GE Profile DPXH46GACC/WW User instructions

DPXH46GACC/WW—GE Profile™Extra-Large 5.7 Cu. Ft. Capacity Front-Load Dryer
Specification Revised 2/02
TM
Dryer Dimensions (in inches)
Exhaust Options:
When viewed from the front of the unit, exhaust 3-way via rear, right and bottom. Dryer is
shipped exhausted to the rear. Alternate exhausting knockouts are supplied.
Gas Dryer Electric Rating: 120V, 60Hz, 6A
An individual properly-grounded branch circuit, with a three-prong grounding-type receptacle,
protected by a 15 or 20 amp circuit breaker or a time-delay fuse is required.
Gas (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP gas. LP gas supply
requires a conversion kit. Check installation instructions for correct kit and have a qualified
gas technician install a conversion kit. See dryer ducting information for proper installation.
Note: Dryer wall outlet must be located within 36" of service cord entry and accessible
when dryer is mounted in position.
Installation Information: For complete information, see installation instructions packed
with your dryer.
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,
® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
REAR VIEW
26-7/8
3-3/4
1
36
Under
Counter
34-5/8"
3/16"
Gas Pipe Connection
Electric
Connection
2-9/16
13-9/16
SIDE VIEW
25-3/4
47-1/2
4-3/4
Optional
Vent Knockout
Door Open
90°4-3/8
3/4

TM
Specification Revised 2/02
DPXH46GACC/WW—GE Profile™Extra-Large 5.7 Cu. Ft. Capacity Front-Load Dryer
Undercounter Installation
• Accessory mounting kits are required for
undercounter installation. To order,
call 1-800-848-7722.
Washer—Order Pub. No. 14-A037
Dryer—Order Pub. No. 14-A008
Stacked Installation
•Brackets for stacking dryer over washer
are included with the dryer.
Alcove or Closet Installation
•If your dryer is approved for installation
in an alcove or closet, it will be stated
on a label on the dryer back.
•The dryer MUST be exhausted to the
outdoors.
•Minimum clearances between dryer
cabinet and adjacent walls or other
surfaces are:
0" either side
3" front and rear
•Minimum vertical space from floor to
overhead cabinets, ceilings, etc. is 52".
•Closet doors must be louvered or
otherwise ventilated and must contain
a minimum of 60 sq. in. of open area
equally distributed. If this closet contains
both a washer and a dryer, doors must
contain a minimum of 120 sq. in. of
open area equally distributed.
•The closet should be vented to the
outdoors to prevent gas pocketing in
case of a gas leak in the supply line.
•No other fuel-burning appliance shall be
installed in the same closet with the dryer.
Bathroom or Bedroom Installation
•The dryer MUST be exhausted to the
outdoors.
•The installation must conform with the
local codes, or in the absence of local
codes, with the National Fuel Gas Code,
ANSI Z223.
Minimum Clearances other than Alcove
or Closet Installations
•Minimum clearances to combustible
surfaces:
0" both sides
3" rear
36"
25-3/4" 53-1/2"
Washer
Top Sheet Dryer
Top Sheet
Countertop
14''
29'' 56''-60''
Lip on All Sides
3/4" High x 3/4" Wide
Max.
70-5/8"
25-3/4"
26-3/4"
Free-Standing Installation
Undercounter Installation
Raised/Built-In Installation
Stacked Installation
For more information on venting kits and
accessories, please call 1-800-GE-CARES.
Special Installation Requirements
For answers to your Monogram,
®GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
R
Listed by
Underwriters
Laboratories

DPXH46GACC/WW—GE Profile™Extra-Large 5.7 Cu. Ft. Capacity Front-Load Dryer
Specification Revised 2/02
TM
Dryer Exhausting Information—Use Metal Duct Only
For answers to your Monogram,
®GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
0 60 ft. 48 ft. 30 ft. 18 ft.
1 52 ft. 40 ft. 22 ft. 14 ft.
2 44 ft. 32 ft. 14 ft. 10 ft.
Front Loading 3 32 ft. 24 ft.
Dryers 4 28 ft. 16 ft.
Number
of
90°
Turns
Maximum Length of 4"
Dia. Rigid Metal Duct
Maximum Length of 4"
Dia. Flexible Metal Duct
Exhaust Hood Type Exhaust Hood Type
A
4" Opening
B
2-1/2"
Opening
A
4" Opening
B
2-1/2"
Opening
A
4
Best Performance
B
2-1/2
For complete information, see installation instructions packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4”diameter all rigid metal exhaust duct. If “all rigid metal”
duct cannot be used, then “flexible all metal”venting can be used, but it will reduce the maximum recommended
duct length.
Exhaust Length Calculation:
1. Determine the number of 90°turns needed for your installation. If you exhaust to the side or bottom of dryer, add
one turn.
2. The maximum length of 4’rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. The
maximum length for flexible ducts are less than for rigid duct.
A turn of 45°or less may be ignored. Two 45°turns within the duct length should be treated as a 90°elbow. A turn
over 45°should be treated as a 90°elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large amounts of moisture and lint
from being blown into the room. Gas dryers or any dryer located in a closet must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space),
or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never termi
nate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease
could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap
must also be located at least 12”above the ground or any other obstruction with the opening pointed down. Other
terminations, such as louvered wall boxes, are acceptable provided they are equivalent to a 4”opening dampered
wall cap.

TM
Specification Revised 2/02
DPXH46GACC/WW—GE Profile™Extra-Large 5.7 Cu. Ft. Capacity Front-Load Dryer
6Cycle / 4 Fabric CareSettings/ DeluxeQuiet Plus
FABRICCAREWRINKLECARE
EXTENDEDCOOLAIRTUMBLE
START
COTTONS
REG.HEAT
AIRFLUFF
NOHEAT
PERMPRESS
MED.HEAT
KNITS/DELICATES
LOWHEAT
EASY CARE
OPTIMUMDRY
WRINKLE
CARE
TIMEDDRY
OPTIMUMDRY
MOREDRY
LESSDRY
ONOFFON
20
30
40
5060
10
COOL
DOWN
MOREDRY
COOL
DOWN
WRINKLECARE
LESSDRY
MORE
DRY
OPTIMUM
DRY
LESSDRY
DELICATES
COTTONS
Features and Benefits
•Extra-Large (5.7 cu. ft.) Capacity
•Sensor Dry
•ColorLogic™2000
•Tumble Drying
•4 Temperature Options: Regular/Cottons, Medium/Permanent Press, Low/Delicates and
Air Fluff/No Heat (Cool Down)
•1 Time Dry Cycle
•3 Auto Dry Cycles: Cottons, Easy Care and Knits/Delicates
•2 Wrinkle Care Cycles
•Moisture Sensor
•Fixed End-of-Cycle Signal
•Quick Clean Lint Screen
•Drying Rack
•Spill-Saver Top
•Interior Dryer Light
•Dura Finish Top and Drum
•Leveling Legs
•Heavy Duty Suspension System
•4 Exhaust Option
•Reverse-A-Door
•100% Front Serviceable
•Model DPXH46EAWW - White on white (Electric)
•Model DPXH46EACC - Bisque on bisque (Electric)
•Model DPXH46GAWW - White on white (Gas)
•Model DPXH46GACC - Bisque on bisque (Gas)