GE Monogram ZBD4700XWW User instructions

Revised 7/97
Monogram.
™
UL
R
Listed by
Underwriters
Laboratories
For answers to your GE Monogram,™GE Profile,™
GE, Hotpoint and RCA appliance questions, call
GE Answer Center®service, 800.626.2000.
ZBD4700XWW—Dishwasher with stainless steel interior
Dimensions and Specifications (in inches)
Design Information: This dishwasher is supplied as
a white model.
This dishwashers has a finished door and access
panel. The door and access panel trim will accept
custom panels up to 1/4" thick.
A toekick is supplied and may be covered with a
custom toekick to match kitchen decor.
Side trim is not required. Side filler strips are supplied
to fill a 24" wide opening.
Additional Specifications: A 120 Volt, 60 Hz power
supply is required. An individual properly grounded
branch circuit protected by a 15 or 20 amp circuit
breaker or time delay fuse is recommended. Install a
3-prong electrical receptacle at least 6" above the
floor and within 18" of the right or left adjacent
cabinet wall. Wiring must enter the cutout in shaded
area shown. A double, side-by-side installation
requires two separate circuits.
The hot water line must enter the cutout in the shaded
area from the right, left, rear or through the floor. The
water line should be 3/8" O.D. copper or 1/2" O.D.
plastic. Installation of an easily accessible hand
shut-off valve is strongly recommended.
The dishwasher should be placed no more than 10
feet from the sink for proper drainage.
If the dishwasher is to be located in or near a corner
of base cabinets, allow 2" min. clearance from the
corner to prevent interference with adjacent door
handles.
23 3/8"
4"
5 1/2"
34" Min.
35" Max.
Toekick
25 1/4"
From Inside
Front Frame 22 5/8"
3 3/16"
24"
1-3/4" Min.
6"
PlumbingandElectricService
MustEnterInsideThisArea
34" Min.
35" Max.
Underside of
Countertop
to Floor
23-5/8" Min.
24" Max.
This Wall Area
Must be Free of
Pipes or Wires

Revised 7/97
Monogram.
™
UL
R
Listed by
Underwriters
Laboratories
For answers to your GE Monogram,™GE Profile,™
GE, Hotpoint and RCA appliance questions, call
GE Answer Center®service, 800.626.2000.
ZBD4700XWW—Dishwasher with stainless steel interior
Dimensions and Specifications (in inches)
Cut 1/4" thick door panel: 23-1/4" wide, 22-11/16" high.
Cut 1/4" thick access panel: 23-1/4" wide 1-1/2" high.
Cut edges of the panels will be concealed by the trim.
Cut a notch in the top corners of the door panel. 1/8"
wide and 3/16" deep. This will allow the panel to slide
under the escutcheon. The bottom corners of the door
panel trim and all 4 corners of the access panel trim
are rounded. Therefore, for a good fit, a 5/16" radius
cut is required.
1/4" Thick
Door Panel 22 11/16"
1 1/2"
23 1/4"
1/4" Thick Access Panel
5/16"
Radius
Cut
Notch 1/8"
3/16"
1/4" Custom Door and Access Panel Dimensions

Revised 7/97
Monogram.
™
ZBD4700XWW—Dishwasher with stainless steel interior
Monogram
PREWASH
DELAY
START
POTS
& PANS HI
TEMP ON
OFF FILL
RINSE RINSE & HOLD
CHINA & CRYSTAL RINSE & DRY
NORMAL WASH
POTS & PANS
AID
WASH RINSE DRY
Features and Benefits
• White on white Model
• Triple Sound Insulation Package
• Stainless Steel Interior
• Cycle Selections: Pots & Pans, Normal Wash,
China/Crystal, Rinse & Hold, Rinse & Dry
• 4 Wash Levels
• Stainless Steel Multi-Axis Lower Wash Arm
• Triple Filter System
• Adjustable Nylon Upper Rack
• Nylon Lower Rack with Removable Tine Inserts
• Deluxe Silverware Basket
• 2 Utility Shelves
• 9-Hour Delay Start Option
• Water Heat On/Off
• Convection Drying
• Model ZBD4700XWW—White on white
• Model ZBD4700XBB—Black on black