETE CALL ID?
4. Press the delete button to erase the record showing in the display. The display shows
DELETED.
NOTE: Press the *TONE/exit button to return to the standby mode without
deleting any CID records.
Deleting All CID Records
1. Make sure the phone is OFF (not in TALK mode).
2. Use the caller ID-volume ( 6or 5) button to display any Caller ID record.
3. Press and hold the delete button until DELETE ALL? shows in the display.
4. Press delete button to erase all of the current CID records. The display shows
DELETED followed by NO CALLS.
NOTE: Press the *TONE/exit button to return to the standby mode without
deleting any CID records.
Memory
Each handset can store up to fifty 20-digit numbers with up to 15-character names in
memory for quick dialing. This memory feature is in addition to the CID memory log,
which stores up to 40 CID records in each handset.
Storing a Name and Number in Memory
1. Make sure the phone is OFF (not in talk mode).
2. Press the memory button to display SELECT MEMORY 01-50.
3. Press the desired memory location button (01 through 50) or use the caller ID-
volume ( 6or 5) button to scroll to desired the memory location.
NOTE: If the memory location is occupied, the memory location number and
stored name and telephone number shows in the display. If the memory
location is empty, EMPTY shows in the display.
4. Press the memory button. The display shows ENTER NAME.
5. Use the touch-tone pad to enter a name (up to 15 characters). More than one letter
is stored in each of the number keys. For example, to enter Bill Smith, press the 2 key
twice for the letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times
for the letter L. Press the 5 key 3 times for the second letter L, and press the 1 key to
insert a space between the first and last name. Press the 7 key 4 times for the letter
S; press the 6 key once for the letter M; press the 4 key 3 times for the letter I; press
the 8 key for the letter T; press the 4 key twice for the letter H.
NOTE: If you make a mistake press the delete button to backspace and
erase the wrong character(s) or number(s).
6. Press the memory button to confirm and save the record. The display shows ENTER
TEL NUMBR.
7. Use the touch-tone pad to enter the telephone number (up to 20 digits, including
pauses (press #PAUSE button), and press the memory button again to save the
record. The unit beeps to confirm.
NOTE: The system treats PAUSES as delays or spaces in the dialing
sequence.
8. To enter another name and number in a different memory location, return to step 2
and repeat the process.
Storing the Last Number Dialed
You may transfer all three redial numbers into internal user memory.
1. Make sure the phone in OFF (not in TALK mode).
2. Press redial button to display the most recent redial number.
3. Use the caller ID-volume ( 6or 5) button to scroll to desired redial number.
4. Press memory button to display SELECT MEMORY 01 - 50.
5. Use touch-tone pad to enter two digit desired memory location (01 through 50).
Display will show ENTER NAME.
6. Follow step 5 in the “Storing a Name and Number in Memory” section to
enter name.
NOTE: If the memory location is occupied, REPLACE MEMO? is displayed,
and you must confirm replacement by pressing the memory button.
7. Press memory button to save.
8. To enter another name and number in a different memory location, return to step 2
and repeat the process.
NOTE: If the redial number has more than 20 digits, it cannot be stored
in memory.
Inserting a Pause in the Dialing Sequence (of a Stored
Number)
Press the #pause/ringer button on the handset’s touch-tone pad to insert a delay in
dialing sequence when a pause is needed to wait for a dial tone (for example, after you
dial 9 for an outside line, or to wait for a computer access tone.) Each pause counts as
one digit in the dialing sequence.
Reviewing Records Stored in Memory
1. Make sure the phone is OFF (not in talk mode).
2. Press the memory button to display SELECT MEMORY 01-50.
3. Press the caller ID-volume ( 6or 5) buttons to scroll the records, or use the
handset’s touch-tone pad to enter the memory location number.
Changing Records Stored in Memory
Follow the procedure for Storing Names and Numbers in Memory, except replace a
stored telephone number with a new one.
Deleting Records Stored in Memory
1. Make sure the phone is OFF (not in talk mode).
2. Press the memory button to display SELECT MEMORY 01-50.
3. Press the caller ID-volume ( 6or 5) button to scroll to the record you want to delete
or use the touch-tone pad to enter the desired memory location.
4. Press the delete button to mark the record for deletion. The display shows DELETE?
5. Press the delete button to delete the record. DELETED shows in the display.
NOTE: If you don’t want to change or delete a record, simply press
the *TONE/exit button, or wait for one minute to exit the review mode
automatically.
Dialing a Number from Memory
1. Make sure the phone is ON (in talk mode) by pressing the TALK/CALL BACK or
SPEAKER button.
2. Press the memory button to display MEMO # - -.
3. Use the touch tone pad to enter the memory location number. The number dials
automatically.
-OR-
1. Make sure the phone is OFF (not in talk mode).
2. Press the memory button to display SELECT MEMORY 01-50.
3. Press the memory location for the phone number you want to dial, or use the caller
ID-volume ( 6or 5) button to scroll to the number you want to dial.
4. Press the TALK/CALL BACK or SPEAKER button. The number dials automatically.
Chain Dialing from Memory
Use this feature to make calls from records stored in memory which require a sequence
of numbers, such as a calling card number used for a frequently called long distance
number. The following example shows how you can store each part of the dialing
sequence and use chain dialing to make a call through a long distance service:
The Number For Memory Location
Long Distance Access Number 7
Authorization Code 8
Frequently called long distance number 9
1. Make sure the phone is ON (in talk mode) by pressing the TALK/CALL BACK or
SPEAKER button.
2. Press the memory button, and then press 07.
3. When you hear the access tone, press the memory button, and then press 08.
4. At the next access tone, press the memory button and then 09.
Answering System Operation
This section discusses the buttons and features on the answering system.
Message Counter Indicator
The message counter gives you a numeric display of how many messages you have.
The new message indicator flashes to indicate you have new messages. See below for
the details.
a) Message counter has a number displayed without flashing - No new messages.
Shows total number of old messages.
b) Message counter has a flashing number displayed - There are new messages.
Shows total number of old and new messages.
c) Message counter has bars ( - - ) - Answerer is off.
d) Message counter has an “F“ flashing on the display - Memory is full.
e) Message counter has a “CL” flashing on the display - Clock is not set since power up
or after power failure.
f) Message counter has six horizontal bars flashing on the display - MEMO recording.
g) Message counter has a “An“ flashing on the display - Answering incoming calls and
recording an incoming call.
h) Message counter has “LA” - The answering system is being accessed remotely.
i) Message counter has a “A1“ or “A2“ on the display - Announcement 1 or
Announcement 2 is selected as an current outgoing announcement during
Announcement selection and announcement recording/playing.
j) Message counter has “En“ on the display - English is selected as the current voice
prompt during language selection.
k) Message counter has “Fr“ on the display - French is selected as the current voice
prompt during language selection.
l) Message counter has “SP“ on the display - Spanish is selected as the current voice
prompt during language selection.
NOTE: While the messages are playing, the message counter will display
the messages in the order they were received.
NOTE: The maximum recording time for each message is 3 minutes and the
total recording time of this unit is 12 minutes.
Leaving a Message/Memo
Use the memo feature to leave a message.
1. Press and hold the memo button.
2. Begin speaking after you hear “RECORD MESSAGE” and start tone.
3. Release the memo button when you are finished recording the memo.
NOTE: Maximum recording time for memo is 3 minutes.
Screening Calls from the Base
1. When the answering system answers the call, listen while the caller leaves a
message (to determine who is calling).
2. To speak to the caller, pick up the handset, and press the TALK/CALL BACK or
SPEAKER button.
The answering system automatically stops recording when you activate the handset or
pick up an extension phone.
TIP: Make sure the volume on the base is set loud enough to hear your
incoming calls.
Messages Playback
The message counter let you know when you have message(s) or new message(s). To
play the messages, press the PLAY/STOP button.
While a message is playing, you may do the following:
• Press the corresponding PLAY/STOP to stop the message playback.
• Press and release the review button to restart the current message.
• Press and release the review button twice to go to the previous message.
• Press and release the skip button to go to the next message.
• Press the delete button to erase the current message.
Memory Full
When the answering system memory is full, the system answers after 10 rings. You
should erase some messages so the answering system may record new messages.
Erasing Messages
You may erase messages in the following three ways:
To erase a message while it is playing
1. Press and release PLAY/STOP button.
2. Pressthe reviewand skip buttons toselect andplaythe message youwantto erase.
3. Press the delete button, the current message is erased, and the next message plays.
To erase all previously played Messages in a mailbox
1. Make sure the phone is OFF (not in talk mode)
2. Press and hold the delete button until “ALL OLD MESSAGES ERASED” is announced.
To erase a message from the handset :
1. Press the flash/answerer button on the handset
2. Pressthe play/stop(key 2) on the handset.
3. Pressthe erase (key 0) on the handset to erase a message during playback.
NOTE: Erased messages cannot be restored.
Remote Access
You may access the answering system with the cordless handset or from any tone-dial
compatible telephone.
Cordless Handset
Use the corresponding handset keys just like you would use the base buttons (see
“Answering System Setup”). The button functions are located on the handset above
each number key. For example, to play messages:
• Press the flash/answerer button. The display shows ANSWERER REMOTE ACCESS.
• Press 2 ( play/stop ) to play the message.
• When you are finished listening to your messages, press the flash/answerer button
again.
Screening Calls from the Handset
Use the handset to screen calls even when you can’t hear the answering system.
When the answering system picks up:
1. Press the flash/answerer button to access the answering system. CALL SCREENING
shows on the display.
2. Listen as the caller leaves a message.
3. Press the TALK/CALL BACK or SPEAKER buttons to speak to the person or press the
flash/answerer button to stop screening the call.
Accessing the Answering System from Another Location
You can access your answering system from any touch-tone phone by entering your
3-digit security code during the playing of outgoing announcement or after you hear
the outgoing announcement.
1. Dial the telephone number to which the answering system is connected.
2. Enter the security code during the outgoing announcement or after you hear the tone.
Note: The default security code is 123
3. Follow the voice menu to use the answering system’s remote functions.
The remote feature lets you perform the following functions:
To Press this button
Review message 1
Play back messages 2
Stop message playback 2
Erase message 0 (during message playback)
Skip message 3
Turn off/on answerer 4
Review voice menu options 7
Memory Full
When answering system memory is full, the system answers after 10 rings, beeps and
waits for you to enter the 3-digit security code. If you don’t enter the security code
within 8 seconds, the phone hangs up.
You should erase some messages so the answering system can record new messages.
NOTE: The unit also answers after the 10th ring if it is turned off. To access
the answering system, enter your 3-digit security code.
Belt clip and Optional Headset
Connecting the Belt Clip
1. To attach the belt clip, insert the sides of the belt clip into the slots on each side of
the handset.
2. Snap the ends of the belt clip into place.
Connecting an Optional Headset to the Handset
Each handset can be used with an optional headset hands free operation.
1. Connect the headset to the headset jack on the side of the handset. The handset
receiver and microphone are disabled when the headset is connected.
2. Adjust the headset to rest comfortably on top of your head and over your ear. Move
the microphone to approximately two to three inches from your mouth.
3. Press the TALK/CALL BACKbutton to answer a call ormake calls using the headset.
4. To return to normal operation, unplug the headset from the jack.
Changing the Battery
CAUTION: To reduce the risk of fire or personal injury, use only the
Thomson Inc. approved model 5-2721 Nickel-metal Hydride battery
(Ni-MH), which is compatible with this unit.
1. Make sure the telephone is OFF (not in TALK mode) before you replace the battery.
2. Remove the battery compartment door.
3. Disconnect the battery plug from the jack inside the battery compartment and
remove the battery pack from the handset.
4. Insert the new battery pack and connect the cord to the jack inside the battery
compartment.
5. Put the battery compartment door back on.
6. Place handset in the base or handset charge cradle to charge. Allow the handset
battery to properly charge (for 16 hours) prior to first use or when you install a
new battery pack. If you do not properly charge the phone, battery performance
will be compromised.
Battery Safety Precautions
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type,
toxic materials could be released which can cause injury.
• To reduce the risk of fire or personal injury, use only the Nickel-metal Hydride
battery listed in the User’s Guide.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 days.
Display Messages
The following messages shows the status of the phone, provides Caller ID information,
or helps you set up and use your phone.
BLOCKED NUMBER Indicates the person is calling from a number which is blocked
from transmission.
CHARGING... Indicates the handset needs to charge for a period of time
before it can resume normal function.
DELETE ALL? Prompt asking if you want to erase all CID records.
DELETE CALL ID? Prompt asking if you want to erase the CID record showing on
the display.
DELETE? Prompt asking if you want to erase one of the 50 records
stored in the phone’s memory.
DUPLICATE NUMBER Under VIP melody feature, if the desired number/record was
selected in any one of TEN VIP melody records before,
DUPLICATE NUMBER shows in the display.
END OF LIST Indicates that there is no additional information in CID memory.
ENTER NAME Prompt telling you to enter a name in one of the 50
memory locations.
ENTER TEL NUMBR Prompt telling you to enter a telephone number in one of the
50 memory locations.
NEW Indicates call or calls which have not been reviewed.
HANDSET NAME Prompt telling you to enter the user name for the
registered handset.
HANDSET NEEDS Indicates you must register a non-registered handset prior
REGISTRATION to use.
INCOMPLETE DATA Caller information is interrupted during transmission or the
phone line is excessively noisy. Indicates no CID information
was received, you are not subscribed to CID service, or CID
service is not working.
LINE IN USE Displays on handset while the line is in use.
LONG DISTANCE Indicates CID record is from a long distance call.
LOW BATTERY Indicates the battery needs to be charged.
NEW VOICE MAIL Indicates voice mail has not been retrieve from service provider.
CALL SCREENING Indicates you may use the handset to screen calls before
answering the call
NEW CALL XX XX represents the number of new CID records not reviewed.
NO CALLS Indicates there are no CID records in memory.
NO USER MEMORY Indicates the memory location contains no user memories and
the user is trying to mark a specific user record for VIP MELODY.
OUT OF RANGE May indicate handset is too far away from the base or that
the power has been interrupted. Move closer and
check connections.
PAGING or Someone pressed the page button on the base or
PAGING FROM int button on the handset
REPT Indicates a repeat call message. Indicates a new call from the
same number was received more than once.
SEARCHING Indicates handset is searching for the base.
SPKR Indicates the handset is in speakerphone mode.
UNKNOWN CALLER/ Indicates incoming call is from an area not serviced by CID or
NAME/NUMBER the CID information was not sent.
Time call received Date call received Number of calls
Caller’s nameCaller’s phone number
Caller ID (CID)
IMPORTANT: In order to use this unit’s Caller ID features, you must
subscribe to either the standard Name/Number Caller ID Service or Call
Waiting Caller ID Service. To know who is calling while you are on the
phone, you must subscribe to Call Waiting Caller ID Service.
This unit receives and displays information transmitted by your local phone company.
This information can include the phone number, date, and time; or the name, phone
number, date, and time.
NOTE: The RBRC seal on the battery used in your Thomson Inc. product
indicates that we are participating in a program to collect and recycle the
rechargeable battery (or batteries).
For more information go to the RBRC web site at www.rbrc.org
or call 1-800-8-BATTERY or contact a local recycling center.

Answering System Display Messages
The following messages show the status of the answering system or help you set up
and use the system.
0-59 Indicates the total number of messages.
CL (blinking) The voice time/day stamp needs to be set.
- - Answering system is turned off.
An (blinking) The system is answering a call.
F (blinking) Answering system memory is full.
Six bars (blinking) The system is recording a memo or an announcement.
LA (Line Access) External line remote answering system.
Handset Sound Signals
Signal Meaning
A long warbling tone (with ringer on) Signals an incoming call
Three short beeps (several times) Page signal
One beep every 7 seconds Low battery warning
Troubleshooting Guide
Telephone Solutions
No dial tone
• Check or repeat installation steps:
Make sure the base power cord is connected to a working electrical outlet.
Make sure the telephone line cord is connected to the base and the wall jack.
• Connect another phone to the same jack. If it doesn’t work, the problem might be
your wiring or local service.
• The handset may be out of range of the base. Move closer to the base.
• Make sure the battery is properly charged (for 16 hours).
• Make sure the battery pack (in the handset) is properly installed.
• The handset should beep when you press the TALK/CALL BACK button, and the
charge indicator on the base should be lit when the handset rests in the cradle. If
not, the battery may need to be charged.
• Place handset in charge cradle for at least 20 seconds to reset the unit.
Handset does not ring
• Make sure the handset ringer software switch is set to on.
• The handset may be out of range of the base. Move closer to the base.
• You may have too many extension phones on your line. Try unplugging some
extensions.
• Check for a dial tone.
You experience static, noise, or fading in and out
• The handset may be out of range of the base. Move closer to base.
• Make sure base is not plugged into an electrical outlet with another household
appliance. If necessary, relocate the base.
• Charge the battery (for 16 hours).
Unit beeps
• Clean the charging contacts on the cordless handset and base charge cradle with a
soft cloth or an eraser.
• See solutions for “No dial tone ” on previous page.
• Replace the battery.
Memory dialing doesn’t work
• Did you program the memory location keys correctly?
• Did you follow proper dialing sequence?
Unit locks up and no communication between the base and cordless handset
• Unplug the power adaptor from the electrical outlet and the back of the base.
Remove the handset battery. Wait for 30 seconds and plug the power adaptor back
into the base and electrical outlet. Reconnect the battery and charge for 16 hours.
Caller ID Solutions
No Display
• Charge the battery (for 16 hours). Or replace the battery.
• Make sure the unit is connected to a non-switched electrical outlet. Disconnect the
power adaptor from the base and reconnect it.
Caller ID Error Message
• The unit displays this message if it detects anything other than valid Caller ID
information during the silent period after the first ring. This message indicates the
presence of noise on the line.
No Caller ID
• You must be subscribed to the standard Name/Number Caller ID service from your
local telephone company to receive CID information.
Battery
If you experience any of the following problems, even after recharging the battery, you
may need to replace the battery pack:
• Short talk time
• Poor sound quality
• Limited range
• Charge indicator fails to turn on
Answering System Solutions
Can’t hear messages, beep, etc.
• Adjust speaker volume.
Time/Day setting stuck at 12 a.m Mon.
• Set the time clock.
Answers on 10th ring
• Make sure answering system is turned on.
• Answering system memory may be full. Erase some messages.
Incoming messages are incomplete
• An extension phone may have been lifted as a message is received.
• Answering system memory is full. Erase some messages.
• You may have accidently pressed the play/stop button during playback and stopped
the message.
Won’t respond to remote commands
• You must use a tone-dial phone. This phone does not support pulse (rotary) dialing.
• Make sure to enter the correct security code.
• Did unit hang up? If you take no action for a period of time,
it automatically hangs up.
Accessory Information
DESCRIPTION MODEL NO.
Handset Replacement Battery 5-2721
AC Power converter 5-2714
Belt Clip 5-2717
Headset 5-2425
Handset charge cradle 5-2716
To order, call the nearest distributor for your area;
Ontario: [phone] Manitoba: [phone]
British Columbia: [phone] Quebec: [phone]
A shipping and handling fee will be charged upon ordering.
It is required by law to collect appropriate sales tax for each individual state,
country, and locality to which the merchandise is being sent. Items are subject to
availability.
Causes of Poor Reception
• Aluminum siding.
• Foil backing on insulation.
• Heating ducts and other metal construction that can shield radio signals.
• You ’re too close to appliances such as microwaves, stoves, computers, etc.
• Atmospheric conditions, such as strong storms.
• Base is installed in the basement or lower floor of the house.
• Base is plugged into AC outlet with other electronic devices.
• Baby monitor is using the same frequency.
• Handset battery is low.
• You’re out of range of the base.
General Product Care
To keep your unit working and looking good, follow these guidelines:
• Avoid dropping the handset, aswell as other rough treatmentto the phone.
• Clean the phone with a soft cloth.
• Never use strong cleaning agents, paint thinner, abrasive powder, alcohol, or other
chemical products to clean the unit. Doing so will damage the finish.
• Retain the original packaging in case you need to ship the phone at a later date.
• Periodically clean the charge contacts on the handset and base with a clean pencil
eraser.
Service
Thomson Digital Technologies Ltd., warrants to the purchaser or gift recipient that
if any manufacturing defect becomes apparent in this product within 1 year from
the original date of purchase, it will be replaced free of charge, including return
transportation.
This warranty does not include damage to the product resulting from accidents, misuse
or leaking batteries.
Should your product not perform properly during the warranty period, either:
1. Return it to the selling dealer with proof of purchase for replacement,
OR
2. Remove the batteries (where applicable), and pack product complete with
accessories in the original carton (or equivalent).
— Mail prepaid (with proof of purchase) and insured to:
Thomson Digital Technologies Ltd.
6200 Edwards Boulevard
Mississauga, Ontario
Canada L5T 2V7
The provisions of this written warranty are in addition to and not a modification of or
subtraction from the statutory warranties and other rights and remedies contained
in any applicable legislation, and to the extent that any such provisions purport to
disclaim, exclude or limit any such statutory warranties and other rights and remedies,
such provisions shall be deemed to be amended to the extent necessary to comply
therewith.
If you are unable to find a qualified servicer for out of warranty service, you may
write to:
Thomson Digital Technologies Ltd.
c/o Thomson Inc.
P.O. Box 0944
Indianapolis, Indiana, U.S.A., 46206-0944
Attach your sales receipt to this booklet for future reference. This information is
required if service is needed during the warranty period.
PURCHASE DATE ___________________________________________
NAME OF STORE ______________________________________________